• 한국정보통신학회논문지
• /
• 제20권8호
• /
• pp.1546-1552
• /
• 2016

일반적으로 치과용 주조기는 불때를 이용하여 합금을 용해하기 때문에 합금의 적절한 용융온도 및 주조시간을 조절하기 어렵고 이로 인해 가스공이나 핀홀과 같은 주조결함을 발생시키며 과열로 인한 보철물의 결함을 보이고 있다. 또한 합금이 용융된 후 주조 시 대부분 투시창이나 비접촉식 온도센서를 부착하여 적절한 주조온도가 되면 작업자가 원심력을 발생하는 버튼을 눌러 도가니에 용융된 합금을 주조링에 주입한다. 이러한 결과로 대부분 주조온도가 너무 높거나 낮아서 주조결함을 많이 발생하고 있으며 균일한 주조체를 얻지 못하고 있는 실정이다. 본 논문에서는 외부의 비접촉식 온도 센서를 이용한 온도계측이 아닌 실제 합금의 사용 온도를 계측할 수 있는 단일 온도센서를 이용한 치과용 고주파 주조기를 개발하였다.

• 대한치과기공학회지
• /
• 제23권1호
• /
• pp.9-19
• /
• 2001

Microstructure and phase transformation of Ti-Ni-Cu alloy powders produced by using attrition milling method were studied. Mixed powders of Ti-(50-X)Ni-XCu ($X=0{\sim}20$ at%) in composition range were mechanically alloyed for maximum 20 hours by using SUS 1/4" ball in argon atmosphere. Ball to powder ratio was 50: 1 and impeller speed was 350rpm. Mechanically alloyed with attrition millimg method. powder was heat treated at the temperature up to $850^{\circ}C$ for 1 hour in the $10^{-6}$ torr vacuum. Ti-Ni-Cu alloy powders have been fabricated by attrition milling method. and then phase transformation behaviours and microstructual properties of the alloy powders were investigated to assist in improving the the high damping capacity of Ti-Ni-Cu shape memory alloy powders. The results obtained are as follows: 1. After heat treating of fully mechanically alloyed powder at $850^{\circ}C$ for 1hour. most of the B2 and B 19' phases was formed and $TiNi_3$ were coexisted. 2. The B 19' martensite were formed in Ti-Ni-Cu alloy powders whose Cu-content is less than 5a/o. where as the B19 martensite in those whose Cu-content is more than 10at%. 3. The powders of as-milled Ti-Ni-Cu alloys whose Cu-contents is less than 5at% are amorphous. whereas those of as-milled Ti-Ni-Cu alloys whose Cu-content is more than 10at% are crystalline. This means that Cu addition tends to suppress amorphization of Ti-Ni alloy powders.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.105-112
• /
• 2013

Purpose: This study was to analyze the castability, surface oxide characteristic of Co-Cr alloy for porcelain fused to metal crown and the bonding strength of porcelain fused to metal crown. Co-Cr and Ni-Cr alloy for porcelain fused to metal crown was used for tests of the castability and surface oxide state and shear bonding strength by various porcelain. The aim of this study was to suggest the differences of result according to Co-Cr and Ni-Cr alloy. Methods: The kinds of alloy as test specimen was Co-Cr and Ni-Cr alloy. The castability index on the alloy specimens. The surfaces of two alloys were analyzed by SEM and EDX in order to observe oxide characteristic. And the shear test was performed by MTS. Results: The castability index of Co-Cr alloy was 96.8% and Ni-Cr alloy was 94.4%. The strongest bonding strength of Co-Cr alloy was shown 67.37 MPa. Conclusion: The shear bonding strength between Co-Cr alloy and EX3 porcelain was the strongest comparing with others. And all of each alloy was indicated as same level about the castability.

• 대한치과의사협회지
• /
• 제12권9호
• /
• pp.667-677
• /
• 1974

A testing machine was devised and constructed for the purpose of measuring the retentive forces of maxillary complete denture bases in subjects. Forth complete denture bases were made for ten subjects with three different denture base materials, following the usual denture construction technique. Retentive forces of the forty dentures were determined at seven locations. The tests on each base were repeated three times at intervals of 5 minutes. Differences in retention values were evaluated statistically. 1) Differences in retention values were found by the differences of the denture base materials, but acrylic resin was similar to chromium cobalt alloy. 2) The chromium cobalt alloy and acrylic resin bases from master models revealed the best retention values, the gold alloy base from master model was the poor second and the acrylic resin base from snap model was the third. 3) The retention values for hook-1 revealed higher than that for hook-2 and the retention values for hook-3 revealed the lowest value.

• 대한치과기공학회지
• /
• 제24권1호
• /
• pp.95-104
• /
• 2002

For biomedical applications, Ti-X%Zr-Y%Nb-0.2%Pd(X:10$\sim$20, Y:2$\sim$8) alloys not containing harmful Al and V were newly designed, and the effect of alloy composition and heat treatment on the microstructure and mechanical properties was investigated. From the results, it was shown that the mechanical properties were enhanced with the addition of Zr or Nb. The effect of heat treating on room temperature strength was investigated by aging treatment after solution treatment. The mechanical properties of Ti-20%Zr-4%Nb-0.2%Pd alloy aged at 400$^{\circ}C$ for 10hrs was found to be superior to those of the pure Ti and Ti-6%Al-4%V ELI alloy.

• 대한치과기공학회지
• /
• 제23권1호
• /
• pp.21-30
• /
• 2001

For biomedical applications. Ti-X%Zr-Y%Pd(X: $10{\sim}20$, Y:0.2 or 0.4) based alloys not containing harmful Al and V were newly designed, and polarization curves for their alloys were measured at $37^{\circ}C$ in 5% HCl solution in order to understand effects of Zr on the corrosion. From the results of anodic polarization behavior, it was found that the corrosion resistance increased with increasing Zr content. The results show their potential to develope Ti-based alloys for biomedical materials. The Ti-20%Zr-0.2%Pd alloy shows excellent corrosion resistance and was superior to those of the Ti. Ti-6%Al-4%V ELI alloy, Co-30%Cr-6%Mo alloy and STS 316L stainless steel.

• 대한치과기공학회지
• /
• 제19권1호
• /
• pp.21-35
• /
• 1997

Au 함량이 20% 미만인 Au-Ag-Pd합금의 기초합금인 Ag-Pd-Cu 3원계 합금의 시효경화 특성을 규명할 목적으로 20wt% Pd 및 20wt% Cu의 용질농도구성비가 1이 되는 3원 합금과 여기에 2wt% Au의 첨가합금에 미치는 석출상의 영향을 분석, 조사하여 아래와 같은 결론을 얻었다. Ag-20wt% Pd-20wt% Cu 3원 함금은 ${\alpha}$의 단일상에서 Ag-rich의 ${\alpha}2$상 및 PdCu규칙상에 의하여 경화반응이 진행되며 연속승온과정에서 $100{\sim}300^{\circ}C$의 경도증가와 $300{\sim}500^{\circ}C$의 경도감소의 2단계 경화특성이 얻어졌다. 연속승온시효과정은 Au첨가에 관계없이 2단계의 석출반응이 저온영역에서는 stage I, stage II로 나타나고 stage I은 고온에서의 소입에 의해 도입된 과잉공공의 이동 및 소멸에 의한 반응이고 stage II는 평형농도의 공공확산에 의한 반응에 대응하였다. 또한 본 합금의 시효석출과정은 ${\alpha}\to{\alpha}+{\alpha}2+PdCu\to{\alpha}_1+{\alpha}_2+PdCu$이고 최대 경화는 ${\alpha}_1,\;{\alpha}_2$, PdCu의 3상공존구역에서 나타났다. 이들 석출반응은 입계반응이고 반응의 진행과 함께 경도값은 상승하며 경화능에 직접적으로 기여하였다. 또한 석출상은 미세한 lamella조직의 nodule을 나타내고 이들 ${\alpha}_1,\;{\alpha}_2$ 및 PdCu상과의 미세한 혼합상의 형성이 시효경화능에 기여하는 주된 원인이 되었다. 과시효는 lamella의 조대화와 PdCu상의 ${\alpha}_2$상으로의 용해에 따른 정량적 감소에 대응하였다. 본 합금의 시효열처리 온도는 $450^{\circ}C$가 적절하며 $1{\sim}120min$ 시효시간에 걸쳐서 소정의 경화특성을 얻을 수 있었다.

• 대한치과기공학회지
• /
• 제28권1호
• /
• pp.61-66
• /
• 2006

Titanium alloys have been used for dental materials due to it's very good biocompatibility. Ti-6Al-4V alloy instead of pure titanium is being widely used as biomaterials has some characteristics such as high fatigue strength, tensile strength and corrosion resistance. But it has been reported recently that the vanadium element expresses cytotoxicity and carcinogenicity and the aluminium element is related with dementia of Alzheimer type and neurotoxicity. The Ti-Nb alloys has designed and examined corrosion resistance. Ti-3wt.%Nb($\alpha$type), Ti-20wt.%Nb(${\alpha}+{\beta}$type) and Ti-40wt.%Nb($\beta$type) alloys were melted by vacuum arc furnace. The corrosion resistance of Ti alloys was evaluated by potentiodynamic polarization test in the solution of 0.9% NaCl and 5% HCl. The results can be summarized as follows: 1) For the corrosion test in the solution of 0.9% NaCl and 5% HCl, the corrosion behaviour of Ti-Nb alloys was similar to ASTM grade 2 CP Ti. 2) The corrosion resistance of Ti-20Nb alloy was better than that of CP-Ti, Ti-3Nb, Ti-40Nb alloy in 0.9% NaCl and 5% HCl, solutions.

• 대한치과기공학회지
• /
• 제14권1호
• /
• pp.119-132
• /
• 1992

This paper aims to investigate the effect of B and Si upon the mechanical properties, microstructure and corrosion resistance of Co-Cr base alloy. Ten groups of alloy ingot ingot with various contents of B and Si were remelted by high frequency electrical induction furnace and cast into tensile specimen of ADA Specification No. 14 Tensile and hardness test were carried out by Amsler and Rockwell hardness tester(R-30N), respectively. The microstructures of specimen were observed by SEM. The results obtained are summarized as follows : 1. As B content is increased, tensile strength, yield strength and Rockwell hardness number(R-30N) are also increased significantly, while the elongation is decreased significantly. 2. As Si contect os increased, no significant chang in tensile strength is noticed, yield strength is slightly decreased, but Rockwell hardness number(R-30N) is moderately in creased, Elongation marks maxium value with 1% Si content while with more than 1% Si it is decreased. 3. As B content is increased corrosion resistance is decreased and is at best with 1.5% B content. Corrosion resistance is increased with the increase of Si content and the alloys with Si over 3.0% showed corrosion resistance. 4. As B content increased, precipitates are increased in number at grain boundaries. The grain size tends to become coarse with the increase of Si content. 5. Co rich-Cr alloy is present through matrix whereas at the grain boundaries Cr base precipitates are primarily formed.

• Corrosion Science and Technology
• /
• 제4권1호
• /
• pp.19-22
• /
• 2005

Two Au-Ag-Cu-Pd dental casting alloys (Au:12% and 20%) used. The test solutions used 0.9 % NaCl solution (isotonic sodium chloride solution), 0.9 % NaCl solution containing 1 % lactic acid, and 0.9 % NaCl solution containing 1 % lactic acid and 0.1 mol $dm^{-3}$ $Na_2S$. The surface of two samples in three sample solutions was not natural discoloration during one year. The alloy containing 12 % gold was easily alloyed and the composition was uniform comparing with the alloy containing 20 % gold. The rest potentials have not a little effect after three months. The kinds of metals could not definitely from the oxidation and reduction waves of metal on the cyclic voltammograms. The dissolutions of gold and palladium were 12 % Au sample in the 0.9 % NaCl solution containing 1 % lactic acid and 0.1 mol $dm^{-3}$ $Na_{2}S$. The pH of solution had an affect on dissolution of copper, and sulfur ion had an affect on dissolution of silver. The copper dissolved amount from 20 % gold sample was about 26 times comparing with that of 12 % gold sample in the 0.9 % solution containing 1 % lactic acid. Corrosion products were silver chloride and copper chloride in NaCl solution, and silver sulfide and copper sulfide in NaCl solution containing $Na_{2}S$.