• 대한기계학회논문집A
• /
• 제20권12호
• /
• pp.3728-3740
• /
• 1996

High-quality cups of deep drawing ratio of more than four cannot be simply drawn by conventional drawing and redrawing processes. In the present study, after the first deep drawing process, subsequent hydromechanical reverse redrawing with controlled radial pressure is employed. In order to increase the deep drawing ratio up to muchmore than four, the radial pressure should be controlled independently of the chamber pressure and thus an optimum forming condition can be found easily by varying the radial pressure. The process has been subjected to finite element analysis by using the rigid-platic material modeling considering all the frictional conditions induced by the hydrostatic pressure. In order to consider the pressure effect on the sheet, the pressure distributions on the flange part and the side wall part are calculated mumerically from simplified Navier-stokes equation. The comparison of the computation with the experiment has shown that the finite element modeling can be conveniently emplyed for the design of the process with reliability from the viewpoint of formability.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.407-410
• /
• 2005

The drawability of AZ31B magnesium sheet is estimated according to the variable temperatures (200, 250, 300, 350 and $400^{\circ}C$), forming speed (20, 50, 100 mm/min), thickness (0.8, 1.4 t), blank holding force (1.0, 1.4, 1.7kN). The deep drawing process (DDP) of circular cup is used in forming experiments. The results of deep drawing experiences show that the drawability is well at the range from 250 to $300^{\circ}C$, 50mm/min forming speed and 1.4kN blank holding force. The 0.8t magnesium sheets were deformed better than 1.4t. BHF was controlled in order to improve drawability and protect the change of cup thickness. When BHF was controlled, tearing and thickness change were decreased and LDR. was improved from 2.1 to 3.0.

• 소성∙가공
• /
• 제21권4호
• /
• pp.258-264
• /
• 2012

The forming failure of AZ31 alloy sheet during deep drawing processes was predicted by the FEM and ductile fracture criteria. Uniaxial tensile tests of round-notched specimens and FE simulations were performed to calculate the critical damage values for three ductile fracture criteria. The critical damage values for each criterion were expressed as a function of strain rate at various temperatures. In order to determine the best criterion for failure prediction, Erichsen cupping test under isothermal conditions at $250^{\circ}C$ were conducted. Based on the plastic deformation histories obtained from the FE analysis of the Erichsen cupping tests and the critical damage value curves, the initiation time and location of fracture were predicted under bi-axial tension deformation. The results indicate that the Cockcroft-Latham criterion had good agreement with the experimental data. In addition, the FE analysis combined with the criterion was applied to another deep drawing process using an irregular shaped blank and these additional results were verified with experimental tests.

• Design & Manufacturing
• /
• 제17권4호
• /
• pp.8-13
• /
• 2023

In this study, it was studied whether a new measurement factor "frictional vibration" that occurs due to the material flow of the die and sheet metal in the flange area during deep drawing process, could be measured using an vibration sensor. The blank holder force acting on the flange area during drawing processing acts as a friction force in the opposite direction into which the sheet material flows and causes friction vibration. As the blank holder force increases, the friction force increases, and as the blank holder force decreases, the friction force also decreases. Because of this, friction vibration also increases and decreases in proportion to the size of the blank holder force. According to this theory, whether frictional vibration occurs was measured using a flange simulator and a vibration sensor. The initial pressure was created using a torque wrench, and it was confirmed that the amplitude increased by about 4 times when torque 6 Nm was increased. When the forming velocity was rapidly changed to 300 mm/min, the amplitude increased approximately 4 times. It was confirmed that the amplitude of frictional vibration according to the measurement location was greater the further away from the specimen. It was verified that a new measurement factor "friction vibration" in the flange area can be measured and used for online monitoring.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.89-93
• /
• 2001

This study was carried out to investigate the warm deep drawability of square cups of clad sheet metals, by changing temperatures of die and blankholder and blank materials. Two kinds of clad sheet metals, STS304-A1050-STS304 and STS304-A1050-STS430 were chosen for experiments. The relative drawing depth of STS304-A1050-STS304 clad sheet was increased up to 4.4 at $150^{\circ}C$ that was $29\%$ higher than at room temperature, whereas STS304-A1050-STS430 material was improved to 3.65 at $120^{\circ}C$ which was $16\%$ better than at room temperature. In addition, comparison of wall thickness and hardness of a warm drawn cup with those of room temperature showed more even distributions. Therefore, warm forming technique was confirmed to ive better results in deep drawing of stainless clad sheet metal.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.109-117
• /
• 1994

This paper describes a method and a system for automatic generation of flanged cylinderical deep drawing process outlines. A process outline is a sequence of operation leading from the blank to the required finished part. The input is the dimension of final product and the output is the effective process outline to manufacture the product. That system is programmed by PROLOG language and is composed of facts and rules of manufacturing knowledge hierarchically.

• 소성∙가공
• /
• 제6권5호
• /
• pp.416-424
• /
• 1997

In the present study, a contact search and check algorithm for general tool surface described by triangular FE patch is proposed. To improve numerical stability, SEAM element using the linear Coons interpolation has been used. To check the proposed algorithm, both clover cup and L-shape cup deep drawing processes are calculated. The computed results shows that the proposed contact algorithm can be successfully applied for sheet metal forming processes with general shaped tools.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.219-220
• /
• 2011

• 한국컴퓨터정보학회논문지
• /
• 제27권12호
• /
• pp.59-68
• /
• 2022

본 논문은 주어진 현품 영상과 도면 영상의 유사도를 비교하여 1:1 검증을 위한 방법을 제시한 것으로, CNN(Convolutional Neural Network) 기반의 딥러닝 모델을 두 개로 결합하여 Siamese Net을 구성하고 현품 영상과 도면 영상(정면도, 좌우 측면도, 평면도 등)을 같은 제품이면 1로 다른 제품이면 0으로 학습하며, 추론은 현품 영상과 도면 영상을 쌍으로 질의하여 해당 쌍이 같은 제품인지 아닌지를 판별하는 딥러닝 모델을 제안한다. 현품 영상과 도면 영상과의 유사도가 문턱 값(Threshold: 0.5) 이상이면 동일한 제품이고, 문턱 값 미만이면 다른 제품이라고 판별한다. 본 연구에서는 질의 쌍으로 동일제품의 현품 영상과 도면 영상이 주어졌을 때(긍정 : 긍정) "동일제품"으로 판별할 정확도는 약 71.8%로 나타났고, 질의 쌍으로 다른 현품 영상과 도면 영상이 주어졌을 때(긍정: 부정) "다른제품"으로 판별할 정확도는 약 83.1%를 나타내었다. 향후 제안한 모델에 파라미터 최적화 연구를 접목하고 데이터 정제 등의 과정을 추가하여 현품 영상과 도면 영상의 매칭 정확도를 높이는 연구를 진행할 예정이다.

• 소성∙가공
• /
• 제11권8호
• /
• pp.716-723
• /
• 2002

A systematic investigation for the process design in deep drawing is necessary to improve the quality of drawn cups. This study concentrates mainly on the influence of process desing scheme on the product qualities in cylindrical cup drawing. Three types of process design scheme were chosen in this study. Case 1 is to draw a finished cup of 50mm in diameter in one stage, Case 2 and Case 3 are redrawing the first drawn cups of 55, 65mm in diameter to the final size respectively. Through experiments the maximum drawing force in two-stage cup drawing can be reduced up to 24% as compared with that of one-stage cup drawing. In addition, Case 3 process results in better product qualities than the other two processes in terms of the distributions of thickness and hardness.