• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.62-69
• /
• 1999

The advantages of Thermal sprayed coatings as a replacement for cast iron liners are reduced weight, better heat transfer and reduced cost. One of the most important performance attributes of a cylinder bore coating is its wear resistance, since it must survive the abrasive sliding of both the piston rings and the piston skirt. In this study, composite powders were prepared by ball milling of Al-13Si-3Mg(wt%) alloy with SiC particles. The concentrations of SiC were 40 and 60wt%. The composite powders were sprayed using Metco-9MB plasma torch. Plasma sprayed coatings were heat-treated at 500℃ for 3 hours. The wear resistances of the plasma sprayed coatings were found to improve with heat treatment and superior to the commercially available G.C.I.(gray cast iron). AlSiMg-40SiC heat-treated coatings showed the best wear resistance in this study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.77-85
• /
• 1995

Among mechanical friction losses in an engine, the piston assembly and cylinder components accounts for the majority of the losses. The movable bore technique has been developed and turned out to be the most reliable technique in measuring the instantaneous friction of piston assembly. The weakness of this system, however, was the presence of the protruded top of movable bore necessary for pressure balancing. Because of the protruded part the piston could not be taken out without disassembling the crankshaft. Present study was carried out with a system of removable top of the movable bore so that it was possible to make frequent piston removals. The effects from engine speed, oil viscosity, engine load and elastic contact pressure of piston rings on the frictional characteristics have been evaluated with the improved equipment. Also, frictions of each member of piston assembly were measured.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.7-15
• /
• 2008

In manufacturing aircraft, safety and lightness of structure are important factors. Utilizing autofrettage technique, these benefits can be obtained. This technique is most frequently applied to a single cylinder. However, the Bauschinger effect reduces the benefits of autofrettage process Therefore, there is increasing interest in the use of compound cylinder that combine shrink fit and autofrettage. In this paper, single and compound cylinders that has same geometry were considered. It was found that compound cylinder which was autofrettaged has lower tangential hoop stress and plastic strain than single cylinder at bore. This means a reduction in the impact of the Bauschinger effect after shrink-fitting which produces the beneficial bore hoop stress.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.77-82
• /
• 2011

The piston-cylinder mechanism is widely adopted in the hydraulic machine components. In these cases, the hydrodynamic pressures are generated in the clearance gap between the piston and cylinder under lubrication action of the piston. Under the eccentric and tilted condition of the piston in the cylinder bore, the non-symmetric pressure distributions in the circumferential direction result in lateral forces. When the lateral forces act as increasing the eccentricity and tilting ratios, excessive wear can be result in cylinder and piston which are well known 'hydraulic locking' phenomena. In this paper, the hydrodynamic pressures generated in the clearance are measured using a stationary piston and moving cylinder apparatus. The experimental results showed that the hydrodynamic pressure distributions are highly affected by the speed and eccentricity of the cylinder and the oil viscosity.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.13-14
• /
• 2006

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 1999.11a
• /
• pp.16-20
• /
• 1999

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2000.06a
• /
• pp.43-46
• /
• 2000

• Journal of Auto-vehicle Safety Association
• /
• v.6 no.1
• /
• pp.33-40
• /
• 2014

In this study the cylinder liner deformation which is one of the most influencing factors in a diesel engine oil consumption was performed by the finite element analysis on the basic designed structure consisting of the cylinder block, head and liners under the conditions of assembly, thermal and gas loads. Compared with a large number of other cylinder blocks showing remarkable harmonic orders of the liner distortion, results are excellent. Namely. the higher harmonic order amplitudes of the radial liner deformation amount to 1 ~ 2㎛ maximally. The main reason lies in the relatively large wall thickness of the liner which amounts to 8.2% of the bore diameter. Besides, a very stiff and symmetrical cylinder block design in combination with a bolt force introduction approximately 1.5mm below the block top deck have a further share on these results. Therefore excellent low oil consumption can be expected.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.7 s.262
• /
• pp.800-807
• /
• 2007

Autofrettage process is used for internal forming and sizing of cylinder designed to withstand high internal pressures. Once the tube is autofrettaged, it needs to be machined to its final dimensions both at the bore and its outer surface. This paper presents an analytical analysis and numerical analysis of machined compound cylinder using finite element code, ANSYS10.0. An analytical model for predicting the level of autofrettage following either inner, outer, or combined machining of the compound cylinder is developed for the autofrettage residual stress field is simulated by an autofrettaged pressure. The autofrettaged pressures are obtained by using trying-error method. As autofrettage percentage is 20 % and 40 %, the numerical results are found to be in almost agreement with the analytical ones. However, as autofrettage percentage is 60 %, the numerical results have a little difference with the analytical ones.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.620-625
• /
• 2007

Autofrettage process is used for internal forming and sizing of cylinder designed to withstand high internal pressures. Once the tube is autofrettaged, it needs to be machined to its final dimensions both at the bore and its outer surface. This paper presents an analytical analysis and numerical analysis of machined compound cylinder using finite element code, ANSYS10.0. An analytical model for predicting the level of autofrettage following either inner, outer, or combined machining of the compound cylinder is developed for the autofrettage residual stress field is simulated by an autofrettaged pressure. The autofrettaged pressures are obtained by using trying-error method. As autofrettage percentage is 20 %, the numerical results are found to be in almost agreement with the analytical ones. However, as autofrettage percentage is 60 %, the numerical results have a little difference with the analytical ones.