• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.3
• /
• pp.81-86
• /
• 2010

Since CORDIC (COordinate Rotation DIgital Computer) is able to carry out the phase operation, such as vector to phase conversion or rotation of vectors, with adders and shifters, it is well suited for the design of the frequency synchronization unit in OFDM receivers. It is not easy, however, to fully utilize the CORDIC in the OFDM demodulator because of the non-linear characteristics of the direction sequence (DS), which is the representation of the phase in CORDIC. In this paper a new representation method is proposed to linearize the direction sequence approximately. The maximum phase error of the linearized binary direction sequence (LBDS) is also discussed. For the purpose of designing the hardware, the architectures for the binary DS (BDS) to LBDS converter and the LBDS to BDS inverse converter are illustrated. Adopting LBDS, the overall frequency synchronization hardware for OFDM receivers can be implemented fully utilizing CORDIC and general arithmetic operators, such as adders and multipliers, for the phase estimation, loop filtering of the frequency offset, derotation for the frequency offset correction. An example of the design of 22 bit LBDS for the T-DMB demodulator is also presented.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.1
• /
• pp.166-171
• /
• 2010

In this paper, the front-end of a digital receiver with a 25 kHz carrier frequency, 5 kHz symbol rate, and any excess-bandwidth is designed using two basic facts. The first is known as the uniform sampling theorem, which states that the sampled sequence might not suffer from aliasing even if its sampling rate is lower than the Nyquist sampling rate if the analog signal is a bandpass one. The other fact is that if the sampling rate is 4 times the center frequency of the sampled sequence, the front-end processing complexity can be dramatically reduced due to the half of the sampled sequence to be multiplied by zero in the demixing process. Furthermore, the designed front-end is simplified by introducing sub-filters and sub-sampling sequences. The designed front-end is composed of an A/D converter, which takes samples of a bandpass filtered signal at a 20 kHz rate; a serial-to-parallel converter, which converts a sampled bandpass sequence to 4 parallel sub-sample sequences; 4 sub-filter blocks, which act as a frequency shifter and lowpass filter for a complex sequence; 4 synchronized switches; and 2 adders. The designed front-end dramatically reduces the computational complexity by more than 50% for frequency shifting and lowpass filtering operations since a conventional front-end requires a frequency shifting and two lowpass filtering operations to get one lowpass complex sample, while the proposed front-end requires only four filtering operation to get four lowpass complex samples, which is equivalent to one filtering operation for one sample.

• Earthquakes and Structures
• /
• v.18 no.2
• /
• pp.147-162
• /
• 2020

This paper presents a novel precast energy dissipation shear wall (PEDSW) structure system that using mild steel dampers as dry connectors at the vertical joints to connect adjacent wall panels. Analytical studies are systematically conducted to investigate the seismic performance of the proposed PEDSW under sequence-type ground motions. During earthquake events, earthquake sequences have the potential to cause severe damage to structures and threaten life safety. To date, the damage probability of engineering structures under earthquake sequence has not been included in structural design codes. In this study, numerical simulations on single-story PEDSW are carried out to validate the feasibility and reliability of using mild steel dampers to connect the precast shear walls. The seismic responses of the PEDSW and cast-in-place shear wall (CIPSW) are comparatively studied based on nonlinear time-history analyses, and the effectiveness of the proposed high-rise PEDSW is demonstrated. Next, the foreshock-mainshock-aftershock type earthquake sequences are constructed, and the seismic response and fragility curves of the PEDSW under single mainshock and earthquake sequences are analyzed and compared. Finally, the fragility analysis of PEDSW structure under earthquake sequences is performed. The influences of scaling factor of the aftershocks (foreshocks) to the mainshocks on the fragility of the PEDSW structure under different damage states are investigated. The numerical results reveal that neglecting the effect of earthquake sequence can lead to underestimated seismic responses and fragilities, which may result in unsafe design schemes of PEDSW structures.

• The Journal of the Korea Contents Association
• /
• v.13 no.9
• /
• pp.410-417
• /
• 2013

Long-term behavior analysis considering construction sequence should be performed in the design and the actual construction of reinforced tall buildings. Most of the analytical studies on this subject, however, has not been applied directly to the structural design and the construction caused by the simple approach. As the axial force redistribution of shores and columns is time-dependent, the actual construction sequence with the placement of concrete, form removal, reshoring, shore removal, and the additional load application is very important. Object-oriented analysis program considering construction sequence, especially time-dependent deformation in early days, is developed. This system is composed of input module, database module, database store module, analysis module, and result generation module. Linkage interface between the central database and each of the related module is implemented by the visual c# concept. Graphic user interface and the relational database table are supported for user's convenience.

• Journal of information and communication convergence engineering
• /
• v.14 no.1
• /
• pp.26-34
• /
• 2016

The alignment of DNA sequences is one of the important processes in the field of bioinformatics. The Smith-Waterman algorithm (SWA) performs optimally for aligning sequences but is computationally expensive. Field programmable gate array (FPGA) performs the best on parameters such as cost, speed-up, and ease of re-configurability to implement SWA. The performance of FPGA-based SWA is dependent on efficient cell-basic implementation-unit design. In this paper, we present an optimized systolic cell design while avoiding oversimplification, very large-scale integration (VLSI)-level design, and direct mapping of iterative equations such as previous cell designs. The proposed design makes efficient use of hardware resources and provides portability as the proposed design is not based on gate-level details. Our cell design implementing a linear gap penalty resulted in a performance improvement of 32× over a GPP platform and surpassed the hardware utilization of another implementation by a factor of 4.23.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.1
• /
• pp.9-17
• /
• 2002

The study is insufficient on process planning of the elliptical deep drawing product. Thus, in this present study, the expert system for elliptical deep drawing products was constructed by using process sequence design. The expert system was developed to be based on the general concept of each entity. The system was developed in this work consists of sixth modules. The first one is a shape recognition module to recognize non-axisymmetric products and to generate Entity_list. The second one is three dimensional (3-D) modeling module to calculate the surface area for non-axisymmetric products. The third one is a blank design module to create suggested blanks of three shapes with the identical surface area. The fourth one is shape design module based on the production rules that play the most important role in an expert system for manufacturing. The production rules are generated and upgraded by inter- viewing field engineers, plastic theory and experiments. The fifth and sixth ones are a graphic module to visualize results of the expert system and a post module to rise user's convenience, respectively. According to constructed the expert system for process sequence design, it was possible to reduce the lead time.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.317-327
• /
• 2001

In this paper, a relation to calculate design moments for reinforced concrete(RC) bridges constructed by movable scaffolding system(MSS) is introduced. Through the time-dependent analysis of RC bridges considering the construction sequence, the structural responses related to the member forces and deflections are reviewed, and a governing equation for determination of the design moment, which includes the creep deformation, is derived on the basis of the displacement-force condition at every constructuion stage. By using the relation, the design moment and its variation over time can easily be obtained only with the elastic analysis results without additional time-dependent analysis. In addition, correlation studies with the results by rigorous numerical analyses are conducts to verify the applicability of the introduced relation, and a more reasonable guideline for the determination of design moments is proposed on the basis of the obtained moment envelop.

• Composites Research
• /
• v.30 no.1
• /
• pp.52-58
• /
• 2017

This paper presents the optimum design methodology for composite wing structure which automatically calculates the safety margin using optimization framework integrating failure modes. Particularly, its framework is possible to optimize sizing procedure to prevent failure mode which has the greatest effect on reducing the sizing time of composite structure. The main failure mode was set as the first ply failure, buckling failure mode, and bolted joint stress field, and the margin was calculated to minimize the weight. The design variable is a laminate sequence database and the responses are strain, buckling, bolted joint stress field. The objective function is the mass of the wing structure. The results of buckling analysis were compared using the finite element model to verify the robustness and reliability of Composite Optimizer.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1C
• /
• pp.46-54
• /
• 2006

The design method of synthetic aperture radar processor (SARP) in the critical design stage is to describe the processing algorithm, to estimate the fractional errors, and to set out the software (SW) and hardware (HW) mapping. The previous design methods for SARP are complex and depend on HW. Therefore, this paper proposes a critical design method that is of more general and independent of HW. This methodology can be applied for developing the space-based SARP using range-Doppler algorithm (RDA).

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.6
• /
• pp.15-20
• /
• 2016

In this paper, we consider selective mapping (SLM) based OFDM systems without side information, where SLM is one of the promising peak-to-average power ratio (PAPR) reduction techniques due to its simplicity and no distortion in the transmitted signal. First, we construct a new phase sequence where a part of phase sequence is replaced by an orthogonal sequence. Based on the proposed phase sequence, we propose a new scheme for detecting coherently the index of the phase sequence used in transmitter without side information. Computer simulation shows that the proposed detection scheme performs well in SLM-based OFDM systems, and specifically outperforms the existing ones when channel variation is relatively small between sub-carriers used in phase sequence detection.