• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.107-108
• /
• 2006

High $J_c$ $YBa_2Cu_3O_x$, superconducting films were fabricated by MOD method using fluorine-free dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. DCA-MOD precursor solution was coated on a single crystal (001) $LaAlO_3$(LAO) substrate by a dip coating method with a speed of 25 mm/min. Coated films were calcined at lower temperature up to $500^{\circ}C$ and Conversion heat treatment was performed at various temperatures of $780{\sim}810^{\circ}C$. SEM observations showed that films have very dense microstructures for the films prepared at the temperature higher than $800^{\circ}C$ regardless of diluting solvent; methanol or 2-methoxyethanol. A High critical current density ($J_c$) of 1.28 $MA/cm^2$ (@77 K and self-field) was obtained for the YBCO film prepared using 2-methoxyethanol as a solvent.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.288-293
• /
• 2013

Crosslink characteristics of maleic anhydride-grafted EPDM (MAH-g-EPDM)/zinc oxide composite were investigated by weight losses after dichloroacetic acid (DCA)/toluene cosolvent extraction at different temperatures and by measurement of crosslink densities. The chemical changes were analyzed using attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR). The weight losses by extraction at high temperature ($90^{\circ}C$) were remarkably greater than those at room temperature and those by DCA/toluene cosolvent extraction were greater than those by toluene one by more than 5 times. The crosslink densities were measured after the solvent extraction, and the second crosslink densities were higher than the first ones. The first crosslink density was lower when the extraction temperature was high, and it was much lower for the toluene extraction than for the DCA/toluene cosolvent extraction. The second crosslink density of the sample extracted with DCA/toluene cosolvent was greater than that extracted with toluene. The extracted components were depending on the extraction solvents and temperatures, for example; only strong crosslinked networks were remained when extracting with DCA/toluene cosolvent at high temperature, while only uncrosslinked polymer chains were extracted when extracting with toluene at room temperature. Therefore, crosslink characteristics of the MAH-g-EPDM/zinc oxide composite can be analyzed by comparison of the extracted components according to the extraction solvents and temperatures and by measurement of successive crosslink densities.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.152-157
• /
• 2006

New precursor solution with dichloroacetic acid (DCA) was developed for fabricating high $J_c$ REBCO film. DCA based-precursor solution was coated on $LaAlO_3$(001) substrate by dip coating method. Processing parameters such as oxygen partial pressure, water vapor, ramping rate and pyrolysis temperature were controlled in order to obtain a good epitaxial film. The film with thickness of 0.5 micrometer was obtained by single coating and no crack was observed at calcined films. Oxygen partial pressure was controlled in the range of $100{\sim}1,000$ ppm and conversion heat treatment was carried out at the temperature range of $705-765^{\circ}C$. A critical transition temperature ($T_c$) of 90 K and a critical transport current density ($J_c$) of $>0.5\;MA/cm^2$ (77 K and self-field) were obtained for the GdBCO film. It is thought that fluorine-free MOD solution using DCA is promising precursor solution for fabricating high quality REBCO films.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.59-64
• /
• 2006

High $J_c\;YBa_2Cu_3O_x$ superconducting films were fabricated by MOD method using fluorine-free dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. Coating solutions were prepared by dissolving Y-, Ba- and Cu-acetates in DCA solvent followed by drying in rota vapor to obtain the blue gel that is diluted in methanol and 2-methoxyethanol for adjusting the cation concentration. DCA-MOD precursor solution was coated on a single crystal(001) $LaAlO_3(LAO)$ substrate by a dip coating method with a speed of 25 mm/min. Coated films were calcined at lower temperature up to $500^{\circ}C$ in flowing oxygen atmosphere with a 7.2% humidity. Conversion heat treatment was performed at various temperatures of $780{\sim}810^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. SEM observations showed that films have very dense microstructures for the films prepared at the temperature higher than $800^{\circ}C$ regardless of diluting solvent; methanol or 2-methoxyethanol. X-ray diffraction analysis showed that YBCO grains grew with a (001) preferred orientation. A High critical current density($J_c$) of 1.28 $MA/cm^2$(@77 K and self-field) was obtained id. the YBCO film prepared using 2-methoxyethanol as a solvent.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.186-192
• /
• 2007

High $J_c\;YBa_2Cu_3O_{7-x}$ superconducting films have been fabricated $LaAlO_3(100)$ substrate by MOD method using dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. Heating rate was varied in order to optimize the calcination heat treatment condition in DCA-MOD method. Coated films were calcined at lower temperature up to $500^{\circ}C$ in flowing humid oxygen atmosphere. The heating rate was calcined from $13.3^{\circ}C/min\;to\;0.28^{\circ}C/min$. Conversion heat treatment was performed $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. Surface and cross sectional SEM microstructures showed that particle sizes were increased with heating rate at a calcination step. The amount of pores was increased with heating rate in the calcined films. Dense microstructure and sharp texture were developed in an YBCO films after conversion heat treatment. A high critical current density (Jc) of $1.26MA/cm^2$ (@77 K and self-field) was obtained for the YBCO film which was prepared with a heating rate of $0.28^{\circ}C/min$.

• 한국초전도학회:학술대회논문집
• /
• v.16
• /
• pp.37-37
• /
• 2006

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.05a
• /
• pp.45-52
• /
• 1995

The photocatalytic activity of TiO$_2$ was investigated as a function of added amount of Nb$_2$O$_{5}$, heat treatment temperature and the decomposition rate of 1 mM dichloroacetic acid(DCA). Mixed oxides of TiO$_2$ and Nb$_2$O$_{5}$ was prepared by the sol-gel process. The addition of Nb$_2$O$_{5}$ into TiO$_2$ has deleterious effect on the decomposition rate of DCA, which was decreased as the amount of Nb$_2$O$_{5}$ was increased. The excess electrons due to the doping of Nb$_2$O$_{5}$ into TiO$_2$ can promote the reduction process instead of oxidation or recombination rate with electron holes. The most efficient photocatalyst was the one heat treated at 40$0^{\circ}C$ for an hour as far as the heat treatment temperature is concerned. The lower the pH of the solution, the higher the quantum yield.tum yield.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.05a
• /
• pp.31-40
• /
• 1995

The degradation of aqueous chlorinated compounds such as trichloroethylene (TCE), tetrachloroethylene (PCE) and dichloroacetic acid (DCA) to $CO_2$ and HCl was accomplished in the presence of UV light and suspended TiO$_2$ slurries. The decomposition of chlorinated hydrocarbons at 253.7 m irradiation was more effective than that at 360 nm irradiation. Our results show that 253.7 nm irradiation alone can be used for decomposing some chlorinated hydrocarbons such as PCE and TCE.

• Korean Journal of Materials Research
• /
• v.6 no.3
• /
• pp.282-290
• /
• 1996

광화학 반응의 초기 유발을 위한 광촉매로 TiO2가 가장 널리 알려져 있으며, 기존의 상품보다 광촉매 활성도가 높은 촉매를 얻기 위해 Sol-Gel법을 이용하였다. TiO2 광촉매 제조를 위하여 전구체로서 Tetra-eth해-ortho-titanate(TEOT)를 이용하여 xerogeol 분말을 얻었으며, 광화학 반응의 효율을 측정하기 위해 분해대상 물질을 Dichloroacetic acid(DCA)로 선정하였다. 순수 titania 졸을 얻기 위한 최적조건은 알콕사이드 1몰당 물 40몰, 산 0.05몰이었고 pH의 범위는 3.3-3.6이었으며 Hexylene Glycol(HG)의 첨가량은 1몰임을 알 수 있었다. BET-N2방법을 이용하여 표면적을 측정한 결과 물/알콕 사이드의 몰비가 40-80범위에서 비표면적이 급격히 증가되어 DCA 의 광분해율도 증가하였으며, 몰 40몰을 첨가 후 졸-겔법으로 제조한 분말을 40$0^{\circ}C$에서 1시간 열처리한 anatase phase의 TiO2가 최고의 광분해 효율인 약 21%를 보였다. 이는 상업용으로 가장 효율이 높은 Dagussa P-25의 DCA 분해 효율보다 2배 정도 높은 것으로 나타났다.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.2
• /
• pp.99-109
• /
• 2006

In order to obtain the maximum flame retardancy as well as the minimum deterioration of physical properties of PU flame-retardant coatings, chlorine and phosphorus functional groups were introduced into the pre-polymer of modified polyesters. In the first step, the tetramethylene bis(orthophosphate) (TBOP) and neohexanediol dichloroacetate (DCA-adduct) intermediates were synthesized. In the second step, 1,4-butanediol and adipic acid monomers were polymerized with the two kinds of intermediates to obtain copolymers. The modified polyesters containing chlorine and phosphorus (ATBA-10C, -20C, and -30C) were synthesized by adjusting that the content of phosphorus compound was fixed as 2wt% and the contents of chlorine compound (dichloroacetic acid) were varied as 10, 20, and 30wt%. Average molecular weight and polydispersity index of the preparation of ATBAs were decreased with increasing DCA content because of the increase in hydroxyl group that retards reaction.