• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.935-944
• /
• 1987

The surface rolling, one of the plastic working processes, provides good surface roughness with the reduction of diameter and the increase of surface hardness. In this study three Nachi 6000ZZ bearing were used for surface rolling on ductile cast iron. The results obtained are as follows; (1) The good surface roughness can be obtained with roller surface radius of curvature of 24mm after the 2nd rolling. (2) The surface roughness of ductile cast iron was 0.48.mu.mRmax by the contact pressure of 140kgf/mm$^{2}$ and surface hardness was Hv 395 with roller surface radius of curvature of 24mm after the 2nd rolling. (3) The reduction of specimen diameter of ductile cast iron were -12.8.mu.m due to rolling. (4) Within the diameter variation of -11.mu.m, surface roughness and surface hardness were increased, but at the range of exceeding -14.mu.m of the diameter variation the surface roughness became worse and the surface roughness became worse and the surface hardness was increased. (5) Dynamic contact area was about 25% to 30% of static contact area. The calculated contact pressure showed a good agreement with the experimental contact pressure.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.297-301
• /
• 2007

The blades of supersonic turbines with low aspect ratio are usually designed to have the same cross sectional shape in radial direction. The profile diameter definition of turbines may lead to produce unintended flow passage area variations resulting performance degradation. In this paper, the effects of profile diameter definition on the supersonic impulse turbine performance have been investigated. Computational results of three different profile diameters are compared. It has been found that flow passage area variation can be achieved according to designer's intention when blade profile is defined at rotor tip diameter. Furthermore, the turbine blade profile defined at rotor tip showed better performance than the others.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.239-242
• /
• 2008

Combustion Characteristic with initial port-diameter of fuel was studied in hybrid propulsion system using cylindrical single port-grain. In order to understand a variation of combustion characteristic with initial port-diameter, experimental studies were performed with the GOX and $GN_2O$ as oxidizer, and PE as fuel. As results, burning rate decreased with increase of initial port-diameter of fuel. And the variation of burning rate with using $GN_2O$ is smaller than using GOX.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1089-1092
• /
• 2001

In the stereolithography process, build parameters are laser power, scan velocity, scan width, bean diameter, layer thickness and so on. These values are determined according to product accuracy and build time. Build time can be reduced by improving of scan velocity, laser power, layer thickness, hatching space and so on. But variation of these parameters influence part accuracy, surface roughness, strength. This paper observed cure properties in various beam diameter. In order to examine these, relationships of scan velocity and cure depth, scan velocity and cure width according to various beam diameter in one scan line are measured. And cure thickness is measured according to beam diameter and scan velocity in scan surface of one layer. For reduction of build time, beam diameter and scan velocity is proposed in stereolithography process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.250-258
• /
• 2010

A numerical analysis of reactive flow in a liftoff flame is accomplished to elucidate the characteristics of flame propagation velocity and volume integral of reaction rate with the variation of nozzle diameter and fuel injection flow rate in a liftoff flame consisted with fuel rich region, fuel lean region and diffusion flame region. The increase of fuel injection velocity enhances flame propagation velocity for the selected three nozzle diameter(d=0.25, 0.30, 0.35mm), but its effect on the flame propagation velocity is not much greater than 4.3%. The increase of fuel flow rate is directly and linearly related with the volume reaction rate and so the volume reaction rate, not the flame propagation velocity, might be considered to accommodate the variation of fuel flow rate in a liftoff flame.

• Journal of Powder Materials
• /
• v.29 no.4
• /
• pp.314-319
• /
• 2022

The effect of the laser beam diameter on the microstructure and hardness of 17-4 PH stainless steel manufactured via the directed energy deposition process is investigated. The pore size and area fraction are much lower using a laser beam diameter of 1.0 mm compared with those observed using a laser beam diameter of 1.8 mm. Additionally, using a relatively larger beam diameter results in pores in the form of incomplete melting. Martensite and retained austenite are observed under both conditions. A smaller width of the weld track and overlapping area are observed in the sample fabricated with a 1.0 mm beam diameter. This difference appears to be mainly caused by the energy density based on the variation in the beam diameter. The sample prepared with a beam diameter of 1.0 mm had a higher hardness near the substrate than that prepared with a 1.8 mm beam diameter, which may be influenced by the degree of melt mixing between the 17-4 PH metal powder and carbon steel substrate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.667-670
• /
• 2002

Uniform metal-droplet deposition using laser is analyzed. Using the variation principle and modeling the semi-solid phase as a non-Netwonian slurry, this model can greatly save the computational expenses that conventional numerical procedures have suffered from. The simulation results revealed that the developed model could reasonably describe the collision behavior of molten metal with solid surface. Simulations were made with variation of the falling distance and time.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.4
• /
• pp.449-456
• /
• 2011

Eighteen different biometric traits in 407 Kankrej cows from their breeding zone, i.e. Palanpur district of Gujarat, India, were recorded and analyzed by factor analysis to explain body conformation. The averages of body length, height at withers, height at shoulder, height at knee, heart girth, paunch girth, face length, face width, horn length, horn diameter, distance between horns, ear length, ear width, neck length, neck diameter, tail length with switch, tail length without switch and distance between hip bones were $123.44{\pm}0.37$, $124.49{\pm}0.28$, $94.68{\pm}0.30$, $38.2{\pm}0.14$, $162.56{\pm}0.56$, $178.95{\pm}0.70$, $44.09{\pm}0.10$, $15.91{\pm}0.05$, $42.47{\pm}0.53$, $26.07{\pm}0.19$, $13.34{\pm}0.08$, $31.24{\pm}0.12$, $16.10{\pm}0.05$, $50.63{\pm}0.18$, $73.21{\pm}0.32$, $111.62{\pm}0.53$, $89.34{\pm}0.34$ and $17.28{\pm}0.10\;cm$, respectively. The correlation coefficients between different traits ranged from -0.806 (horn diameter and distance between horns) to 0.815 (heart girth and paunch girth). Most of the correlations were positive and significant. Factor analysis with promax rotation with power 3 revealed three factors which explained about 66.02% of the total variation. Factor 1 described the cow body and explained 38.89% of total variation. The second factor described the front view/face of the cow and explained 19.68% of total variation. The third factor described the back of the cow and explained 7.44% of total variation. It was necessary to include some more variables for factor 3 to obtain a reliable estimate of the back view of the cow. The lower communities shown for distance between horns, horn diameter, ear width and neck diameter indicated that these traits did not contribute effectively to explaining body conformation and can be dropped from recording, whereas all other traits are important and needed to explain body conformation in Kankrej cows. The result suggests that principal component analysis (PCA) could be used in breeding programs with a drastic reduction in the number of biometric traits to be recorded to explain body conformation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.1
• /
• pp.64-70
• /
• 2023

In this study, reliability tests of torsion control expansion anchors according to drill bit diameters were performed. The standard deviation and coefficient of variation of the anchor were reviewed through the tests for each variable, and the results were compared and evaluated with the standard test results. As a result of the reliability test of the M12 and M16 anchors with 1.04 times the drill bit diameter, they were within 20% of the ultimate tensile load permissible standard coefficient of variation. It was found that the pulling-out performance of the anchor installed in the large hole was sufficiently secured. However, it was found to be about 253% and 210% of the design strength, indicating that the pulling performance of the anchor installed in 1.04 times the drill bit diameter was sufficiently secured. As a result of the reliability test of the M12 and M16 anchors with 1.02 times the drill bit diameter, the value of the coefficient of variation of the ultimate tensile load limit was within 20%, which satisfies the test standard. It was shown to be about 136% and 168% of the design strength, indicating that the pulling-out performance of the anchor installed in 1.02 times the drill bit diameter is sufficiently secured.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.5
• /
• pp.499-506
• /
• 2013

Heat-treatment is one of the core technologies to enhance various characteristics such as strength, hardness, toughness, abrasion resistance and fatigue resistance for the mold material. This paper focuses on characteristics of the laser heat-treatment according to the cylindrical bar diameter variation in case of the SM45C. From the results of the experiments, it has been observed that the maximum hardness is 744Hv when the power is 1630W and the travel of laser is 0.5m/min. And then, the hardness width, depth and microstructure were observed for characteristics. Finally, when the cylindrical bar diameter size grow, the hardness width decrease whereas hardness depth increase.