• Geomechanics and Engineering
• /
• v.5 no.5
• /
• pp.419-445
• /
• 2013

This paper presents an experimental study on the influence of principal stress direction and magnitude of intermediate principal stress on the undrained stress-strain-strength behaviors of Bangkok Clay. The results of torsional shear hollow cylinder and advanced triaxial tests with various principal stress directions and magnitudes of intermediate principal stress on undisturbed Bangkok Clay specimens are presented. The analysis of testing results include: (i) stress-strain and pore pressure behaviors, (ii) stiffness characteristics, and (iii) strength characteristics. The results assert clear evidences of anisotropic characteristics of Bangkok Clay at pre-failure and failure conditions. The magnitude of intermediate principal stress for plane-strain condition is also investigated. Both failure surface and plastic potential in deviatoric plane of Bangkok Clay are demonstrated to be isotropic and of circular shape which implies an associated flow rule. It is also observed that the shape of failure surface in deviatoric plane changes its size, while retaining its circular shape, with the change in direction of major principal stress. Concerning the behavior of Bangkok Clay found from this study, the discussions on the effects of employed constitutive modeling approach on the resulting numerical analysis are made.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2423-2430
• /
• 1994

Several factors of the efficient combustion process are shape of combustion chamber, position of spark plug, turbulence flow and so on. the shape of combustion chamber and position of spark plug are constrained to geometrically, and then it could not make a change the shape easily. But the turlence flow in combustion chamber have a great influence on combustion phenomena, and which is much easier to control relatively. And since characteristics of turbulence flow would be very important to the stability of combustion and performances, This study is also essential to future engine-low emission and lean burn engine. This paper shows that the visualization of the turbulence flow of single cylinder engine by using 2way, $45^{\circ}$ inclined and 2 channel hot wire probe through the park plug hole. We also study the characteristics of turbulence flow by means of ensemble averaged mean velocity, turvulence intensity and integral length scale.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.86-101
• /
• 2021

This study examined the effects of buoy shape and Nonlinear Froude-Krylov force (NFK) on a heaving-buoy-type Wave Energy Converter (WEC). Based on the Maclaurin expansion, the theoretical solutions of the NFK were derived for three different buoy shapes; hemispheric buoy, circular vertical cylinder, and truncated conical cylinder. A hydraulic power take-off system was adopted, and the latching control strategy was applied to maximize the extracted power from the WEC. The nonlinear effects of the Froude-Krylov force and restoring force on the heaving point absorber were investigated by comparing the heave Response Amplitude Operator (RAO) and time-averaged power extraction. The results showed that the conventional linear analyses were overestimated by up to 50% under the high amplitude wave condition. The latching control strategy was the most effective when peak wave period of regular or irregular wave was 0.4-0.45 times the heave natural period of the buoy.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1979-1989
• /
• 1992

An experimental study has been performed to investigate the horseshoe vortex system formed around cylindrical obstacles mounted vertically on the surface over which a boundary layer is formed. To measure the mean velocity of the flow field, a five-hole Pitot tube has been used. In addition, surface static pressure measurements and surface flow visualization were also performed. From the five-hole probe measurements, vorticity distribution was deduced numerically and the streamwise velocity distribution was also examined. To consider the effect of the leading-edge shape on the formation of the horseshoe vortex, a qualitative comparison was made between the three-dimensional flows around a circular cylinder and a wedge-type cylinder. The five-hole probe measurements showed a single primary vortex which exists immediately upstream of the obstacles, and endwall flow visualization showed the existence of a corner vortex. As the vortex passes around the obstacle, the vortex strength is reduced and the vortex core moves radially outward. Due to this horseshoe vortex, the fluid momentum is found to decrease along the streamwise direction. Since the horseshoe vortex formed around a wedge-type cylinder has weaker strength and is confined to a narrower region than that around a circular, the possibility that the secondary flow loss due to the horseshoe vortex can be reduced through a change of the leading- edge shape is proposed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1169-1174
• /
• 2013

Most products are indeed governed by multiple failure modes. However, there are few cases in which reliability analysis applies to only one failure mode at a time. Furthermore, reliability data do not include information about failure modes, or the reliability analysis is performed using a representative failure mode. The Weibull shape parameter for failure modes is more important than one for products in the reliability qualification test. This paper presents reliability analysis methods for a mechanical component with multiple failure modes. These methods include the competing failure modes (CFM) method and the mixed Weibull method. Pneumatic cylinder test data with three failure modes are presented to estimate the shape parameter for each separate failure mode. In addition, reliability measures (B10 life, characteristic life) of the pneumatic cylinder considering three failure modes were compared with those assuming a single failure mode.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.11
• /
• pp.1077-1084
• /
• 2017

Camshaft engines designed for constant engine loads have been applied to existing marine diesel engines. However, due to environmental regulations, electro-hydraulic servo mechanisms, which have a loaddependent cylinder liner jacket water cooling system (LDCL-JWCS), have been recently developed to individually control the temperature of the cylinders depending on the engine load. In this system, the 3-way valve, which prevents low temperature corrosion by reducing the temperature difference between the upper and lower parts of the cylinder, has been employed, but the outlet mass flow of the existing valve is low. In this study, the design of the internal shape of the 3-way valve was performed by analyzing the effects of the design parameters of the valve shape on the performance (i.e., the outlet mass flow rate and temperature). The proposed model was verified by comparing its performance to that of existing marine diesel engine valves.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.2
• /
• pp.95-105
• /
• 2022

In this study, the fishery status of the octopus pot fishery in the east coastal sea were investigated, and the fishing performance of each pot shape was compared and analyzed. The fishery status survey was conducted through listening surveys at Jukbyeon Port, Uljin Port and Pohang Daebo Port in Gyeongbuk Province, and the amount of fishing gear used, fishing method, size and loss of octopus pot fishery was investigated. On the east coastal sea, octopus is one of the commercially important fish stocks and is caught in inshore pots, inshore combos, inshore gillnets and offshore pots. Among these fishing methods, pot fishing yields the highest catch. The shape of the pot differs depending on the region. In Uljin (Jukbyeon Port and Hupo Port), Gyeongbuk, rectangular type net pots are mainly used, and in Pohang (Daebo Port) in Gyeongbuk, drum-type pots are mostly used. Enteroctopus dofleini accounts for more than 90% of the catch of octopus. For the octopus fishing performance test by trap type, three types of traps (rectangular pot, drum pot and cylinder pot) were used on the coastal sea of Pohang Daebo. As a result, the total catch by pot shape was shown in the order of rectangular-type pot > drum-type pot > cylinder-type pot. The catch of octopus, the target species, was in the following order: rectangular-type pot > drum-type pot > cylinder-type pot. Such result shows a significant difference (Mann-Whitney test, p<0.05).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.135-140
• /
• 2021

In this study, the concrete aggregate shape features were extracted from the cross-section of a normal concrete strength cylinder, and the compressive strength of the cylinder was predicted using artificial neural networks and image processing technology. The distance-angle features of aggregates, along with general aggregate shape features such as area, perimeter, major/minor axis lengths, etc., were numerically expressed and utilized for the compressive strength prediction. The results showed that compressive strength can be predicted using only the aggregate shape features of the cross-section without using major variables. The artificial neural network algorithm was able to predict concrete compressive strength within a range of 4.43% relative error between the predicted strength and test results. This experimental study indicates that various material properties such as rheology, and tensile strength of concrete can be predicted by utilizing aggregate shape features.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.175-184
• /
• 2003

A method of the shape design sensitivity analysis based on the boundary integral equation formulation is presented for two-dimensional inhomogeneous thermal conducting solids with multiple domains. Shape variation of the external and interface boundary is considered. A sensitivity formula of a general performance functional is derived by taking the material derivative to the boundary integral identity and by introducing an adjoint system. In numerical analysis, state variables of the primal and adjoint systems are solved by the boundary element method using quadratic elements. Two numerical examples of a compound cylinder and a thermal diffuser are taken to show implementation of the shape design sensitivity analysis. Accuracy of the present method is verified by comparing analyzed sensitivities with those by the finite difference. As application to the shape optimization, an optimal shape of the thermal diffuser is found by incorporating the sensitivity analysis algorithm in an optimization program.

• Composites Research
• /
• v.17 no.5
• /
• pp.1-6
• /
• 2004

Composite pressure vessels with HDPE (high density polyethlyne) liner with metal boss at each end were developed by Filament Winding Process. The vessel is composed of a dome-shaped part at each end and a cylinder-shaped part at the middle of the vessel. The environmental tests carried out for possible vessel materials such as High Density Polyethlyn (HDPE), resins and reinforcing fibers up to a year showed no significant damages. The boss was designed to minimize the gas leak which was verified by FEM analysis. Most ideal fiber tension was obtained by experimental method and the fiber volume fraction, $\textrm{V}_{f}$, obtained by image analyzer were 55.4 % in cylinder and 55.6 % in dome parts, respectively. Winding pattern is programmed to control the composite thickness in the dome areas such that the failure of the vessel may occur in the cylinder. During the cure, the vessel was rotated and a constant internal pressure of 0.62 bar was applied. From this, the vessel's burst pressure is improved by 28 %. The burst and fatigue tests for under-wound and fully wound vessel showed satisfactory results.