• Elastomers and Composites
• /
• v.54 no.3
• /
• pp.225-231
• /
• 2019

Bio-based polyester polyol was synthesized via esterification between azelaic acid and isosorbide. After esterification, bio-based polyurethanes were synthesized using polyester polyol, 1,3-propanediol as the chain extender, and 4,4'-diphenylmethane diisocyanate, in mixing ratios of 1:1:1.5, 1:1:1.8, 1:1:2, and 1:1:2.3. The bio TPU (Thermoplastic Polyurethane) samples were characterized by using FT-IR (Fourier Transform Infrared Spectroscopy), TGA (Thermal Gravimetric Analysis), DSC (Differential Scanning Calorimetry), and GPC (Gel Permeation Chromatography). The mechanical properties (tensile stress and hardness) were obtained by using UTM, a Shore A tester, and a Taber abrasion tester. The viscoelastic properties were tested by an Rubber Processing Analyzer in dynamic strain sweep and dynamic frequency test modes. The chemical resistance was tested with methanol by using the swelling test method. Based on these results, the bio TPU synthesized with the ratio of 1:1:2.3, referred to as TPU 4, showed the highest thermal decomposition temperature, the largest molecular weight, and most compact matrix structure due to the highest ratio of the hard segment in the molecular structure. It also presented the highest tensile strength, the largest elongation, and the best viscoelastic properties among the different bio TPUs synthesized herein.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.532-544
• /
• 2023

Purpose: To identify and evaluate the risk of chemical fire causative substances by using thermal analysis methods (DSC, TGA) for the hazards and physical property changes that occur when newly used biofuels are mixed with existing fuels It is to use it for identification and evaluation of the cause of fire by securing data related to the method and the hazards of the material according to it. Method: The research method used in this experiment is the differential scanning calorimeter (DSC: Difference in heat flux) through quantitative information on the caloric change from the location, shape, number, and area of peaks. flux) was measured, and the weight change caused by decomposition heat at a specific temperature was continuously measured by performing thermogravimetric analyzer (TGA: Thermo- gravimetric Analyzer). Result: First, in the heat flux graph, the boiling point of the material and the intrinsic characteristic value of the material or the energy required for decomposition can be checked. Second, as the content of biodiesel increased, many peaks were identified. Third, it was confirmed through analysis that substances with low expected boiling points were contained. Conclusion: It was shown that the physical risk of the material can be evaluated by using the risk of biodiesel, which is currently used as a new energy source, through various physical and chemical analysis techniques (DSC + TGA).In addition, it is expected that the comparison of differences between test methods and the accumulation and utilization of know-how on experiments in this study will be helpful in future studies on physical properties of hazardous materials and risk assessment of materials.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.85-89
• /
• 2011

Waste water is disposed to sewage disposal plant by underground PE double wall pipes. Various processes have been introduced to join PE pipes, but most of these methods have many disadvantages such as costs, lack of reliability and difficulties in joining, etc. Recently butt welding has been paid much attention to joint PE pipes as this process has many advantages such as cost, safety and reliability. In this study, newly developed heat plate, a patent-pending heat plate with a groove, was used to butt-weld PE double wall pipes with different misalignment gaps to simulate real underground conditions, and the butt welding temperature of PE pipe was determined by thermal analysis (Thermal Gravimetric Analysis, Differential Scanning Calorimetry and Dynamic Mechanical Analysis). The resulting joining characteristics of double wall pipes were compared with those from a conventional heat plate, in terms of stiffness, flattening and leakage tests. The results from the stiffness and flattening test showed that there were no big differences between the butt-welded joints made from these two plates. From the leakage test, although PE pipes welded with a conventional heat plate did leak below the required test conditions (10 min. at 0.75kgf/cm2), the pipes welded with a patent-pending grooved heat plate did not show any leakage even at a pressure 1.5 times higher than the required conditions. It was noted that by utilizing a grooved heat plate more complete fusion at the pipe joints could be obtained, which in turn induced a high quality joints.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.123-128
• /
• 2001

This study was performed to find out variation of carbonation progress of agricultural hydraulic concrete structures along the used years with using Thermo Gravimetric analysis/Differential Thermal Analysis(TG/DTA) and Indicator(phenolphthalein). In this study some conclusions such as follows were derived. Firstly, The result that the age of structures and the content of $Ca(OH)_{2}\;and\;CaCO_{3}$ in concrete have proportional relationships was found in the method of TG/DTA. This relational functions could be used to estimate remain lifetime of structures, obtaining the limits of the content of $CaCO_{3}$ in concrete which reinforcement corrosion could be occurred with breaking protection cover of alkalinity. Second, if the result of strength, voids, permeability characteristics could be combined with this relational function this may be able to be used as a new more accurate assessment technique for the quality of concrete than current usual methods. Third, environmental affect could be more superintendent for concrete carbonation than the age of agricultural hydration structures. Forth, It is difficult to estimate the used year of agricultural hydraulic concrete structures with the carbonation depth measured by indicator method. Finally, the accuracy of this relational function could be decided to be upgraded with continue analysis for more structures.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.4
• /
• pp.321-330
• /
• 2020

The addition of a limestone filler(LF) to fill into the voids between cement and aggregate particles can reduce the cementitious paste volume. In previous studies, it has been found that the addition of LF to reduce the cementitious paste volume would substantially increase the compressive strength, and reduce the heat generation. This paper aim to evaluate the influence of LF contents on the hydration kinetics and compressive strength. Hydration kinetics were evaluate using heat of hydration, ignition loss and thermal analysis. The heat of hydration was measured using Isothermal Calorimetry. The degree of hydration was measured using ignition loss. Hydration product analysis was carried out by Thermal Gravimetric and Differential Thermal Analysis. The results show that the addition of LF reduces not only the initial setting time and heat of hydration peak, also degree of hydration and rate of strength development at early age increase with the addition of LF. It can be concluded the LF fills the pore between cement particles due to formation of carboaluminate, which may accelerate the setting of cement pastes.

• Journal of Energy Engineering
• /
• v.26 no.4
• /
• pp.74-83
• /
• 2017

Coal-fired power plants supply roughly 50 percent of the nation's electricity but produce a disproportionate share of electric utility-related air pollution. Coal combustion technology can facilitate volume reduction of up to 90%, with the inorganic contaminants being captured in furnace bottom ash and fly ash residues. These disposal coal ash residues are however governed by the potential release of constituent contaminants into the environment. Accelerated carbonation process has been shown to have a potential for improving the chemical stability and leaching behavior of bottom ash residues. The aim of this work was to quantify the volume of $CO_2$ that could be sequestrated with a view to reducing greenhouse gas emissions and stabilize the contaminated heavy metals from bottom ash samples. In this study, we used PC boiler bottom ash, Kanvera reactor (KR) slag and calcined waste lime for measuring chemical analysis and heavy metals leaching tests were performed and also the formation of calcite resulting from accelerated carbonation process was investigated by thermo gravimetric and differential thermal analysis (TG/DTA).

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.190-193
• /
• 2004

Two different diene monomers [dicyclopentadiene (DCPD) and 5-ethylidene-2-norbomene (ENB)] as self­healing agent for polymeric composites were microencapsuled by in-situ polymerization of urea and formaldehyde. The healing agents were investigated by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Exothermic reaction and glass transition temperature from DSC and storage modulus (G') and tan $\delta$ from DMA curves were analyzed for the samples cured for 5 min and 24 h in the presence of different amounts of catalyst. Micorcapsules were successfully formed for both diene monomers. Microcapsules containing the healing agent were manufactured and its thermal properties were characterized by thermo gravimetric analysis (TGA). Optical microscope (OM) and particle size analyzer (PSA) were employed to observe morphology and size distribution of microcapsules, respectively. Comparison of the two self-healing agents and their microcapsules with the two was made in this study.

• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.56-60
• /
• 2005

We studied fire properties of MOF(Metering Out Fit) insulation cover and field condition of 22.9kV power receiving system. $49.5\%$ of formal equipments were installed indoors, whereas $40.8\%$ of informal equipments were installed as H-type. Insulation treatment was not done at a $22.4\%$ ratio of main line($27.7\%$ of transformer, $70.2\%$ of COS, $10.4\%$ of MOF). Fire pattern analysis showed that the fire started at the secondary part of OC wire. In the result of DTA(Differential Thermal Analysis), normal cover showed exothermic reactions at $310^{\circ}C,\;399^{\circ}C\;and\;510^{\circ}C$ (endothermic reactions at $382^{\circ}C$). Whereas damaged cover showed exothermic reactions at $412^{\circ}C$(endothermic reactions at $389^{\circ}C$). In the result of TGA(Thermo Gravimetric Analysis), the thermal weight change of normal cover was similar compared to damaged cover. In the result of FT-IR analysis, normal cover showed absorption peaks at $3,024cm^{-l},\;2,921cm^{-l},\;1,600cm^{-1},\;1,492cm^{-1},\;1,451cm^{-1},\;1,154cm^{-l},\;1,027cm^{-1},\;906cm^{-1}$. Whereas, in case of tracked cover, the absorption peaks that were shown in normal cover disappeared and different absorption peak was shown at $966cm^{-1}$.

• The Korea Journal of Herbology
• /
• v.21 no.4
• /
• pp.149-158
• /
• 2006

Objectives : This study was carried out to characterize the 'Kaolinitum' used as mineral medicine before and after physical and chemical manipulation. Methods : The mineralogy of the original raw kaolinitumes with different localities was identified by X-ray diffraction analysis. The concentrations of major, minor and trace elements of samples, furthermore, measured by the X-ray fluorescence spectrometer (XRF) and inductively coupled plasma-mass spectrometer (ICP-MS). In order to understand the variety of kaolinitum after thermal treatment, the differential thermal analysis (DTA) and the thermo-gravimetric analysis (TGA) were carried out. Results : According to the result of X-ray diffraction analysis, the kaolinitumes are composed ofcalcite, alunite and quartz. Si and Al are the major ions and heavy metals such as Cd, Cr, Pb, Zn, As, Ni and Cu are included in the kaolinitumes as trace ions. The concentration of these metals in the samples decreased after physical and chemical manipulation. The weight of kaolinitum was also decreased at $500^{\circ}C$ and about $700^{\circ}C$during experiment of TGA. Conclusion : The results of this study can be used to provide the scientific basis of the medical usage of kaolinitum.

• Carbon letters
• /
• v.14 no.1
• /
• pp.34-39
• /
• 2013

Acrylonitrile (AN)-acrylamide (AM) copolymers were prepared by nitric acidic hydrolysis of homopolyacrylonitrile. The acrylamino group increased as a function of hydrolysis time, while crystallinity decreased. Differential scanning calorimetry and a thermal gravimetric analysis indicated that the acylamino introduced by acidic hydrolysis effectively enhanced the cyclization reaction at low temperature due to the change of the cyclization reaction mechanism. Char-yield of AN-AM copolymers also gradually increased with increasing hydrolysis time. The maximum char-yield was 49.48% when hydrolized at $23^{\circ}C$ in 65% nitric acid solution for 18 h, which was 30% higher than that of non-acidic hydrolysis of homopolyacrylonitrile. Simulation of the practical process also showed an increase of char yields, where the char yields were 55.43% and 62.60% for homopolyacrylonitrile and copolyacrylonitrile, respectively, with a hydrolysis time of 13 h.