• Applied Science and Convergence Technology
• /
• 제26권4호
• /
• pp.79-85
• /
• 2017

The crack-free AlGaN template has been successfully grown by using selective area growth with triangular GaN facet. The triangular GaN stripe structure was obtained by vertical growth rate enhanced mode with low growth temperature of $950^{\circ}C$ and high growth pressure of 500 torr. The lateral growth rate enhanced mode of AlGaN for crack-free and flat surface was also investigated. Low pressure of 30 torr and high V/III ratio of 4400 were favorable for lateral growth of AlGaN. It was confirmed that the $4{\mu}m$ -thick $Al_{0.2}Ga_{0.8}N$ was crack-free over entire 2-inch wafer. The dislocation density of $Al_{0.2}Ga_{0.8}N$ was as low as ${\sim}7.6{\times}10^8/cm^2$ measured by cathodoluminescence. Based on the high quality AlGaN with low dislocation density, the ultraviolet laser diode epitaxy with cladding, waveguide and GaN/AlGaN multiple quantum well (MQW) was grown by metalorganic chemical vapor deposition. The stimulated emission at 349 nm with full width at half maximum of 1.8 nm from the MQW was observed through optical pumping experiment with 193 nm KrF laser. We also have fabricated the deep ridge type ultraviolet laser diode (UV-LD) with $5{\mu}m-wide$ and $700{\mu}m-long$ cavity for electrical properties. The turn on voltage was below 5 V and the resistance was ${\sim}55{\Omega}$ at applied voltage of 10 V. The amplified spontaneous emission spectrum of UV-LD was also observed from pulsed current injection.

• 융합신호처리학회논문지
• /
• 제22권3호
• /
• pp.104-109
• /
• 2021

본 논문에서는 self-seeding FP-LD (Fabry Perot Laser Diode)를 이용하여 WDM-PON (Wavelength Division Multiplexing - Passive Optical Network)에서 사용될 수 있는 새로운 파장 가변 광원의 가능성을 검증한다. 파장 가변 광원을 이용한 WDM-PON의 기존 구현은 AWG (Arrayed Waveguide Grating) 소자의 중심 파장과 광원의 중심 파장을 세밀히 정렬해 주어야 하는 단점이 발생한다. 그러나, 본 논문에서 제안하는 파장 가변 광원은 매우 간단한 구조로 구성되며, 가변 파장이 AWG의 중심 파장에 자동 정렬되는 장점을 갖는다. 구현된 파장 가변 광원은 약 14 nm 정도 이상의 파장 가변 대역을 보였고, 상대적 세기 잡음, RIN (Relative Intensity Noise)은 최대 약 -124dB/Hz로 나타났으며, 외부 변조기를 통해 변조한 결과 10Gb/s 신호에 대한 변조 가능성을 확인 할 수 있었다.

• 한국레이저가공학회지
• /
• 제2권1호
• /
• pp.30-37
• /
• 1999

Laser-welded Tailored Blank is the hottest thing in many automobile companies. But they demand on weld quality, reproducibility, and formability. So it is the great problem of automation of laser welding process. Therefore, it is requested to construct on-line process monitoring system on high accuracy. The light which is emitted from plasma and spatter in laser welding was detected by photo-diodes. It was found that the light intensity depends on welding speed. laser power, and flow rate of assist gas. The relationship between the plasma and spatter and the weld quality can be used for on-line laser weld monitoring systems.

• 조명전기설비학회논문지
• /
• 제29권12호
• /
• pp.28-32
• /
• 2015

In this work, we reported fabrication of sealing the glass substrate using laser treatment at low temperature for electrochemical luminescence (ECL) cell. The laser treatment at temperature is using laser diode. The glass substrate sealing by laser treatment tested at 3-10W, 2-5 mm/s for build and tested. The sealing laser treatment method will allow associate coordination between the two glass substrate was enclosed. The effect of laser treatment to sealing the glass substrate was found to have cracks and air gap at best thickness of about 550-600 im for condition 3 W, 3 mm/s. The surface of sealing was roughness which was not influent to electrodes It can reduce the cracks, crevices and air gaps as well, improves the performance viscosity in butter bus bar electrodes. Therefore, it is more effective viscosity between two FTO glasses substrate.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.434-439
• /
• 1993

Described is a stabilizing circuit of the Doppler beat signal obtained by the coherence-dependent fiber-optic laser Doppler velocimeter (LDV), which employs both a self-mixing laser diode (SM-LD) and a 10m-100m long optical fiber. The stabilizing circuit maintains the SM-LD drive current at an optimum value, which gives a maximum Doppler signal during long hours.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.275-276
• /
• 2011

We have investigated the holographic grating formation on Ag-doped amorphous chalcogenide As2Se3 thin films with Ag layer. The basic optical parameter which is a refractive index and extinction coefficent was taken by n&k analyzer. The source of laser was selected based on these parameter. Holographic gratings have been formed using He-Ne laser (wavelength: 632.8 nm) Diode Pumped Solid State laser (DPSS, wavelength: 532.0 nm) under [P:P] polarized the intensity polarization holography. The diffraction efficiency was obtained by +1st order intensity.

• 대한두경부종양학회:학술대회논문집
• /
• 대한두경부종양학회 2003년도 제20차 학술대회
• /
• pp.221-221
• /
• 2003

• 전자공학회논문지A
• /
• 제31A권6호
• /
• pp.134-142
• /
• 1994

A kink due to the lasing of the first transverse mode in laser diodes is investigated using rate equations based on the spatial hole burning model. An analytic expression for the kink power is derived and the result agrees well with experimental results. It is also shown that the position of a kink can be identified in the electrical derivative characteristics as well as in light output vs, current characteristics.

• Journal of the Optical Society of Korea
• /
• 제11권2호
• /
• pp.63-66
• /
• 2007

A 9.6 dB gain is observed at 1310 nm in a 5.0 cm bismuth-doped silica fiber. A launched pump power of 100 mW was obtained using an 810-nm laser diode. We demonstrated the simultaneous optical amplification at two wavelengths near second telecommunication windows, which is the range of zero-dispersion for silica fibers.

• 소성∙가공
• /
• 제24권4호
• /
• pp.272-279
• /
• 2015

The characteristics of the laser metal deposition parameters were studied to enhance the deposition efficiency using a diode pumped disk laser. STD61 hot tool steel plate and Fe based AISI M2 alloy were used as a substrate and powder for the laser metal deposition, respectively. Among the laser metal deposition parameters the laser power, track pitch and powder feed rate were used to estimate the deposition efficiency. From the experimental results, the deposition efficiency was shown to be excellent when 1.8kW laser power 500um track pitch and 10g/min of the powder feed rate were used. For this optimal condition the average hardness of the deposition track was approximately 830HV, and this value is 30~50% better than the hardness of the commercially produced tool steel after heat treatment.