• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.994-999
• /
• 2007

The particulate matters emitted by diesel locomotives cause serious air pollution in stations and railroad. There have been various attempt to reduce the air pollution from diesel bus or trucks. However, the air pollution from the diesel locomotives has been out of control because there has not any adaptable technology. In this study, a diesel particulate filter was developed and applied to the diesel locomotives. A 3,000 horsepower large-scale locomotive and a 1,500 horsepower middle-scale locomotive were used for the test of the filter. The particulate matter emissions before and after the treatment was monitored by a scanning mobility particle sizer and a dust monitor. As a result, it was observed that the particulate matters could be successfully removed from the emission gases by using the filter.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1405-1411
• /
• 2011

It is very often for the experienced diesel locomotive drivers to identify the proper replacing time for the fuel adjustment tube only based on their experience. Because of that, sometimes the locomotive's fuel is burned out due to the unnecessary torque. Or sometimes, the locomotive does not operate with its accelerating performance because the fuel is not supplied at the appropriate moment. Meanwhile, recent typical auto vehicles provide drivers with the average fuel efficiency and the instant fuel efficiency in real-time. By providing the real time display mentioned above, it is one of the good examples that those drivers, who had driven their cars not properly and used a lot of fuel with their bad driving habits, obtain the efficient driving pattern by continuous educating effect. Similarly, if the diesel locomotive provides the train driver with the optimal driving pattern within a certain driving section, it will be effective for fuel saving. It is possible to make the most effective driving pattern by performing the repeated trial running especially for the railway because the track's operating routes, its grades, and etc are relatively precise. This research analyzes the result data which was obtained by many times trial running on the identical section after equipping the fuel use measuring device to a certain test vehicle, and confirms the fuel saving effect depending on the driving pattern along the test section. At the same time, the research to establish the optimal driving pattern was progressed.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1315-1319
• /
• 2011

As government's policy is enacted to reduce greenhouse gas emission in transportation sector, railroad sector has to estimate amount of emission and propose feasible methods to reduce emission. To calculate accurate emission of railroad sector, we performed a study on the calculation model development for Tier 3 GHG emission factors. According to IPCC guide line, Tier 3 emission factor reflects individual characteristic of diesel locomotive. For this reason, we estimated GHG emission factor by stratified diesel locomotive and the result show difference of emission factor by notch changing. Therefore, the analysis of notch frequency during operation is required to develop Tier 3 emission factor, and we analysed a running pattern of diesel locomotive. As a result, idle and 8 notch consist about 70% of total running distance. In conclusion, the calculation model suppose that Tier 3 GHG emission factor is the sum of multiplied emission factor by weights in each notch. This result can contribute to Tier 3 emission factor calculation and reduction method development of emission in railroad sector by managing driving efficiency and technology development.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.969-974
• /
• 2002

Recently, many studies are performed according to increased interests about factory or room acoustics. In this study, the inside and environmental noise conditions of Diesel-locomotive load test building were investigated by multi-channel noise measurement system. In addition to this, the mitigation effects of environmental noise from this test building were analyzed using commercial software.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.652-659
• /
• 2000

The machine structure or parts has been arrive at a fracture, depend on crack by repeated load. Machine designer is estimate of fatigue strength in early stages the design for prevent fatigue fracture, then necessary its load history. This research study is using diesel locomotive in measurement of load history for fatigue design of rolling stock. The relation between velocity and amplitude of load history was found. We confirmed that the increase of velocity make to increase the magnitude of amplitude.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.385-390
• /
• 1999

In this paper, we investigated the wear rate, braking temperature and stopping distance of the composite brake shoe for diesel locomotive in the field test. The wear rate and braking temperature of the composite brake shoe would rather than cast iron. Also, the stopping distance of composite brake shoe is 450m at 100km/h. This result of field test shown that the density distribution of the composite brake shoe influence on wear rate.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.2
• /
• pp.133-143
• /
• 2003

Numerous evidence have been reported that fine particulate matters can play an important role in threatening human health. Recently concerns on fine particle pollution from various engines may require re-examination of particulate emission standards. The particles emitted by most diesel engines are mainly divided into their size ranges such as Dp< 50 nm and 50 nm< Dp< 1,000 nm. In this work, the number concentration and the size distribution of fine particles emitted from an exhaust manifold of a railroad diesel engine were measured under load test conditions using a scanning mobility particle sizer (SMPS). The fine particles observed were within the range of 7 to 304 nm under different load conditions with two different dilution ratios. The fine particles exhibited unique patterns showing bimodal shapes in size distribution.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1389-1396
• /
• 2008

There are many studies on the ride comfort for the train from the viewpoint of passenger. But there are only a few studies on the ride comfort for engineers in the locomotive. The railway has the track conditions, such as irregularities, rail joints, turnout, level crossing, transition curves and super-elevation ramps, which cause vibrations. Generally, the ride comfort for the train is evaluated by using the vibrations. In this study, vibration accelerations have been measured in the cabin rooms of locomotives, such as DL(Diesel-electric Locomotive), DHC(Diesel Hyduralic Car) and NEL(New-Electric Locomotive) when running on the Kyoungbu conventional line. And then, their ride comforts has been analyzed and evaluated by statistical method according to UIC 513R.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.2
• /
• pp.227-242
• /
• 2005

The aim of this study is to relieve the poor ventilation problem of the diesel locomotive engine load test building, located in an urban area. This paper evaluates the ventilation performances of the studied load test building based on the temperature measurement experiment and the computational fluid dynamics (CFD) during the engine load test. The temperature rise caused by the radiator blower of the building was turned out to be the main cause of disturbing the thermal conditions of the building. The indoor temperature distributions simulated by Fluent were validated with the temperature measurement results obtained from the studied building. The simulation results indicated that the comfort condition of this building was poor We suggested several remedial changes in the duct structure of this building for the improvement of the comfort conditions. In addition, a prototype drawing combining several improved design options was proposed. and then the simulation of the temperature distribution in the proposed prototype was performed. The result indicated that the indoor thermal condition of this proposed building was improved when compared with that of the current building.

• International Journal of Railway
• /
• v.1 no.2
• /
• pp.31-36
• /
• 2008

$DF_{21}$ diesel locomotive was designed to satisfy the requirement of Kunming Meter track and the 2Co self-guided radial bogie was used to suit the complex curve track. There are totally 12 locomotives was served on the track. The first two locomotives were devotion running on the track since April 2003, the wheel tread splling was occurred on the middle wheel set of the two locomotives after running nearly 150 thousands km on the track of the two locomotives at August 2004. The dynamic analysis was carried out to find the reason. The wheel set longitudinal vibration resonance phenomenon was existed on the locomotive dynamic performance, and this was caused by the too big longitudinal stiffness of the journal box bar on the middle wheel set. Wheel set longitudinal vibration resonance maybe an important reason of lead to wheel tread spalling. The corresponding mend methods were put forward from the point of view of wheel set longitudinal vibration resonance. All the wheel tread of the 12 locomotives on the middle wheel set were in good condition and not occurred the wheel tread spalling after the mend till December 2007 after 350 thousands km were finished. The mechanism of the wheel tread splling and corresponding mend method was discussed in detail in this paper.