• 대한토목학회논문집
• /
• 제31권1A호
• /
• pp.35-41
• /
• 2011

콘크리트구조설계기준에서는 일반적으로 처짐을 제어하기 위해 직접처짐제어법과 간접처짐제어법을 제시하고 있다. 이 때 처짐/깊이-비는 허용 처짐량을 초과하지 않도록 제한된다는 점에서 간접처짐제어법이 더 효과적이다. 실제 처짐량은 많은 요소에 의해 영향을 받기 때문에 실제 처짐량을 정확하게 산정하는 것은 어렵다. 이 연구에서는 철근콘크리트 부재의 사용한 계상태에서 처짐량을 직접 계산함으로써 한계 지간/깊이-비를 산정하였다. 이 때 처짐은 재료 모델로부터 산정된 휨곡률을 통해 산정하였다. 해석의 주요 변수는 인장증강효과 모델, 콘크리트 강도, 단면 크기 및 압축 철근의 유무이다. 해석 결과 2차식 형태의 인장증강효과 모델을 사용함으로써 해석의 일관성을 도모할 수 있는 것으로 나타났다. 또한 한계 지간/깊이-비는 단면 크기와 관계없이 재료 강도와 인장 및 압축 철근비에 따라 변화하는 것으로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권3호
• /
• pp.76-83
• /
• 2014

본 연구의 목적은 고강도 SFRC 보의 강섬유 보강효과를 평가하기 위한 것이다. 이를 위하여 13개의 실험체를 제작하여 성능실험을 실시하였다. 실험 변수는 전단경간비, 강섬유 혼입률, 전단보강근비이며 콘크리트 강도는 60 MPa이다. 기존 연구결과와 재료 및 부재 실험결과에 대한 분석에 의하면, 전단경간비 2.5와 강섬유 혼입률 1.0%인 경우가 강섬유 보강효과가 최대로 발휘되는 것으로 평가되었다. 강섬유 보강 및 전단경간비를 고려한 기존 전단내력식은 고강도 SFRC보의 내력을 과소평가하는 것으로 평가되었다. 향후 고강도 SFRC 보의 강도특성에 대한 보완 연구가 필요한 것으로 판단된다.

• Journal of Periodontal and Implant Science
• /
• 제31권2호
• /
• pp.477-488
• /
• 2001

The present study evaluated of regeneration effect of platelet rich plasma on the treatment of grade II furcation involvement, with coralline calcium phosphate bone in humans. 30 teeth with grade II furcation defect were selected and 15 teeth(control) were treated with coralline calcium phosphate bone, the others(test) were treated with coralline calcium phosphate bone and platelet rich plasma. Pocket depth, clinical attachment level, width of keratinized gingiva width were measured at baseline, postoperative 3, 6months. from cementoenamel junction to alveolar crest and fundus were measured at baseline, 6months(re-entry). Both groups were statistically analyzed by Wilcoxon signed Ranks Test & Mann-whitney Test using SPSS program(5% significance level). The results were as follows: 1. Pocket depth, clinical attachment level, keratinized gingva width, cementoenamel junction - alveolar crest, cementoenamel junction - fundus were not differ significantly in both groups at baseline 2. The change of pocket depth, clinical attachment level, keratinized gingva width, cementoenamel junction - alveolar crest, cementoenamel junction - fundus in both groups were decreased significantly at 3, 6months(p<0.05). 3. The change of pocket depth, clinical attachment level in test group decreased significantly than control at 3, 6months(p<0.05). 4. The change of keratinized gingiva width, cementoenamel junctional - alveolar crest, cementoenamel junction - fundus were not differ significantly in both groups at 3, 6months. 5. The pocket depth, clinical attachment level, keratinized gingiva width exhibited marked changes at 3 months in both groups. In conclusion, the results of this study suggest that platelet rich plasma have adjunctive clinical treatment effect to periodontal regeneration in grade II furcation defects.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.1080-1085
• /
• 1993

A nonlinear control algorithm for the depth control of underwater vehicles is presented. In order to consider the deadzone effect of the flow control valve, a nonlinear fuzzy logic controller (FLC) is synthesized and combined with a linear proportional-derivative-acceleration (PDA) controller, which is called, the PDA/FLC controller. And, to show the effectiveness of the PDA/FLC control system, it is compared with the linear PDA control system through computer simulation. It is found that the PDA/FLC control scheme is a suitable one to maintain the desirable depth of underwater vehicles with deadzone.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.20-23
• /
• 2002

In silicon wafer manufacturing process, the grinding process has been adopted to improve the quality of wafer such as flatness, roughness and so on. This paper describes the effect of grinding process on the surface quality of wafer. The experiments are carried out by high precision in fred grinder with air bearing spindle. The relationship between the inclination of chuck table and the flatness of wafer is investigated, and the effect of grinding conditions including wheel speed, table speed, and feed rate on damage depth and roughness of wafer is also investigated. The experimental results show that there is close relationship between the inclination of the chuck table and the flatness of wafer, and the grinding conditions within this paper little affect the flatness of wafer and relatively high affect the damage depth of wafer.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.155-161
• /
• 2005

Up to now, a lot of unmanned demining systems have been developed. However, some inferiority surely exist by reason of their large platform and explosive mechanism. To settle this inferiority, non-explosive demining system adaptable to a mobile robot already has been developed. Brief experiment indoors showed that developed demining system can remove landmines well. But, out of doors, several problems are detected. In this research, a study on the performance improvement of developed non-explosive demining system is mainly discussed. To overcome downhill effect, mechanical sensor composed of shaft and spring is used. It is confirmed that clearance depth control using the mechanical sensor is a good solution for the inclination of the system.

• Computers and Concrete
• /
• 제6권5호
• /
• pp.391-401
• /
• 2009

This paper presents a study of the strength and chloride penetration of blended Portland cement mortar containing ground palm oil fuel ash (POA) and ground river sand (GS). Ordinary Portland cement (OPC) was partially replaced with POA and GS. Compressive strength, rapid chloride penetration test (RCPT) and chloride penetration depth of mortars were determined. The GS only asserted the packing effect and its incorporation reduced the strength and the resistance to chloride penetration of mortar. The POA asserted both packing and pozzolanic effects. The use of the blend of equal portion of POA and GS also produced high strength mortars, save cost and excellent resistance to chloride penetration owing to the synergic effect of the blend of POA and GS. For chloride depth, the mathematical model correlates well with the experimental results. The computer graphics of chloride depth of the ternary blended mortars are also constructed and can be used to aid the understanding and the proportioning of the blended system.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.886-895
• /
• 1993

Experimental were conducted to obtain information on the effect of airflow rates and bed depths on the resistance of coffee cherries and coffee beans available locally (Coffea Liberica). The airflow used were in the range of 0.06 to 0.6 cu. m/s-sq.m. The moisture content of the coffee cherries ranged from 10 % to 50% (wet basis) and that of coffee beans ranged from 12% to 30% )wet basis). Two methods of filling were used i.e. loose fill and packed fill. Pressure drops across the material bed in a vertical column were measured at several depths using inclined manometer. The pressure drop increased directly with air flow rate as well as bed depths. The effects of air flowrates and moisture contents on the resistance in terms of pressure drip per unit bed depth were analysed. The pressure drop per unit depth across the material bed varied slightly due to different depth. The resistance to airflow decreased with the increase in moisture content for loose fill. However, the effect of moisture content is not apparent for packed fill.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.104-116
• /
• 1998

This paper provides a review of the performance for SM45C using the CNC lathe. Under the constant cutting area, the tool wear for large feed rate is more than the small feed rate, and the progress goes more rapidly as the cutting speed is increased. This is caused by the friction between the workpiece and the bite. The average cutting force increases as the feedrate increases, and decreases as the cutting speed increases. This is because the effective rake/shear angle becomes smaller as the feedrate becomes larger. The higher is the cutting speed and the aspect ratio (the ratio for depth of cut to feedrate), the lower is the cutting force and the surface roughness. Also, for the optimal selection of the cutting conditions, many experimental graphical data were obtained. That is, the cutting force, the tool life, and the surface roughness were measured and investigated as the depth of cut and the feedrate changed. And the size effect was examined as the depth of the cut varied.

• 한국주조공학회지
• /
• 제9권3호
• /
• pp.221-227
• /
• 1989

The effect of sulfur content and inoculant on solidification microstructure and mechanical properties of gray cast iron have been investigated. The main results obtained are as follows, 1. In the FeSi3Ca1Ba inoculated irons, with the variation of sulfur content, low sulfur levels (${\sim}0.03%$) yield low chill depth, high tensile strength, good wear resistance and type A graphite with a pearlite matrix. High sulfur levels( >0.08%) provide high chill depth, low mechanical proper ties and type D graphite with small amount ferrite. 2. In case of inoculant variation with normal FeSi, FeSi3Ca1Ba, 30CaSi and uninoculation at 0.03%S level, lower chill depth and higher tensile strength was obtained in the order ; 30CaSi, FeSi3Ca1Ba normal FeSi, uninoculation.