• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.410-414
• /
• 2001

The microstructure, V-I characteristics, and stability of ZnO-Pr$_{6}$O$_{11}$-CoO-Cr$_2$O$_3$-Y$_2$O$_3$based vairstors were investigated with cooling rate in the range of 2~8$^{\circ}C$/min. The cooling rate relatively weakly affected the microstructure, and the varistor voltage and the leakage current in the V-I chracteristics. But the nonlinear exponent relatively strongly affected by cooling rate. And the cooling rate also greatly affected the stability for DC stress. In gross, the varistors cooled with 4$^{\circ}C$/min exhibited the highest performance in the densification, nonlinearity, and stability. Especially, they exhibited a high stability, in which the variation rate of the varistor voltage and the nonlinear exponent is -1.44% and -4.85%, respectively, under more severe DC stress such as (0.80 V$_{1mA}$9$0^{\circ}C$/12 h)+(0.85 V$_{1mA}$115$^{\circ}C$/12 h)\`(0.90 V$_{1mA}$12$0^{\circ}C$/12 h)+(0.95 V$_{1mA}$1$25^{\circ}C$/12 h)+(0.95 V$_{1mA}$15$0^{\circ}C$/12 h). It should be emphasized that the stability of these varistors is much superior to that of others.s.of others.s.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.198-198
• /
• 2006

SnO2가 첨가된 In2O3(ITO) sputtering 타켓은 넓은 파장영역에서의 투광성과 높은 전기전도도의 특성 때문에 여러 종류의 평판형 디스플레이 제품에 사용되고 있다. 사용된 In2O3와 SnO2 분말은 높은 순도의 금속을 사용하였으며, 공질법을 이용하여 분말을 제조하였으며, 혼합된 In2O3-SnO2 분말은 하소조건과 소결조건에 따라 특성을 평가 하였다. 본 연구의 목적인 ITO sprttering 타켓의 SnO2 분산조건은 하소 온도가 증가함에 따라 분산성이 뛰어났으며, 조사된 30wt% 에서 5wt%로 SnO2의 함량이 감소함에 따라 분산성은 향상되었다. 이러한 결과들로부터 ITO 타켓 밀도와 SnO2의 분산성은 1150C 이상에서 휘발하는 SnO2의 량에 의해 크게 영향을 받는다.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book I
• /
• pp.352-373
• /
• 2003

Rhamnose-rich (RROP-s) and fucose-rich (FROP-s) oligo-and polysaccharides were prepared and extensively characterised by physical and chemical procedures [1,2] and compared to L-fucose. Their biological properties were then studied on human skin fibroblast cell cultures, human skin explant cultures and on hairless rat skin, using a variety of cell-biological, biochemical and computerised morphometrical procedures. Among the most important properties we could establish, the following are of particular interest for the tretment and prevention of age-dependent modifications of human skin (loss of skin-tissue, cells and matrix, wrinkle formation and others) : stimulation of cell proliferation (by $^3$[H]-thymidine incorporation and the MTT test), scavenging of reactive oxygen species (ROS) using several different procedures, and protease (MMP-2 and MMP-9) down-regulation. A topical preparation, using RROP-s and FROP-s, and/or L-fucose, was shown to increase cell proliferation, dermal matrix synthesis, efficient scavenging of ROS-s and to increase also the thickness of dermal tissue when applied for 4 weeks on hairless rat skin, accompanied by the densification of collagen bundles as well as by an increase of elastin synthesis. Using fluorescent labeled FROPs, it could be shown that these oligosaccharides react with cell-membrane receptors and especially with the elastin-laminin-receptor and the fucose-mannose receptor, but they penetrate also in the cell nucleus, suggesting the possibility of a direct action on the regulation of gene expression. When applied to the human skin of a team of voluntary women encompassing all age-groups, the efficiency of FROP-containing preparation could be confirmed using indentometry and computerised evaluation of skin micro-relief, as well as evaluation of periorbital wrinkles. It appears therefore that these preparations correspond to all the requirements of active anti-aging principles.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.58.1-58.1
• /
• 2011

WC-Co and other similar cemented carbides have been widely used as hard materials in industrial cutting tools and as mould metals; and a number of techniques have been applied to improve its microstructural characteristics, hardness and ear resistance. Cobalt is used primarily to facilitate liquid phase sintering and acts as a matrix, i.e. a cementing phase between WC grains. A uniform distribution of metal phase in a ceramic is beneficial for improved mechanical properties of the composite. WC-Co, starting from initial powders, is vastly used for a variety of machining, cutting, drilling, and other applications because of its unique combination of high strength, high hardness, high toughness, and moderate modulus of elasticity, especially with fine grained WC and finely distributed cobalt. In this study, that started with two different compositions of initial powders, WC-7.5wt%Co and WC-12wt%Co with initial powder size being 1~3 ${\mu}m$, magnetic pulsed compaction followed by subsequent vacuum sintering were carried out to produce consolidated preforms. Magnetic Pulsed Compaction (MPC), a very short duration (~600 ${\mu}s$), high pressure (~4 Gpa), high-density preform molding method was used with varied pressure between 0.5 and 3.0 Gpa, in order to reach an initial high density that would help improve the sintering behavior. For both compositions and varied MPC pressure, before and after sintering, changes in microstructural behavior and mechanical properties were analyzed. With proper combination of MPC pressure and sintering, samples were obtained with better mechanical properties, densification and microstructural behavior, and considerably improved than other conventional processes.

• 한국재료학회지
• /
• 제20권9호
• /
• pp.488-493
• /
• 2010

Geopolymer is a term covering a class of synthetic aluminosilicate materials with potential use in a number of areas, but mainly as a replacement for Portland cement. In this study, geopolymers with fly ash and meta kaolin were prepared using KOH as an alkali activator and water glass. The effect of water glass on the microstructures and the compressive strength of the geopolymer was investigated. As the amount of water glass increased, the dissolved inorganic binder particles in the geopolymers increased due to polymerization, resulting in a dense microstructure. The meta kaolin-based geopolymer showed a better extent of polymerization and densification than that of the fly ash-based geopolymer. XRD data also suggested that polymerization in meta kaolin-based geopolymers should be active resulting in the formation of an amorphous phase with an increasing amount of water glass. The compressive strength of the geopolymer was also dependent on the amount of water glass. The compressive strength of the geopolymers from both fly ash and meta kaolin increased with an increasing amount of water glass because water glass improved the extent of polymerization of the inorganic binder and resulted in a dense microstructure. However, the addition of water glass to the geopolymer did not seem to be effective for the improvement of compressive strength because the meta kaolin-based geopolymer mainly consisted of a clay component. For this reason, the fly ash-based geopolymer showed a higher value of compressive strength than the meta-kaolin geopolymer.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.172-183
• /
• 2016

Densification of the inner part of oil palm trunk (OPT) by the close system compression (CSC) method was performed in this study. The effects of the compression temperature and time on the anatomical, physical and mechanical properties of OPT were evaluated. The inner part of OPT with an initial average density of $0.3g/cm^3$ was used as samples. Oven-dried samples were immersed in water and vacuumed until fully saturated and then compressed by CSC at 120, 140, 160 or $180^{\circ}C$ for 10, 20, 30 or 40 min. The anatomical characteristics of transverse and radial sections before and after compression were compared by optical microscopy. The physical and mechanical properties, including the density, recovery of set (RS), modulus of elasticity (MOE), modulus of rupture (MOR), and compression parallel to grain were examined. It was observed that the anatomical characteristic of the inner part of OPT (i.e., vascular bundles, vessels, and parenchyma tissue) became flattened, fractured, and collapsed after compression by CSC. The RS decreased with increasing compression temperature and time. The lower RS indicated high dimensional stability. The physical and mechanical properties (i.e., density, MOR, MOE, and compressive strength) of the inner part of OPT increased with increasing compression temperature and time. Compression by the CSC method at $160^{\circ}C$ for 40 min was the optimum treatment.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.653-658
• /
• 1998

ZrO2, B2O3 및 AI을 사용하여 SHS법에 의한 붕화지르코늄을 합성을 하고 산화철과 알루미늄 분말의 첨가가 합성물의 치밀화에 미치는 영향에 대하여 검토하였다. 합성물중에 존재하는 결정상은 대부분이 ZrB2와 $\alpha$-AI2O3상이었다. 산화붕소와 알루미늄의 몰비가 1.0:3.3이상일 때 합성물의 치밀화는 크게 증가하였고, ZrB2 입자도$\alpha$-AI2O3용융상과 더불어 조대하였다. 산화철 1목에 대하여 알루미늄을 1-3몰을 첨가한 것과 산화철 1.5몰에 대하여 알루미늄을 3몰 첨가시 $\alpha$-AI2O3를 중심으로하는 슬라그상으로부터 용융상의 분이가 가능하였고, 이들 용융상에 존재하는 결정상은 ZrB2이외에 Fe, Fe2B, Zr2Fe상이었다. 용융상의 상대밀도는 산화철 1몰에 대하여 알루미늄을 1몰 첨가시 83.2%인 반면에 그 이상의 첨가량에 대해서는 치밀화는 크게 증가하여 알루미늄을 3몰 첨가한 경우 상대밀도는 93.7%로서 최대를 나타내었다.

• ETRI Journal
• /
• 제26권4호
• /
• pp.315-320
• /
• 2004

This paper proposes a 10-${\mu}m$ thick oxide layer structure that can be used as a substrate for RF circuits. The structure has been fabricated using an anodic reaction and complex oxidation, which is a combined process of low-temperature thermal oxidation (500 $^{\circ}C$ for 1 hr at $H_2O/O_2$) and a rapid thermal oxidation (RTO) process (1050 ${\circ}C$, for 1 min). The electrical characteristics of the oxidized porous silicon layer (OPSL) were almost the same as those of standard thermal silicon dioxide. The leakage current density through the OPSL of 10 ${\mu}m$ was about 10 to 50 $nA/cm^2$ in the range of 0 to 50 V. The average value of the breakdown field was about 3.9 MV/cm. From the X-ray photo-electron spectroscopy (XPS) analysis, surface and internal oxide films of OPSL prepared by a complex process were confirmed to be completely oxidized. The role of the RTO process was also important for the densification of the porous silicon layer (PSL) oxidized at a lower temperature. The measured working frequency of the coplanar waveguide (CPW) type short stub on an OPSL prepared by the complex oxidation process was 27.5 GHz, and the return loss was 4.2 dB, similar to that of the CPW-type short stub on an OPSL prepared at a temperature of 1050 $^{\circ}C$ (1 hr at $H_2O/O_2$). Also, the measured working frequency of the CPW-type open stub on an OPSL prepared by the complex oxidation process was 30.5 GHz, and the return was 15 dB at midband, similar to that of the CPW-type open stub on an OPSL prepared at a temperature of $1050^{\circ}C$ (1 hr at $H_2O/O_2$).

• 한국결정성장학회지
• /
• 제8권2호
• /
• pp.307-314
• /
• 1998

졸-겔법을 이용하여 PZT박막을 제조하였다. 출발물질로는 Pb-acetate trihydrate, Zr-normal propoxide와 Ti-ispropoxide를 사용하였으며, 용매로는 2-Methoxyethanol과 iso- Propanol을 사용하였다. 기판에 따른 Pb 이온 및 Si 이온의 확산을 고찰하기 위해 bare Si와 열산화된 $SiO_2/Si$ 그리고 산화된 기판 위에 졸-겔 spin-coating법으로 $TiO_2$를 입힌 $TiO_2/SiO_2/Si$ 기판을 사용하였다. 박막의 치밀화 및 기판과의 접착상태는 SEM을 이용하였고, 상생성 온도는 XRD, 그리고 Pb 이온 및 Si 이온의 확산 정도는 ESCA를 사용하였다. 기판으로 bare Si 및 $SiO_2/Si$를 사용한 경우, $700^{\circ}C$에서 perovskite상을 얻을 수 있었으며, SiO2/Si 기판을 사용하여 Si의 막으로의 확산을 다소 방지할 수 있었다. $TiO_2/SiO_2/Si$기판을 사용한 경우, $500^{\circ}C$에서 perovskite상을 얻을 수 있었고, Pb 이온 및 Si 이온의 확산을 방지할 수 있었다.

• 한국결정성장학회지
• /
• 제13권2호
• /
• pp.88-92
• /
• 2003

본 연구에서는, Mn-Co-Ni 산화물계 NTC 써미스터의 열처리 조건에 따른 전기적 특성간의 상호관계에 대하여 고찰하였으며, 이를 위해 XRD. 소결체 밀도측정 및 B정수, 저항 열방산정수 등의 전기적 특성치를 조사하였다. NTC 써미스터의 열처리 과정은 Mn-Co-Ni 산화물 시험편의 소결특성에 큰 영향을 미치고있었으며, 본 연구의 조성하에서는 $1250^{\circ}C$, 2시간 동안 열처리한 경우 가장 높은 밀도치를 얻을 수 있었다. 이 조건하에서 미세구조 관찰결과 치밀화과정이 거의 완전하게 이뤄짐을 확인하였다. 제조된 NTC 써미스터는 소결 온도가 상승함에 따라 저항값 및 B 정수값이 커지는 것을 확인하였으며, 연료 액위의 변화에 다른 출력전압의 거동을 측정한 결과 선형 감소 거동을 나타내었다. 따라서, 본 연구에서 제조된 Mn-Co-Ni 산화물계 NTC 써미스터의 전기적 특성은 열처리 조건과 밀접한 연관성이 존재하는 것으로 사료되며, 향후 자동차용 연료액위센서로의 응용성이 가능할 것으로 기대된다.