• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.52-58
• /
• 1998

The spray characteristics of air-assisted fuel injection and its effects on the engine combustion was investigated in this study. The atomization characteristics of a Bosch fuel injector inserted into the air-assist adapter were measured using particle motion analysis system. Droplet size decreased with air supplied and fine spray with below $60\mu\textrm{m}$ of SMD was acquired under the conditions of air-assist pressure over 0.5bar. The lean combustion performance of a 1.8L DOHC engine equipped with air-assist adapters was tested on the dynamometer. When the assistant air pressure is 1.0bar, lean limit recorded the highest value, and CO, HC emissions were decreased at the pressure over 1.0bar.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.384-394
• /
• 2005

Important characteristics of impinging sprays intersected by a strongly convective gaseous cross flows were experimentally investigated. The breakup processes due to different Weber and Reynolds numbers of liquid and gas streams were visually examined with quantitative measurements of breakup lengths, penetration heights, and droplet sizes. Snapshot images and spay data evidenced that, at lower jet Reynolds number the breakup processes portrays the atomization profiles similar to typical column breakup of single orifice jet. At higher jet Reynolds numbers, disintegration of jet stream is significantly expedited by strong momentum transported from strongly convective gaseous stream. The breakup length and penetration height decreased as the convective flow increase. From the bottom the wall up, the SMD measured the centerline increase. The maximum SMD appeared the top of the SMD distribution

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.10
• /
• pp.119-127
• /
• 2021

Small drops in gas cause some problems for downstream equipments such as turbine, compressor and etc. In some cases, we are obliged to remove hazardous liquid mist from gas. In order to remove water or other liquids from the gas, there are some equipments like mesh mist eliminator and vane-plate mist eliminator. oil mist filter is a kind of liquid eliminator equipments used to remove the liquid with 1-10um droplet diameter from the gas. In this paper is determine the factors affecting the oil mist filter efficiency using CFD. length and angle of the filter were considered and the results and compare the results of the efficiency tests, showed error of less than 3%. optimum filter can remove more than 87.3% between 1 and 10um of oil mist.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.395-406
• /
• 2005

Important characteristics of swirl sprays intersected by a strongly convective gaseous cross flows were experimentally investigated. The breakup processes due to different Weber and Reynolds numbers of liquid and gas streams were visually examined with quantitative measurements of breakup lengths, penetration heights, and droplet sizes. Snapshot images and spray data evidenced that, at lower jet Reynolds number the breakup processes portrays the atomization profiles similar to typical column breakup of single orifice jet. At higher jet Reynolds numbers, disintegration of jet stream is significantly expedited by strong momentum transported from strongly convective gaseous stream. The breakup length and penetration height decreased as the convective flow increase. From the bottom the wall up, the SMD measured the centerline first increases and then decreases before again increasing.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.1
• /
• pp.46-51
• /
• 2009

This paper presents results from field studies carried out to monitor off-target droplet movement of endosulfan insecticide applied to the Korea chestnut tree area. As a results, mean airborne drift values were recorded 25m as average from downwind of a single flight line(sample line) in mountain terrain and mean effective swath width was recorded 19.5m as average in a plain. In terms of characteristics of geography of Korea aerial application is mainly carried out in mountain terrain. The equipment, weather conditions, and appropriate aerial spray technic are required for effective aerial application. In particular, the pilot can get effective results when he only sprays with consideration of environment factors since there is much turbulence in mountain terrain. Eventually, the most effective factor of droplets drift is to estimate the local weather conditions exactly.

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.13-21
• /
• 2001

The effect of water spray for the fire sprinkler depends on droples distribution over maximum possible floor area. The present study are carried out for the characteristics of water spray and droplets experimentally and numerically km two fire sprinkler heads which are CHM head and CHl heal CHl head is self-production and CHl head is widely used up to date. As the result of using CHM head, water spray and droplets are distributed over large area because CHM head has smooth surface and non-flamed shape. When the pressure of fire sprinkler head is low, SMD(sauter mean diameter) is large and when the pressure of fire sprinkler head is high, SMD is small.

• Journal of ILASS-Korea
• /
• v.27 no.1
• /
• pp.26-35
• /
• 2022

Electrospray is a method of atomizing fluid using high voltage supply and capable of generating continuous flow and coherent size of droplets. Electrical system and properties of fluids has enabled electrospray to have various spray modes. However, its studies have been confined only in Cone jet, which is more stable and easier to manipulate droplets' size than other spraying modes. Therefore, it is necessary to investigate and compare other spraying modes based on experimental parameters and physical properties of fluids. This research paper identified nine different spray modes. It was found out that Sauter Mean Diameter (SMD) is proportional to flow rate of fluids and maximum difference among spray modes was 1.7 times. On the other hand, SMD standard deviation had low variations on specific flow rates of fluids. Pulsed jet mode recorded the largest SMD standard deviation, while Spindle recorded the lowest.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.467-473
• /
• 1996

Ultrasonic energy was applied for atomizing rice-bran oil which is a highly viscous bio fuel. Six different nozzles, an injection simulator, and an ultrasonic generator system were designed and constructed for the experiment. An immersion liquid method was used for the measurement of injection droplet sizes. The characteristics of injection droplets was investigated with respect to the numbers of the droplets with diameters ranging from 5$\mu$m 50$\mu$m and to the Sauter mean diameter. The results showed that the ultrasonic energy was effective for the improvement of the atomization of the injection droplets for all the factors such as type of nozzles, nozzle opening pressures, and collection distances.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.240-243
• /
• 2008

An experimental study was conducted to understand spray characteristics of rotating fuel nozzle by using high speed rotational system. The experimental apparatus consist of a fuel injection system, high speed rotational system, and acrylic case. The test is performed with several diameters and number of injection orifices. Spray characteristics such as droplet size and velocity are measured by PDPA(Phase Doppler Particle Analyzer). From the test results, we could understand the spray characteristics of rotating fuel nozzle with orifice number and diameter.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.10
• /
• pp.2690-2698
• /
• 1995

Fuel atomization and mixture formation in an gasoline engine has influence on the engine performance and pollutant emission. The throttle valve installed in an intake system plays a greater role in control of mixture quantity in accordance with engine drive condition. In this study, the characteristics of secondary atomization developed at the downstream of the valves were observed using an image processing method. Two major kinds of valves, solid and perforated ones, are chosen in order to compare the valve performance with the experimental parameters of air flow rate, valve opening angle, and valve shapes. For the perforated valve, we can obtain the relatively small sized droplets, and nearly uniformed and dense distributed sprays with low loss coefficient than for the solid valve.