• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.171-173
• /
• 2002

This paper describes the open frame type high power density switching converter. It is based on active clamp forward converter with synchronous rectifier, and packaged by using the open frame and multi-layer printed circuit board (PCB) techniques to achieve the high power density. Furthermore, windings of transformer and inductor are also realized by multi-layer PCB so that it achieves the higher power density. Through the experiment on the proto-type converter of 50[W], it is confirmed that power density of $50[W/in^3]$ and maximum efficiency of over 91 [%] are obtained.

• 한국통신학회논문지
• /
• 제31권9C호
• /
• pp.825-830
• /
• 2006

Capacity-approaching codes using iterative decoding have been the main subject of research activities during past decade. Especially, LDPC codes show the best asymptotic performance and density evolution has been used as a powerful technique to analyze and design good LDPC codes. In this paper, we apply density evolution with a Gaussian approximation to the concatenated zigzag (CZZ) codes by considering both flooding and two-way schedulings. Based on this density evolution analysis, the threshold values are computed for various CZZ codes and the optimal structure of CZZ codes for various code rates are obtained. Also, simulation results are provided to conform the analytical results.

• Current Research on Agriculture and Life Sciences
• /
• 제33권1호
• /
• pp.7-14
• /
• 2015

This study identifies the complementarity or substitutability among apple production technology bundles. To identify the production technology bundle relationships, this paper focuses on the 8 most commonly used technology groups, including a high density plant, normal density plant, M9, M26, more than 70% adoption ratio of a medium-maturing variety, the adoption of a new variety, artificial pollination, and low-temperature storage. The results show that M9 has a complementary relationship with a high density plant, yet a substitute relationship with a normal density plant. Meanwhile, M26 has a complementary relationship with both a high and normal density plant. No substitute relationship is found between M9 and M26, yet a complementary relationship is identified between the adoption of artificial pollination and low-temperature storage and M9 or M26.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.738-739
• /
• 2006

This paper will describe a powder and processing method that facilitates single press-single sintered densities approaching $7.5g/cm^3$. At this sintered density, mechanical properties of the powder metal (P/M) component are significantly improved over current P/M technologies and begin to approach the performance of wrought steels. High performance gears have the added requirement of rolling contact fatigue durability that is dependent upon localized density and thermal processing. Combining high density processing of engineered P/M materials with selective surface densification enables powder metal components to achieve rolling contact fatigue durability and mechanical property performance that satisfy the performance requirements of many high strength automotive transmission gears. Data will be presented that document P/M part performance in comparison to conventional wrought steel grades.

• 한국인쇄학회지
• /
• 제10권1호
• /
• pp.15-22
• /
• 1992

This paper proposed correction tone density eq. and dot area eq. for perdict tone reproduction when dot gain is constant, and these are based on Yule & Nielson`s tone density equation. The experimental results show that proposed coreaction tone density eq. and dot area eq. are useful and valid for perdict tone reproduction of a half-tone image.

• 대한전자공학회논문지TC
• /
• 제47권11호
• /
• pp.36-42
• /
• 2010

이 논문은 유클리드 기하학과 Circulant Permutation Matrices에서 병렬 구성을 기반으로 하는 Quasi-cyclic Low-density parity-check (QC-LDPC) 코드의 생성을 위한 하이브리드한 접근방식을 나타낸다. 이 방법으로 생성된 코드는 넓은 둘레(Large Girth)와 저밀도(Low Density)를 가진 규칙적인 코드로 나타내어진다. 시뮬레이션 결과는 이 코드들이 반복 복호(Iterative Decoding)를 통해 좋은 성능을 갖는것과 부호화되지 않은 시스템에서 좋은 코딩 이득을 달성하는 것을 보인다.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 춘계학술발표논문집
• /
• pp.70-79
• /
• 2003

Paper coating can give smoothness surface and good printability to uncoated paper. Macro roughness of base paper would be decreasing its groove and grit in view of side. Nevertheless its improving effect for paper, some kind of problem is showing in the fine coated paper. Especially, back trap mottle is one of serious problems in printing with fine coated paper. Printers can not adjust conditions to overcome the problem. Also large amounts of paper can be rejected. There are many factors that influence back trap mottle. However it is not clear what the important parameters are in back trap mottle. Back trap mottle has some relationship with ink setting but good guidelines are not clear. Back trap mottle has been linked to non-uniform ink setting. We do not know how much variation in setting we can tolerate. Other mottle issues such as micro-picking and ink refusal are still common. This paper was prepared to identify correlation with ink setting and delta ink density obtained from experiment and then tried to find out some relationships with ink setting and back trap mottle. Basically fine calcium carbonate and ciay was used for main components and coarse calcium carbonate was mixed in two fine pigments to change its porosity and ink acceptance. Micro ink tack force at KRK printing tester was adapted to measure ink setting rate. KRK units were used for back trap mottle simulation and two printed samples were prepared to check delta ink density. Clay base coating has more fast ink setting time than calcium carbonate's though smoothness of clay was better than calcium carbonate. It could be explained by that clay has finer pore in its coating than calcium carbonate. DID(delta ink density) has shown a good correlation with ink setting time from micro ink tack. The total pore volume of coating layer did not match with ink setting and DID. From the results we might conclude coating that has fine pore size around 0.05 ${\mu}m$ can be exposed to high possibility of back trap mottle.

• Nuclear Engineering and Technology
• /
• 제55권12호
• /
• pp.4685-4694
• /
• 2023

The ability to calculate the material density sensitivity coefficients of power with respect to the material density has broad application prospects for accelerating Monte Carlo-Thermal Hydraulics iterations. The second-order material density sensitivity coefficients for the general Monte Carlo score have been derived based on the differential operator sampling method in this paper, and the calculation of the sensitivity coefficients of cell power scores with respect to the material density has been realized in continuous-energy Monte Carlo code RMC. Based on the power-density sensitivity coefficients, the sensitivity coefficients of power scores to some other physical quantities, such as power-boron concentration coefficients and power-temperature coefficients considering only the thermal expansion, were subsequently calculated. The effectiveness of the proposed method is demonstrated in the power-density coefficients problems of the pressurized water reactor (PWR) moderator and the heat pipe reactor (HPR) reflectors. The calculations were carried out using RMC and the ENDF/B-VII.1 neutron nuclear data. It is shown that the calculated sensitivity coefficients can be used to predict the power scores accurately over a wide range of boron concentration of the PWR moderator and a wide range of temperature of HPR reflectors.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.17-23
• /
• 1997

In the two-dimensional Finite Element Method for forming simulation, mesh generation and remeshing process are very significant. In this paper, using the modified splitting mesh generation algorithm, we can overcome the limitation of existing techniques and acquire mesh, which has optimal mesh density. A modified splitting algorithm for automatically generating quadrilateral mesh within a complex domain is described. Unnecessary meshing process for density representation is removed. Especially, during the mesh generation with high gradient density like as shear band representation, the modified mesh density scheme, which will generate quadrilateral mesh with the minimized error, which takes effect on FEM solver, is introduced.

• Korean Journal of Mathematics
• /
• 제27권1호
• /
• pp.193-219
• /
• 2019

The Navier-Stokes equations with variable density are challenging problems in numerical analysis community. We recently built the 2nd order stabilized Gauge-Uzawa method [SGUM] to solve the Navier-Stokes equations with constant density and have estimated theoretically optimal accuracy. Also we proved that SGUM is unconditionally stable. In this paper, we apply SGUM to the Navier-Stokes equations with nonconstant variable density and find out the stability condition of the algorithms. Because the condition is rather strong to apply to real problems, we consider Allen-Cahn scheme to construct unconditionally stable scheme.