• Journal of Mechanical Science and Technology
• /
• v.14 no.2
• /
• pp.177-187
• /
• 2000

Dilution is an important factor which influences the properties of clad layer. In this paper the change of dilution during laser cladding and the control of dilution are simulated by a finite element method. The adaptive mesh method is adopted for the time-dependent finite element method computation so that the shape of melt pool can be well represented. The situation of the width control of melt pool is also simulated, which indicates that the dilution can be controlled if the width of melt pool is controlled. Computational results indicate that if a line energy (input energy per unit distance) remains constant the dilution will increase with time, especially at the beginning. Simulation results show that it is possible to control dilution in a certain range if the line energy decreases with time. Experiment of Nd: YAG laser cladding with wire feeding is performed. Experiment results coincide well with the FEM results.

• Korean Journal of Clinical Pharmacy
• /
• v.7 no.2
• /
• pp.86-90
• /
• 1997

This study was to find a more accurate method fur measuring small vancomycin dosages which are commonly used in neonates by comparing single and double dilution method. For single dilution method, 500 mg of vancomycin powder was accurately measured and reconstituted with 5 ml of distilled water to make a concentration of 100 mg/ml. Volumes of 0.05, 0.1, 0.15, 0.2, 0.3, 0.4, and 0.5 ml, which equal the target dosages of 5, 10, 15, 20, 30, 40, and 50 mg, were measured using syringes made by Shina and each sample was further diluted with 2 ml of $5\%$ dextrose. The solution of 100 mg/ml concentration was further diluted with $5\%$ dextrose to make a concentration of 20 mg/ml. Volumes of 0.25, 0.5, 0.75, 1.0, 1.5, 2.0, and 2.5 ml, which correspond to 5, 10, 15, 20, 30, 40, and 50 mg, were sampled by the same Shina's syringe as in single dilution method and then each sample was further diluted to make a total volume of 10 ml. Each sample was analyzed by HPLC. The measured dosages of each sample in both single and double dilution methods were lower than the target dosages; however, e values in double dilution method were higher than those in single dilution method for seven target dosages. Percent target dosages in single dilution method were 65 to $90\%$, while in double dilution method 91 to $94\%$. Statistically significant difference between two groups was shown in 5, 10, 15, 20, and 40 mg dosages (p<0.05). In conclusion, when preparing small vancomycin dosages lower an 20 mg $(volume{\leq}0.2\;ml)$, using Shina's syringes, the double dilution method has a closer value to the target dosage than single dilution method.

• Asian-Australasian Journal of Animal Sciences
• /
• v.3 no.2
• /
• pp.143-148
• /
• 1990

An experiment was conducted to compare the traditional weigh-suckle-weigh method and the $D_2O$ dilution technique to estimate milk consumption of suckling piglets. Milk consumption of 50 individual piglets was estimated on four consecutive days by the $D_2O$ dilution method and for approximately 8 hours on both the second and fourth day by the traditional WSW method. The average milk intake of piglets estimated by the $D_2O$ dilution method was 45.0 g/hr and there were no significant differences between the four measurement period. The traditional weigh-suckle-weigh method provided a significantly lower estimate of milk consumption (36.8 g/hr). However correction for weight losses associated with milk suckling and weighing would increase the weigh-suckle-weigh estimate to a level similar to that determined by the $D_2O$ dilution method.

• Journal of Environmental Science International
• /
• v.7 no.6
• /
• pp.793-801
• /
• 1998

In this study, the Dilution Method is used to measure river discharge through the hydraulic model test. the dilution method is divided into Constant-Rate-Infection Method and Slug-Injection Method in the river discharge measurement techniques. When the dilution method is applied in the hydraulic model flume, it is analyzed that the estimated error of constant-rate-injection method is less than that of the slug-in-jection method, and the result shows that floodflow analysis is more efficient than lowflow analysis as compared observed discharge with calculated discharge. The result of statistical error analysis shows that the constant-rate-injection method is appropriate technique for the measurement of the river discharge. Therefore, the dilution method among the river discharge measurement techniques can be applied for the river basin which can't be measured with current meter or unsteady-flow regime in the urban-small drainage or hydraulic structure equipment area and can be obtained more exact results than any other discharge measurement techniques.

• Asian-Australasian Journal of Animal Sciences
• /
• v.3 no.2
• /
• pp.135-141
• /
• 1990

Two experiments were conducted to determine the validity of the deuterium oxide ($D_2O$) dilution method to estimate milk intake by pigs. A total of 39 piglets weaned from their dams 24 - 36 hours after birth and trained to drink from artificial nipples, were used for two experiments. Estimates of milk replacer consumption of individual piglets over 1, 3, 5 and 7 days were made by the $D_2O$ dilution method and by dissappearance. Milk intakes estimated by this $D_2O$ dilution method were significantly correlated ($R^2$ = 0.98-0.99) with milk intake measured by disappearance. The average difference between estimates by disappearance and estimates by the $D_2O$ dilution method were -1%, +0.5%, +0.5% and -2.1% for measurement period of 1, 3, 5 and 7 days respectively.

• Journal of Biosystems Engineering
• /
• v.31 no.5 s.118
• /
• pp.443-448
• /
• 2006

For development of an on-line monitoring unit of fermentation process, an auto dilution unit based on traditional chemical and biological analytical method was developed and the performance was evaluated. The dilution unit was constructed with two syringe pumps and flow direction change valves and fully automated. Total delivery volume of two pumps using distilled water was measured to confirm the operating stability And diluted concentrations of three substrate solutions (glucose, lactic acid, ethanol) were compared with a standard method with a high performance liquid chromatograph (glucose, lactic acid) and gas chromatograph (ethanol). Relative error values of total delivery volume of the pumps were below 3% and standard deviation values were 0.003 (n=5). Relative error values of diluted concentration of the dilution unit measurements were below 2% with 1/10 of dilution ratio and 70, $80{\mu}{\ell}$ of sample volume conditions for glucose and lactic acid, 1/30 of dilution ratio and $70{\mu}{\ell}$ of sample volume conditions for ethanol, respectively. In case of the ethanol, cause of the evaporative characteristics, the relative error values showed over 5% whole experimental conditions.

• Korean Journal of Veterinary Service
• /
• v.23 no.1
• /
• pp.19-28
• /
• 2000

There are several main antibacterial susceptibility tests, such as agar dilution method, broth dilution method and disk diffusion technique. Especially, for minimal inhibitory concentration (MIC) test, agar dilution method has been widely used. But that method is so complicated and bothering that it's difficult to treat a large amount of strains. On the other hand, modified broth dilution method(add 1% glucose and 0.018% phenol red as a pH indicator to broth) is fast and easy to perform. Most of all, it can visualize the result by color. The MICs of 22 antibiotics Including penicillins, aminoglycosides, cephalothin, chloramphenicol, lincomycin, ceftiofur, vancomycin and quinolones, erythromycin, colistin. sul-fadimethoxine, trimethoprim for arcanobacterium pyogenes 14 strains, actinobacillus pleuropneu-moniae 41 strains and pasteurella multocida 37 strains, which were collected from porcine during 1996 ∼ 1999, were determined by modified broth dilution method. Actinobacillus pleuropneumoniae was highly susceptible to all kinds of quinolones such as ciprofloxacin, enrofloxacin and norfloxacin and to all aminoglycosides, like gentamicin, apramycin, kanamycin and ampicillin, cephalothin and ceftiofur. But It was quite resistant to solfadimethoxin, colistin and vancomycin. Pasteurella multocida was found to have high susceptibility to ampicillin, cephalothin, chlorampenicol and gentamicin but had mid-degree susceptibility to other aminoglycosides. In addition, it was susceptible to norfloxacin and nalidixic acid, but not to newer fluoroquinolone like ciprofloxacin and enrofloxacin and it was resistant to colistin and kanamycin. Arcanobacterium pyogenes was highly susceptible to most of quinolones such as cipoofloxacin, enrofloxacin and norfloxacin and gentamicin and penicillin G. But it also obtained high resistance against the early quinolone, nalidixic acid and aminoglycosides such as amikacin, apramycin and kanamycin and erythromycin, chlorampenicol, tetracyclin and vancomycin.

• International Journal of Oral Biology
• /
• v.46 no.2
• /
• pp.94-97
• /
• 2021

The purpose of this study was to introduce a new in vitro method for evaluating the antimicrobial activity of toothpaste, reflecting the actual toothbrushing time and the dilution of toothpaste by salivation. We designed three experimental groups and one negative control group. The experimental groups were (1) 90 μL of toothpaste + 10 μL 1X phosphate-buffered saline (PBS, 9/10 dilution group), (2) 50 μL of toothpaste + 40 μL 1X PBS (1/2 dilution group), and (3) 25 μL of toothpaste + 65 μL 1X PBS (1/4 dilution group). During toothbrushing, saliva is continuously secreted into the oral cavity and the toothpaste concentration is diluted over time during toothbrushing. Therefore, the 1/2 and 1/4 dilution experimental groups were added. The negative control group was toothpaste diluted 20,000-fold with 1X PBS. Miracle Fresh Doctor toothpaste and Streptococcus mitis KCOM 1350, Prevotella intermedia KCOM 1107, Fusobacterium nucleatum subsp. polymorphum KCOM 1322, and Aggregatibacter actinomycetemcomitans KCOM 1306 were used as the toothpaste and target bacterial strains, respectively. The number of bacterial cells plated on agar plates in the negative control group was 1,000 CFU. If the number of colonies on the experimental group plate was less than one, the treatment was considered to have > 99.9% bactericidal activity. These results suggest that this new in vitro method for antimicrobial evaluation could be used as the standard method for testing the antimicrobial activity of toothpaste.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.1
• /
• pp.59-67
• /
• 2014

Purpose: The present study was aimed to compare the results of disinfection efficacy tested by membrane filtration method with dilution-neutralization method to develop the standard methods for evaluating disinfection efficacy of contact lens care products and to provide the result of disinfection efficacy of commercially available contact lens care products in domestic market. Methods: The results of disinfection efficacy against Staphylococcus aureus, Pseudomonas aeruginosa, Serratia marcescens, Candida albicans evaluated by membrane filtration method as a FDA standard and dilution-neutralization method as newly being a KFDA standard were compared and the disinfection efficacy of 16 multi-purpose solutions was further evaluated. Results: The disinfectants and contact lens care products having strong disinfection efficacy showed same results in both membrane filtration method and dilution-neutralization method. In case of contact lens care products having weak disinfection efficacy, the number of micro-organisms was not able to count since the colony was aggregated when evaluated by membrane filtration method. However, the number of micro-organisms was able to exactly count when evaluated by dilution-neutralization method. In addition, some commercially available contact lens care products did not meet disinfection standard and especially, their disinfection effect was often weak against Serratia marcescen and Candida albicans. Conclusions: It is concluded that dilution-neutralization method will be useful to evaluate disinfection efficacy since it is possible to count micro-organisms more precisely even with small amount of sample and check the results faster compared with membrane filtration method.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.427-434
• /
• 1995

Inductively coupled plasma mass spectrometry combined with the isotope dilution method is used for the determination of lithium. The isotope dilution method is based on the addition of a known amount of enriched isotope (spike) to a sample. The analyte concentration is obtained by measuring the altered isotope ratio. The spike solution is calibrated through so called reverse isotope dilution with a primary standard. The spike calibration is an important step to minimize error in the determined concentration. It has been found essential to add spike to a sample and the primary standard so that the two isotope ratios should be as dose as possible. Since lithium is neither corrosive nor toxic, lithium is used as a chemical tracer in the nuclear power plants to measure feedwater flow rate. 99.9% $^7Li$ was injected into a feedwater line of an experimental system and sample were taken downstream to be spiked with 95% $^6Li$ for the isotope dilution measurements. Effects of uncertainties in the spike enrichment and isotope ratio measurement error at various spike-to-sample ratios are presented together with the flow rate measurement results in comparison with a vortex flow meter.