• 월간 기계설비
• /
• s.115
• /
• pp.76-78
• /
• 2000

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.10
• /
• pp.879-886
• /
• 2016

Tractrix dies, used in the deep drawing process, can be used to form CNG pressure vessels without a blank holder. Previous studies had only applied tractrix profiles to perform the first deep drawing process of DDI; but an optimal design of the tractrix die that focuses on improving die life and reducing production cost has not been performed yet. In this study, finite element analyses of deep drawing processes were conducted according to heights of the tractrix die by using translating asymptotes. In addition, researchers analyzed von-Mises stresses at the part of stress concentration of the die according to the forming punch loads in order to propose an optimal tractrix die design.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.51-61
• /
• 1993

A systematic approach of the energy method is proposed for analysis of axisymmetric deep drawing in which the total deforming region is divided into five sections by the geometric characteristic. The corresponding solution is found through optimization of the total energy dissipation with respect to some parameters assumed in the kinematically admissible velocity field defined over each region. The sheet blank is divided into three-or five-layers to consider the bending effect. For the evaluation of frictional energy, it is assumed that the blank holding force acts on the outer rim of the flange and that the contact pressure acting on punch shoulder or die shoulder has uniform distributions, respectively. The computed results by the present method are compared with the experiment and the computed results by the elastic-plastic finite element method for the distribution of thickness strain and the relation between the punch stroke and punch load. The results for the case of multi-layers show better agreements than for the case of a single layer in load vs. stroke relation and strain distribution. It is thus shown that the multi-layer technique can be effectively employed in analyzing axisymmetric deep drawing in connection with the energy method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1425-1432
• /
• 2006

Coating layers on a coated sheet steel frequently affect distributions of strain rate of sheets and deteriorate the frictional characteristics between sheets and tools in sheet metal forming. Thus, it is important to identify the deformation behavior of these coatings to ensure the success of the sheet forming operation. In this study, the technique using nano-indentation test, FE-simulation and Artificial Neural Network(ANN) were proposed to determine the power law stress-strain behavior of coating layer and the power law behavior of extracted coating layers was examined using FE-simulation of drawing and nano-indentation process. Also, deep drawing test was performed to estimate the formability and frictional characteristic of coated sheet, which was calculated using the linear relationship between drawing force and blank holding force obtained from the deep drawing test. FE-simulations of the drawing process were respectively carried out for single-behavior FE-model having one stress-strain behavior and for layer-behavior FE-model which consist of coating and substrate separately. The results of simulations showed that layer-behavior model can predict drawing forces with more accuracy in comparison with single-behavior model. Also, mean friction coefficients used in FE-simulation signify the value that can occur maximum drawing force in a drawing test.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03a
• /
• pp.26-29
• /
• 1999

Process design for elliptically shaped deep drawing products is various according to size shape and specification of products. This study presents two approaches to design the preform that is a key process for elliptically shaped products, One of these is that cross-section of punch is circular. Another is that for the improvement of characteristics for final products the cross-section of the punch is similar to rectangular shape. After forming the preform process design of top-part drawing is the same. In the study blank shape and dimension are obtained by applying a numerical formula and surface area constancy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.85-88
• /
• 2001

Examination of the die design is carried out for a multi-stage rectangular cup drawing process with the large aspect ratio with the aid of the finite element analysis. The analysis considers the deep drawing process with the ironing process for the thickness control in the cup wall. Simulation is performed to investigate the deformation mechanism in the initial design and the modified design. The analysis clarifies that the irregular cross section and the irregular contact condition produces unfavorable deformation. The analysis results show that the modified design improves the quality of a deep-drawn product with the low possibility of failure. The analysis result also shows good agreement with the experimental one.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.111-118
• /
• 1999

This article describes the basic engineering concepts to be considered in the application of an induction heating furnace in the hot-dip galvanizing line. Experience in the Dongkuk project in Pohang, has shown that this arrangement has many advantages over the conventional method of using a combustion-gas heated furnace. Investment and operating costs are lower, the line length is much shorter, line operation is more convenient, air pollution is reduced, and the coated strip at of top-quality. As these benefits become well known, it is anticipated that the concept of induction heating will be more widely used in both new and revamped process lines. Induction heating is suitable for the production of Commercial Quality hot galvanized coils. More research is required to extend the present concept to the production of higher forming grades such as Drawing, Deep Drawing and Extra Deep Drawing Quality steels. A combination of induction heating and combustion-gas heating may lead to the way to the processing of these qualities of strip.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.653-661
• /
• 2009

In order to reduce the noise and oscillation, it is consider a matter in all aspects about the noise stem from accumulator and the characteristic of transmission, Transformation of outside shape has change of noise occurrence at transmission process. Therefore, performed sound numerical analysis and conducted an experiment to examine the birthplace of accumulator's external shape change. In a sound numerical analysis, we can fond out transmission loss between inlet and outlet's sound pressure. In an experiment, we can make out transmission loss by sound wave separation theory through drawing sound pressure inlet and outlet.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.4
• /
• pp.86-91
• /
• 2000

Numerical simulation of sheet metal forming for panels as other components has wide acceptance in the automotive industry. Therefore this paper was focused in the drawability factors (which are friction coefficient , radius of die and punch ) on the square cup deep drawing by the explicit finite elements code $PAM-STAMP^{TM}$. The computed results are compared with the experimental results to show the validity of the analysis. In order to compare the simulation results with the experiment results and predict the effect of drawability factors, the relationships between punch load punch stroke, and the relationships between thickness strain and distance are used. According to this study, the results of simulation by using $PAM-STAMP^{TM}$ will give engineers good information to access the drawability of square drawing.

• Transactions of Materials Processing
• /
• v.20 no.1
• /
• pp.36-41
• /
• 2011

Meso-scale or micro-scale forming of sheet metal parts has been recently considered as one of the important forming technologies with growing demand on meso/micro products for electric or medical devices. Experimental investigation on the cylindrical meso-cup drawing with hemispherical punch is carried out to examine the limit drawing ratio and thickness distribution of drawn cups. The working parameters chosen in this study are blank diameter, die-corner radius and blankholding force. It is found from the experiments that the limit drawing ratio of 2.4 can be achieved in the case of hemispherical cup drawing and uniform thickness distribution in wider region can be obtained compared with the results of conventional cup drawing.