• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.2
• /
• pp.47-53
• /
• 1991

Recrystallization behaviors of ordered and disordered structures in $Ll_2$ type $Ni_3Fe$ alloy were studied through hardness measurement and differential thermal analysis. When the disordered structure was isothermally aged at $480^{\circ}C$ below order-disorder transition temperature, the hardness of the structure was increased due to progressive ordering with increasing aging time. The hardness of the disordered structure was increased rapidly with increasing deformation degree up to 10%, and then gradually increased with further deformation degree. while the hardness of the ordered structure was increased rapidly with increasing deformation degree up to 10%, showing a constant hardness value up to 50% and gradually decreased with further deformation degree. The hardness of the ordered structure was higher than that of the disordered structure at all same deformation degrees. The recrystallization temperature of the ordered and disordered structures were decreased with increasing deformation degree. At the same deformation degrees, the recrystallization temperature of the ordered structure was lower than that of the desordered structure.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.100-123
• /
• 1995

The relationship between plastic deformation and crystal grain change in warm forging processes of SM100 carbon steel is studied. If the carbon steel is deformed in warm forging temperature (about recrystallization range), the crystal grain and cementite of the internal part are changed, so material properties are changed. Some experimental values, such as the elliptic degree of cementite, the grain size of cementitie and ferrite grain size, are investigated. When the plastic deformation proceeds, the elliptic degree of cementite becomes large, the grain size of cementite particle is small, and the size of ferrite grain appears fine by recrystallization. The elliptic degree of cementite has a considerable effect on formability. The distribution of effective strain in the forging is calculated by the rigid visco-plastic FEM analysis. The effective strain distribution obtained from the FEM simulation is compared with the experimental result. At effective strain 0.3 dynamic recovery and dynamic recrystallization begin, over 2.5 the organization of material has better quality that is suitable for the following cold forming.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.2
• /
• pp.461-472
• /
• 1996

The relationship between plastic deformation and crystal grain change in warm forging processes of SM10C carbon steel is studied. If the carbon steel is deformed at warm forging temperature(about recrystallization range), material properties are changed due to microstructural chanre of the crystal grain and cementite of the internal part. Some experimental values are investigated in terms of the elliptic degree of cementite, the grain size of cementite and ferrite grain size. When plastic deformation proceeds, the elliptic degree of cementite becomes larger and the grain size of cementite particle becomes small. In addition, the size of ferrite grain becomes fines by recrystallization. The elliptic degree of cementite has a considerable effect on formability. The distribution of effective strain in the forging was calculated by the rigid visco-plastic FEM analysis. The effective strain distribution obtained from the FEM simulation is compared with the experimental result, At the level of effective strain 0.3, dynamic recovery and dynamic recrystallization begin and at the level of over 2.5, the organization of material has better internal structure that is suitable for the following cold forming.

• Korean Journal of Food Science and Technology
• /
• v.29 no.5
• /
• pp.939-946
• /
• 1997

Effects of moisture content on the gelatinization and recrystallization of non-waxy and waxy rice starch gels were investigated by differential scanning calorimetry (DSC). The recrystallization rates of the starch gels containing various moisture contents $(40{\sim}70%)$ were analyzed by Avrami equation. The waxy rice starch had higher gelatinization temperature and enthalpy than non-waxy one. The highest degrees of recrystallization in both rice starch gels stored at $4^{\circ}C$ were shown at 40%, and recrystallizations above 80% moisture content were not found. The degree of recrystallization of waxy one was higher than that of non-waxy one in the range of 40 to 60% moisture content. The Avrami exponents (n) of both rice starch gels were near to 1.0 and the time constant (1/k) was increased with increasing moisture content in the range of 40 to 70% moisture content. The recrystallization rate of waxy rice starch gel was slower than that of non-waxy one. The recrystallization of rice starch gels could be explained by the change of ice melting enthalpy during storage. The Wg's, represented the maximum practical amount of plasticizing water, were about 29.9% and 28.2% for non-waxy and waxy rice starch gels, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.150-156
• /
• 1996

The cold rolling of metal sheets leads to the formation of an inhomogeneous microstructure and texture. The type and sharpness of texture through the thickness and the degree of inhomogeneity depend on the friction between rolls the rolled material and the geometry of the rolling gap. In order to follow the effect of friction, two kinds of stecimens were prepared by applying with and without lubrication during the cold rolling. Although the deformed microstructure of the specimens rolled without lubrication was much inhomogenous than that of the specimens rolled with lubrication, the effect of lubrication on the cold rolling texture was not found. the recrystallization behavior was strongly dependent on the deformation process. Thus, the retardation of the recrystallization was observed in the specimens rolled without lubrication.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.191-199
• /
• 2001

The oxidation and recrystallization behaviors of Ni-base single crystal superalloy, CMSX-2 were investigated to determine the condition of the preparation for transient liquid phase (TLP) bonding operations. The faying surfaces of CMSX-2 were worked by the shot peening, fine cutting and mechanical polishing treatments and the degree of working of treated surfaces was evaluated by the hardness test and X-ray diffraction method CMSX-2 was heat-treated at 1,173∼1.589k for 3.6ks in vacuum of 4mPa. The mechanically polished surface was slightly oxidized after heat treatment even in the vacuum atmosphere of 4mPa. The thickness of an oxide film increased with increasing the heating temperature and the surface roughness of the faying surface. Recrystallization occurred at the surface after heat treatment at above 1,423K when the hardness was increased more than Hv600 by the shot peening treatment while the mechanically polished or fine cut surfaces didn't recrystallized. Based on these results, it was clearfied that the mechanically polishing with fine abrasive grit could be used for the preparation of faying surface of CMSX-2 before bonding operation.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.167-174
• /
• 2010

Recently the distributed topology control algorithm for constructing the Recrystallization Topology in the unstructured peer-to-peer network was proposed. In this paper, we prove that such a hierarchical topology is a scale-free power-law network. We present a model of a construction process of the distributed protocol, and analyze it based on a mean-field approximation and the continuum theory, so that we show that the constructed Recrystallization Topology is a scale-free network. In the proposed model, all nodes are born with some initial attractiveness and the system incorporates the rewiring of some links at every time step. Some old links are removed with the anti-preferential probability, and some new links are added with preferential probability. In other words, according to the distributed algorithm, each node makes connections to the more-preferential nodes having higher hit-ratio than other nodes, while it disconnects the anti-preferential nodes having lesser hit-ratio. This gives a realistic description of the local processes forming the recrystallization topology in unstructured peer-to-peer network. We calculate analytically the degree distribution. The analytic result indicates that the constructed network is a scale-free network, of which the scaling exponent is 3.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.1
• /
• pp.18-23
• /
• 2005

Effect of cold rolling on microstructural changes has been investigated for a Zn-15%Al alloy to elucidate the reason for its work softening behavior. Fully annealed microstructure of the Zn-15%Al alloy is characterized by ${\eta}$ grains and (${\eta}+{\alpha}$) lamellar colonies, where ${\eta}$ and ${\alpha}$ are Zn-rich HCP and Al-rich FCC phases, respectively. The hardness decreases continuously with increasing cold rolling degree, exhibiting work softening behavior. It is revealed that during the cold rolling, (${\eta}+{\alpha}$) lamellar colonies gradually change into equiaxed ${\eta}$ and ${\alpha}$ grains due to dynamic recrystallization at room temperature, while pre-existing ${\eta}$ grains are only deformed without recrystallization. Furthermore, cold rolling causes the precipitation of dissolved Al solutes in ${\eta}$ grains. In view of these results, change of (${\eta}+{\alpha}$) phases from lamellar to equiaxed morphology, which results in structural softness and increase in equiaxed ${\eta}/{\alpha}$ grain boundaries with higher mobility, and deterioration of solution hardening by precipitation of Al solutes from ${\eta}$ grains, are thought to contribute to the work softening of Zn-15%Al alloy.

• Journal of the Korean earth science society
• /
• v.24 no.5
• /
• pp.402-410
• /
• 2003

When the bivalve fossil microstructure is observed on a thin section, the growth lines of the older specimens are mostly erased by calcite recrystallization while those of the younger are well preserved in detail. During the fossil diagenesis, the shells tend to darken gradually since the valve-forming component Ca$^{2+}$ is the replaced by the surrounding materials Fe$^{2+}$, Mg$^{2+}$, and Mn$^{2+}$. Therefore, the metallic ratio against Ca component in fossil was increased during diagenesis. The UV-Visible spectrophotometry analysis shows that the reflecting degree is low level in Cretaceous bivalve fossils in contrast to the Tertiary and Recent ones. This result suggests that the dark color in older bivalve fossils is affected by the replacement of the metal ions.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2582-2590
• /
• 2021

The high-energy milling is one of the most extended techniques to produce Oxide dispersion strengthened (ODS) powder steels for nuclear applications. The consequences of the high energy mill process on the final powders can be measured by means of deformation level, size, morphology and alloying degree. In this work, an ODS ferritic steel, Fe-14Cr-5Al-3W-0.4Ti-0.25Y₂O₃-0.6Zr, was fabricated using two different mechanical alloying (MA) conditions (M_std and M_act) and subsequently consolidated by Spark Plasma Sintering (SPS). Milling conditions were set to evidence the effectivity of milling by changing the revolutions per minute (rpm) and dwell milling time. Differences on the particle size distribution as well as on the stored plastic deformation were observed, determining the consolidation ability of the material and the achieved microstructure. Since recrystallization depends on the plastic deformation degree, the composition of each particle and the promoted oxide dispersion, a dual grain size distribution was attained after SPS consolidation. M_act showed the highest areas of ultrafine regions when the material is consolidated at 1100 ℃. Microhardness and small punch tests were used to evaluate the material under room temperature and up to 500 ℃. The produced materials have attained remarkable mechanical properties under high temperature conditions.