• Wind and Structures
• /
• v.32 no.5
• /
• pp.453-469
• /
• 2021

Snow accumulation on the road frequently induces a big traffic problem in the cold snowy region. Accurate prediction on snow distribution is fundamental for solving drifting snow disasters on roads. The present study adopts the transient method to simulate the wind-induced snow distribution on embankment based on the mixture multiphase model and dynamic mesh technique. The simulation and field measurement are compared to confirm the applicability of the simulation. Furthermore, the process of snow accumulation is revealed. The effects of friction velocity and snow concentration on snow accumulation are analyzed to clarify its mechanism. The results show that the simulation agrees well with the field measurement in trends. Moreover, the snow accumulation on the embankment can be approximately divided into three stages with time, the snow firstly deposited on the windward side, then, accumulation occurs on the leeward side which induced by the wake vortex, finally, the snow distribution reaches an equilibrium state with the slope of approximately 7°. The friction velocity and duration have a significant influence on the snow accumulation, and the vortex scale directly affected the snow deposition range on the embankment leeward side.

• Fisheries and Aquatic Sciences
• /
• v.13 no.2
• /
• pp.167-181
• /
• 2010

To predict changes in the marine environment of the Beolgyo Stream Estuary in Jeonnam Province, South Korea, where cohesive tidal flats cover a broad area and a large bridge is under construction, this study conducted numerical simulations involving tidal flow and cohesive sediment transport. A wetting and drying (WAD) technique for tidal flats from the Princeton Ocean Model (POM) was applied to a large-scale-grid hydrodynamic module capable of evaluating the flow resistance of structures. Derivation of the eddy viscosity coefficient for wakes created by structures was accomplished through the explicit use of shear velocity and Chezy's average velocity. Furthermore, various field observations, including of tide, tidal flow, suspended sediment concentrations, bottom sediments, and water depth, were performed to verify the model and obtain input data for it. In particular, geologic parameters related to the evaluation of settling velocity and critical shear stresses for erosion and deposition were observed, and numerical tests for the representation of suspended sediment concentrations were performed to determine proper values for the empirical coefficients in the sediment transport module. According to the simulation results, the velocity variation was particularly prominent around the piers in the tidal channel. Erosion occurred mainly along the tidal channels near the piers, where bridge structures reduced the flow cross section, creating strong flow. In contrast, in the rear area of the structure, where the flow was relatively weak due to the formation of eddies, deposition and moderated erosion were predicted. In estuaries and coastal waters, changes in the flow environment caused by artificial structures can produce changes in the sedimentary environment, which in turn can affect the local marine ecosystem. The numerical model proposed in this study will enable systematic prediction of changes to flow and sedimentary environments caused by the construction of artificial structures.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.1
• /
• pp.51-66
• /
• 2021

This study shows that coastal sand dunes are negatively affected by coastal forests. In South Korea, planting pine trees on the dunes has been carried out to stabilize the dune landscapes and protect residential areas from coastal disasters since the 20th century. However, this strategy could reduce the resilience of dunes. In this study, we selected three monitoring sites with automated weather stations to compare the geomorphological and environmental characteristics between tree-covered and grass-covered dunes at Sohwang-ri, Boryeong-si, Chungnam Province for three years. In addition, we monitored the rates of erosion and deposition using eight pins along the dune crests. We found that the forest affected both wind velocity and direction, resulting in decreased blown sand supply to the dunes in front of the forest. The velocity of the strong winds faster than 5 m/s diminished to 10%-30% of the control sites, and the direction of northwesterly wind were skewed to the north by about 6°. Sand deposition occurred at about 15-20 m away from the pine forest and the amount was only 1/10 of the deposition within the grass-covered dunes. This study suggests that planting trees in coastal dunes is an undesirable strategy with negative impacts on the landscape management.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2881-2892
• /
• 2024

Annular flow refers to a special type of two-phase flow pattern in which liquid flows as a thin film at the periphery of a pipe, tube, or conduit, and gas with relatively high velocity flows at the center of the flow section. This gas also includes dispersed liquid droplets. The liquid film flow rate continuously changes inside the tube due to two processes-entrainment and deposition. To determine the liquid holdup, pressure drop, the onset of dryout, and heat transfer characteristics in annular flow, it is important to have proper knowledge of flow characteristics. Especially a better understanding of entrainment fraction is important for the heat transfer and safe operation of two-phase flow systems operating in an annular two-phase flow regime. Therefore, the objective of this work is to develop a computational model for the simulation of the annular two-phase flow regime and assess the various existing models for the entrainment rate. In this work, Computational Fluid Dynamics (CFD) in ANSYS FLUENT has been applied to determine annular flow characteristics such as liquid film thickness, film velocity, entrainment rate, deposition rate, and entrainment fraction for various gas-liquid flow conditions in a vertical upward tube. The gas core with droplets was simulated using the Discrete Phase Model (DPM) which is based on the Eulerian-Lagrangian approach. The Eulerian Wall Film (EWF) model was utilized to simulate liquid film on the tube wall. Three different models of Entrainment rate were implemented and assessed through user-defined functions (UDF) in ANSYS. Finally, entrainment for fully developed flow was determined and compared with the experimental data available in the literature. From the simulations, it was obtained that the Bertodano correlation performed best in predicting entrainment fraction and the results were within the ±30 % limit when compared to experimental data.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.10 no.S_2
• /
• pp.55-63
• /
• 2001

This work employs two models to quantify the size-segregated dry deposition fluxes of particle-bound N $O_3$$^{[-10]}$ , N $H_4$$^{+}$, and S $O_4$$^{2-}$ along the coastal area of Jeju Island based on the chemical composition data of aerosol collected during the springtime of 1995. The two approaches produced fairly comparable results, despite the feature differences between the two models. The modelling results obtained indicated that the mean dry deposition velocity was around 0.4 cm $s^{-1}$ for N $O_3$$^{[-10]}$ , 0.2 cm $s^{-1}$ for N $H_4$$^{+}$, and 0.3 cm $s^{-1}$ for S $O_4$$^{2-}$, and the dry deposition flux varied between 371~1368 $\mu\textrm{g}$ $m^{-2}$ da $y^{-1}$ for nitrate, 28~625 $\mu\textrm{g}$ $m^{-2}$ da $y^{-1}$ for ammonium, and 957~6088 $\mu\textrm{g}$ $m^{-2}$ da $y^{-1}$ for sulfate. Although difficulties in collecting giant and/or fine particles limited the understanding of the mass size distribution of particles and thus the ability to refine estimates of the dry deposition flux for the particulate matter, both models were still able to offer sufficient realism to explain the features of the available data collected from the coastal area of Jeju Island.and.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.57-65
• /
• 2014

For economic and technical reasons, it is difficult to obtain high quality undisturbed cohesionless samples, hence most researchers rely on preparing remolded and reconstituted representative samples of sandy soils. In this study, moist tamping, air pluviation, and dry deposition methods were applied to make remolded samples at similar relative densities. A series of isotropically consolidated drained tests were conducted with accompanied by measured elastic wave velocities in order to evaluate a difference between sample preparation methods and relative densities. For the elastic wave velocity measurements, piezoelectric elements were installed on the top and bottom cap of the triaxial device. The results showed that soil behavior relies on sample preparation methods, and that the trend of shear wave velocity was the same with volumetric strain behavior.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.8
• /
• pp.830-835
• /
• 1998

The characteristics of the ablation plume generated by 532 nm Nd: YAG laser irradiation of a Pb(Zr0.52Ti0.48)O3 (PZT) target have been investigated using a pulsed-field time-of-flight mass spectrometer (TOFMS). The relative abundance of O+, Ti+, Zr+, Pb+, TiO+, and ZrO+ ions has been measured and discussed. TiO+ and ZrO+ ions were also found to be particularly stable within the laser ablation plasma with respect to PbO+ species. The behavior of the temporal distributions of each ionic species was studied as a function of the delay time between the laser shot and the ion extraction pulse. The most probable velocity of each ablated ion is estimated to be Vmp=1.1-1.6x 105 cm/s at a laser fluence of 1.2 J/cm2, which is typically employed for the thin film deposition of PZT. The TOF distribution of Ti+ and Zr+ ions shows a trimodal distribution with one fast and two slow velocity components. The fast velocity component (6.8x 10' cm/s) appears to consist of directly ablated species via nonthermal process. The second component, originated from the thermal evaporation process, has a characteristic velocity of 1.4-1.6 x 105 cm/s. The slowest component (1.2 x 105 cm/s) is composed of a dissociation product formed from the corresponding oxide ion.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.18-21
• /
• 2018

We report on the simple preparation method of large-scale structured catalysts by temperature-regulated chemical vapor deposition with a high cell-density ceramic honeycomb monolith. And the feasibility for dry reforming of methane catalysts was evaluated. The NiO/Cordierite (CDR) catalyst was prepared by controlling coating conditions at each temperature step, leading to a conformal deposition of NiO inside the cordierite honeycomb monolith with the cell density of 600 cpsi. The catalytic conversion of $CH_4$ and $CO_2$ for dry reforming of methane were about 83% and 90% with gas hourly space velocity of $10,000h^{-1}$ at $800^{\circ}C$, respectively. As a result, it exhibited that the temperature-regulated chemical vapor deposition method can be expedient for the preparation of large-scale structured catalysts.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.3
• /
• pp.101-104
• /
• 2022

Mist-CVD is known to have advantages of low cost and high productivity compared to ALD and PECVD methods. It is capable of reacting to the substrate by misting an aqueous solution using ultrasonic waves under vacuum-free conditions of atmospheric pressure. In particular, Ga₂O₃ is regarded as advanced power semiconductor material because of its high quality of transmittance, and excellent electrical conductivity through N-type doping. In this study, Computational Fluid Dynamics were used to predict the uniformity of the thin film on a large-area substrate. And also the deposition pattern and uniformity were analyzed using the flow velocity and particle tracking method. The uniformity was confirmed by quantifying the deposition cross section with an FIB-SEM, and the consistency of the uniformity prediction was secured through the analysis of the CFD distribution. With the analysis and experimental results, the match rate of deposition area was 80.14% and the match rate of deposition thickness was 55.32%. As the experimental and analysis results were consistent, it was confirmed that it is possible to predict the deposition thickness uniformity of Mist-CVD.

• Journal of Korea Water Resources Association
• /
• v.40 no.9
• /
• pp.723-734
• /
• 2007

This study was to investigate the settling velocity which is an important factor for the prediction of cohesive deposition under the various densities of particle and dissolved ion addition$(Na^+,\;Cl^-,\;OH^-,\;H^+)$ in rivers, ports, reservoirs and lakes. Settling velocity of suspended fine particles in still water was measured with a pressure sensor (maximum 10 mbar). At the initial concentration of 20g/l of alumina and quartz the average settling velocities were high due to the aggregation behaviour of particles. At this point it was 0.185 mm/s (alumina) and 0.022 mm/s (quartz). Above this initial concentration it was on the decrease owing to the hindered settling. The higher the salinity is, the faster the settling velocity of alumina and quartz is. Furthermore, in an acid condition the average settling velocity of alumina was on the decrease. In an alkaline water, which causes strong flocculation, the average settling velocity of alumina it was observed on the increase. However, in an alkaline medium the low average settling velocity of quartz powder was measured.