• Journal of Environmental Impact Assessment
• /
• v.6 no.2
• /
• pp.93-102
• /
• 1997

Acid rain below pH 5.6 is responsible for 40% of annual precipitation in Korea and it is more serious especially in major cites. Because of that, it is urgent to make measures to reduce the emission of $SO_2$, one of the major air pollutants causing acid rain. The national total emission of $SO_2$ in 1994 was estimated as 1.6 million tons. The $SO_2$ emission in 2020, is expected to increase up to 3.2 million tons, about 2 times that of 1994 under Business-As-Usual scenario. We could take various $SO_2$ reduction measures such as installing desulfurization facilities, the supply of low-sulfur oil and clean fuel(LNG), energy savings, upgrading of production process. However, it is necessary to check the economic feasibility and the attainability to reduction target with a dynamic optimization mode, "Global 2100 Model". The cost-benefit analyses for the measures using the revised "Global 2100 Model" clearly revealed that the desulfurization facilities should be introduced to reduce the $SO_2$ concentration to 0.01 ppm with fuel substitution. If the introduction of desulfurization facilities is delayed, We can not attain the goal of Ministry of Environment before the year of 2012, even in the case that almost all the fuels would be substituted with LNG.

• Plant Journal
• /
• v.17 no.2
• /
• pp.32-41
• /
• 2021

Recently, air environmental issues such as fine dust have rapidly emerged as national issues, and intensive environmental regulations are being applied to coal-fired power plants. This study introduces the case of improving the performance of desulfurization facilities for removing sulfur oxides and dust, which are the main air pollutant emitters of coal-fired power plants, and conducted four case studies to improve the performance of 1,000 MW power plants currently in operation and carried out construction. Liquid ratio was increased by remodeling the absorption tower of desulfurization facilities, and vaporization reaction was promoted by increasing the flow rate of oxidized air. In addition, the gas heater leakage rate was improved to improve the efficiency of final desulfurization facilities. It is expected that performance improvement work considering harmony with existing facilities will satisfy the regulations(25ppm of sulfur oxides, 5mg/Sm³) that will be applied from 2023, and can be referred to other thermal power plants for review and application.

• Resources Recycling
• /
• v.33 no.2
• /
• pp.3-15
• /
• 2024

Environmental awareness is rising worldwide. however, cement manufacturing facilities use recycled resources to improve raw material and fuel substitution rates, contributing to environmental issues such as waste disposal. The emission of sulfur oxides (SOx), an air pollutant, has been regulated by limestone as raw material in cement manufacturing. However, the impact of increasing use of recycled resources on future facility processes and environmental changes is unclear. Therefore, the cement manufacturing facilities require desulfurization-related technologies and research. In this study, we investigated the applicability of desulfurization technology to cement manufacturing facilities and demonstrated various approaches to applying this technology using byproducts generated in cement manufacturing.

• Plant Journal
• /
• v.12 no.1
• /
• pp.24-28
• /
• 2016

In desulfurization facilities of oil-fired power plant, gypsum scale is attached in the absorber inner surface as the operating time increases. For this reason, the maximum possible load of the power generation is set down, resulting in further generation stop. Cleaning of absorber for scale removal can be determined at the time of setting down of the maximum possible load. In this study, 6 weeks before the maximum possible load of the power generation was down set, at the same time and desulfurization facilities outlet $SO_2$ concentration value was more than 130ppm, absorber differential pressure exceeded $380mmH_2O$, it was confirmed to be the time that has elapsed 44 weeks after the previous absorber cleaning. Cleaning time of the absorber was predicted to be a time which has elapsed 50 weeks from the previous cleaning time.

• Journal of Korean Society for Atmospheric Environment
• /
• v.8 no.4
• /
• pp.262-268
• /
• 1992

The trend of international concerns on environmental conservation and domestic demand of ambient air quality improvement, specially on sulfur dioxide level has resulted in the establishment of mid-term strategy of environmental improvement and stepwise strengthening of emission regulations in this decade in Korea. Development of flue gas desulfurization(FGD) process is becoming an essential task to be accomplished especially for the power plants and large industrial facilities. This study is an initial stage researc focusing on the mass transfer principles in wet type FGD process and the effects of operating variables of a jet bubbling scrubber utilizing limestone slurry on sulfur dioxide removal efficiency. Experimental results showed this type of scrubbing system has some advantages in terms of mass transfer mechanism and removal efficiency. More rigorous research is needed for the reaction system and the comparison with existing FGD processess for the possible development of a process which is compatative in view of installation cost and treatment of by-products.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.857-864
• /
• 2011

Oxy-fuel combustion with many advantages such as high combustion efficiency, low flue gas flow rate and low NOx emission has emerged as a promising CCS technology for coal combustion facilities. In this study, the effects of the direct sulfation reaction on $SO_2$ removal efficiency were evaluated in a drop tube furnace under typical oxy-fuel combustion conditions represented by high concentrations of $CO_2$ and $SO_2$ formed by gas recirculation to control furnace combustion temperature. The effects of the operating parameters including the reaction temperature, $CO_2$ concentration, $SO_2$ concentration, Ca/S ratio and humidity on $SO_2$ removal efficiency were investigated experimentally. $SO_2$ removal efficiency increased with reaction temperature up to 1,200 due to promoted calcination of limestone reagent particles. And $SO_2$ removal efficiency increased with $SO_2$ concentrations and the humidity of the bulk gas. The increase of $SO_2$ removal efficiency with $CO_2$ concentrations showed that $SO_2$ removal by limestone was mainly done by the direct sulfation reaction under oxy-fuel combustion conditions. From the impact assessment of operation parameters, it was shown that these parameters have an effects on the desulfurization reaction by the order of the Ca/S ratio > residence time > $O_2$ concentration > reaction temperature > $SO_2$ concentration > $CO_2$ concentration > water vapor. The semi-empirical model equation for to evaluate the effect of the operating parameters on the performance of in-furnace desulfurization for oxy-fuel combustion was established.

• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.65-73
• /
• 2003

In Korea, not much interest has been paid yet to mercury among flue gas HAPs (Hazardous Air Pollutants), but mercury is expected to become a major problem in the near future. The present paper investigates the current state of mercury emission and control technologies. Interest of the U.S. and European countries in the area of air pollution has been recently directed to mercury emitted from power plants. There are largely two mercury removal technologies applied to power plants. One is removing mercury by oxidizing elemental mercury in WFGD (Wet Flue Gas Desulfurization), and the other is spraying an adsorbent such as activated carbon or other novel sorbents (low-cost sorbents). Developed country is requiring that all power plants be equipped with mercury control facilities by 2007. This paper aims at contributing to the establishment of future strategies in response to the problem.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.44-49
• /
• 2018

The use of fossil fuels is steadily increasing. The thermal power generation industry uses a lot of energy and emits a large amount of greenhouse gases. On the other hand, a desulfurization facility can be installed to remove sulfur content during boiler combustion process of the power plant. Dry desulfurized gypsum generated from dry desulfurization facilities is suitable as a $CO_2$ absorbing material due to the presence of CaO. In this study, the carbonation properties of dry desulfurized gypsum were investigated by carbonizing dry desulfurized gypsum via mixing with water and stirring. As a result of microstructural, XRD and thermal analyses of the carbonized dry desulfurized gypsum, the carbonation age was found to be suitable for 16 h. Dry desulfurized gypsum absorbs about 16% of $CO_2$ per unit weight.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.28 no.4
• /
• pp.15-22
• /
• 2020

The landfill gas produced in landfill is generally made up of methane(CH4) and carbon dioxide(CO2) of more than 90%, with the remainder made up of hydrogen sulfide(H2S). However, separate pre-treatment facilities are essential as hydrogen sulfide contained in landfill gas is combined with oxygen during the combustion process to generate sulfur oxides and acid rain combined with moisture in the atmosphere. Various desulfurization technologies have been used in Korea to desulfurize landfill gas. Although general desulfurization processes apply various physical and chemical methods, such as treatment of sediment generation according to the CaCO3 generation reaction and treatment through adsorbent, there is a problem of secondary wastes such as wastewater. As a way to solve this problem, a biological treatment process is used to generate and treat it with sludge-type sulfide (S°) using a biological treatment process.In this study, as a basic study of technology for utilizing the biological treatment by-products of hydrogen sulfide in landfill gas, an experiment was conducted to use the by-product as a mixture of concrete. According to the analysis of the mixture concrete strength of sulfur products, the mixture of sulfur by-products affects the strength of concrete and shows the highest strength value when mixing 10%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.83-86
• /
• 2006

In this study, the syngas producing facility that consists of pulverized coal feeding/gasification and hot gas clean-up system was tested for Indonesian subbituminous coal. And the DME conversion facilities have been developed and tested for converting syngas to DME by reactions with catalysts. So, the entrained-bed slagging type pi lot scale coal gasifier was operated normally in the temperature range of $1,400{\sim}1,450^{\circ}C,\;7{\sim}8kg/cm^2$ pressure. And Roto middle coal produced syngas that has a composition of $36{\sim}38%$ CO, $14{\sim}16%\;H_2,\;and\;5{\sim}8%\;CO_2$. Particulates in syngas were 99.8% removed by metal filters. $H_2S$ composition in syngas was also desulfurized by the Fe chelate system to yield less than 0.1 ppm level. When the clean syngas $70{\sim}100 Nm^3/h$ was provided to DME conversion rector, normally operated in the temperature range of $230{\sim}250^{\circ}C$ and $60kg/cm^2$ pressure, 4.5% DME was yielded.