• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.8-13
• /
• 2014

Currently it is major problem of electric railway with increasing drive speed such as the arc generated by the pantograph detachment and the distortion current in the motor-block high speed switching. When physical contact between the pantograph and the catenary line is separated, the pantograph detachment arcing occurs and it makes up the conductive noise to the return feeder. We made the EMTP modeling of the railway traction system and the pantograph arc by circuit elements and switches. The influence of pantograph detachment frequency is investigated by changing some frequencies. The over-current occurs in each detachment and it oscillates some time at beginning and stabilizes gradually. The magnitude of over-current is decided by instantaneous value of existing traction return current. If the detachment occurs at a point of peak value or distortion current, the over-current will be more harmful to the power systems connected with the return feeder and will become to arise with increasing detachment frequency.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.656-665
• /
• 1993

Two types of baby corn silk detachment systems called fixing and moving baby corn and based on applying frictional force on the silk were developed and evaluated. In the fixing mode the baby corn was fixed on a pin and a hollow frictional cylinder was moved concentrically and vertically along the baby corn towards the branch end. In the moving mode the baby corn was forced vertically towards the tip to pass through the same silk detachment cylinder. Traveling speeds of the detachment cylinder and the baby corn were 44.5 and 166.9 mm/s. In the fixing mode at silk moisture content of 91 % (w.b) silk detachment efficiencies at low and high speeds were 99.1 and 99.2%. The silk detachment efficiencies in the moving mode at low and high speeds were 96.6 and 98.5%. Damaged baby corn at low speed was less than at high speed in both modes. Minimum damage was nil in the fixing mode at low speed and the maximum was 47.5% in the moving mode at high speed. The damaged was due to ovaries r moval at the base near the joint between the baby corn and the branch.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.87-92
• /
• 2013

In high-speed train, the EMI is generated by pantograph detachment and switching device of motor-block. Especially, the conductive noise flows through rail as return feeder influences unintended results to sub-station, transformer, etc. These phenomena were investigated by PSIM circuit analysis tool and each part of railway system is modeled by circuit elements and switching devices. Consequently, the distorted wave in return feeder current occurs by the high speed switching frequency, and the overvoltage is applied by the pantograph detachment. Also the distortion of return current is high in starting point and it decreases from the proximity of a starting point ro the end of terminal.

• Current Research on Agriculture and Life Sciences
• /
• v.21
• /
• pp.23-29
• /
• 2003

Worldwide consumption of vegetable soybean bas been increasing recently, hence it is necessary to produce good quality of soybean in our farms. In the process of vegetable soybean production threshing and seperation work accounts for about 80% of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which measure the physical properties and investigate the detachment forces. Also, We calculated the minimum speed of threshing cylinder. The result are as follows; 1. The average length of soybean stem is 68.2cm. 2. The length of soybean pods are seen as 61.3mm for 3 grain, 52.6mm fer 2 grains and 41.0mm fer 1 grain 3. The widths of soybean pods are seen as 14.1mm fer 3 grain, 13.8mm fer 2 grains and 13.4mm fer 1 grain. 4. The weights of soybean pods are seen as 4.1grams for 3 grains, 2.7grams for 2 grains and 1.4grams for 1 grain. 5. The average detachment forces of pods are seen as 1.5kgf for 3 grains, 1.2kgf for 2 grains and 0.8kgf for 1 grain respectively For 1 grain, the detachment force of pods ranges from 0.2kgf to 1.4kgf. For 2 grains, the minimum detachment force of pods is seen as 0.6kgf and the maximum one is seen as 2.5kgf. For 3 grains, the minimum detachment force of pods is seen as 0.7kgf and the maximum one is seen as 2.7kgf. 6. The minimum speed of threshing cylinder is shown 6.83m/s.

• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.236-240
• /
• 2005

In order to prepare for the suitable surfaces of implants or medical devices, quantitative evaluation of adhesion between cells and biomaterials is essential. To better understand adhesion formation between cells and biomaterials, we used the cytodetachment technique which measures the adhesive force of a single cell through changing the, culture time and detachment speed. The results showed that the adhesive force could be affected by the culture time of cells on the surface of materials and the detachment speed. Moreover, there was a large discrepancy among the adhesion strength measured by similar techniques conducted on the different cells and substrates. It can be 'concluded that the variation of the force measurement technique can seriously alter the level of the force required to detach a cell on the surface of materials.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.89-96
• /
• 2002

The trend of consumption of vegetable soybeans is increasing because they are recognized as the clean vegetable. The works requiring the most intensive labor are threshing and seperation ones, and they form about 80% of total labour for vegetable soybeans production. It is necessary to develop the vegetable soybeans-thresher for the sake of cost down of vegetable soybeans production. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which control the speed of threshing cylinder and the teeth gap and investigate the detachment forces. The result are as follows ; The ratio of un-threshed soybeans-pod to stem after threshing work is decreasing as the threshing cylinder speed increases: 0.0% and 2.8% at 55m/s and 18m/s of threshing cylinder speed respectively. Also the ratio of un-threshed soybeans-pod to stem is shown as 2.0% below in the condition of 64~160mm of teeth gap and over 28m/s of threshing cylinder speed. The damaged pod ratio of detached soybeans after threshing work is decreasing as the threshing cylinder speed increases: 4.8% and 1.3% at 55m/s and 18m/s of threshing cylinder speed respectively. The minimum damaged pod ratio of detached soybeans are shown as 1.0%, 1.5% and 1.9% at 18m/s, 28m/s and 37m/s of threshing cylinder speed respectively. The average detachment forces of pods are shown as 1.5kg$_{f}$ for 3 grains, 1.2kg$_{f}$ for 2 grains and 0.8kg$_{f}$ for 1 grain respectively. The maximum detachment force of pod is shown as 2.7kg$_{f}$ for 3 grains. grains.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.05a
• /
• pp.159-159
• /
• 1999

Application of the macro layer dryout model has been performed to predict CHF at inclined plates. For the identification of the detachment frequency of coalesced bubble, experiments have been performed with high-speed motion analyzer and bubble behaviors at inclined plates have been investigated. Based on the observed bubble behaviors, the detachment frequency of the coalesced bubble is measured and linear relations between detachment frequency and heat flux have been developed. In the case of 60$^{\circ}$ and 90$^{\circ}$ inclined plate, the detachment frequency decreases with the increase of heat flux. However, opposite trend has been identified in $30^{\circ}$ in-clined plate: the detachment frequency increases with the increase of heat flux. Using the cor- relation of macro layer thickness suggested by Haramura & Katto and the extrapolation of the identified linear relations, CHFs at different conditions have been predicted. According to the prediction results, CHF values are well predictable.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.30-39
• /
• 2014

The trajectories of PCB(Printed Circuit Board) particles in the corona discharge electrostatic separation was simulated. The PCB particles are prepared by crushing bare board, which disassembled from electronic components, consist mostly of copper and FR-4(Flame Retardant Level-4) Firstly, a model was established for calculating of detachment points of PCB particles from the rotating electrode in separator. The model of detachment points was derived from equilibrium of force such as gravity force, centrifugal force, electrostatic force. The trajectories of particles after detachment was calculated by acceleration derived from time-integrating method of motion equation. In this simulation, particle size, supplied voltage, rotation speed of rotating roll electrode and angle of induction electrode were adopted as variables. While the trajectories of FR-4 particles were affected by all variables, rotation speed of rotating roll electrode was dominant variables affecting trajectories of copper particles.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.94-100
• /
• 2002

During the last years, great progress has been made in the fields of welding power sources and filler materials for the MIG-welding of magnesium alloys. This advice resulted in a better welding process, md, therefore, in highly improved welding results. Furthermore the gap between short-circuiting- and spray-arc-trunsfer could be closed by the triggered short-circuiting- and the short-circuiting-arc with pulse overlay. A crucial contribution to the welding process is the energy input into the filler material. Many problems result from the physical properties of magnesium, for instance its narrow interval between melting point 600$^{\circ}C$ and vaporization point 1100$^{\circ}C$. The energy input into the filler material has to be regulated in such a way that the wire will melt but not vaporize. For th is reason, special characteristics of power sources hue been examined and optimized with the help of high-speed-photographs of the welding process with particular consideration of the drop detachment. An important improvement of the weld seam profile has been achieved by using filler material of only 1.2 mm in diameter. The experiments hue been made with 2.5 mm thick extruded profiles of AZ31 and AZ6l. The results of tensile testing showed strength values of 80 to 100% of the base metal. B ending angles up to 60$^{\circ}$ have been reached. The fatigue strength under reversed bending of the examined magnesium alloys after welding reaches 50% of the strength of the base metal. When the seam reinforcement is ground of the fatigue strength can be raised up to 75% of the base metal.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.4
• /
• pp.337-346
• /
• 2014

This study aimed to understand the mode characteristics of a droplet subject to periodic forced vibration and the detachment of a droplet placed on a plate surface. An surface was coated with Teflon to clearly observe the behavior of a droplet. The contact angle between the droplet and surface and the hysteresis were found to be approximately $115^{\circ}C$ and within $25^{\circ}C$, respectively. The coating process was performed in a clean room that had an environment with a low level of contaminants and impurities such as air dust, detergents, and particles. To predict the resonance frequency of a droplet, theoretical and experimental approaches were applied. Two high-speed cameras were configured to acquire side and top views and thus capture different characteristics of a droplet: the mode shape, the detachment, the separated secondary droplet, and the waggling motion. A comparison of the theoretical and experimental results shows no more than 18 discrepancies when predicting the resonance frequency. These differences seem to be caused by contact line friction, nonlinear wall adhesion, and the uncertainty of the experiment. For lower energy inputs, the contact line of the droplet was pinned and the oscillation pattern was axisymmetric. However, the contact line of the droplet was de-pinned as the oscillation became more vigorous with increased energy input. The size of each lobe at the resonance frequency is somewhat larger than that at the neighboring frequency. A droplet in mode 2, one of the primary mode frequencies, exhibits vertical periodic movement as well as detachment and secondary ejection from the main droplet.