• Structural Engineering and Mechanics
• /
• 제28권5호
• /
• pp.495-514
• /
• 2008

In this paper, experimental and theoretical investigations of the effect of the mean moment on the response and collapse of circular thin-walled tubes subjected to cyclic bending are discussed. To highlight the influence of the mean moment effect, three different moment ratios r (minimum moment/ maximum moment) of -1, -0.5 and 0, respectively, were experimentally investigated. It has been found that the moment-curvature loop gradually shrinks with the number of cycles, and becomes stable after a few cycles for symmetric cyclic bending (r = -1). However, the moment-curvature loop exhibits ratcheting and increases with the number of cycles for unsymmetric cyclic bending (r = -0.5 or 0). In addition, although the three groups of tested specimens had three different moment ratios, when plotted in a log-log scale, three parallel straight lines describe the relationship between the controlled moment range and the number of cycles necessary to produce buckling. Finally, the endochronic theory combined with the principle of virtual work was used to simulate the relationship among the moment, curvature and ovalization of thin-walled tubes under cyclic bending. An empirical formulation was proposed for simulating the relationship between the moment range and the number of cycles necessary to produce buckling for thin-walled tubes subjected to cyclic bending with different moment ratios. The results of the experimental investigation and the simulation are in good agreement with each other.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.190-197
• /
• 2000

A moment-curvature relationship to simulate the behavior of reinforced concrete beam under cyclic loading is introduced. Unlike previous moment-curvature models and the layered section approach, the proposed model takes into consideration the bond-slip effect by using monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The advantages of the proposed model, comparing to layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures. The modification of the moment-curvature relation to reflect the fixed-end rotation and pinching effect is also introduced. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed model.

• Structural Engineering and Mechanics
• /
• 제34권3호
• /
• pp.367-376
• /
• 2010

In this paper, an experimental investigation of the mechanical behavior and buckling failure of sharp-notched circular tubes subjected to cyclic bending is discussed. The unnotched and sharp-notched circular tubes of SUS 304 stainless steel were tested under symmetric curvature-controlled cyclic bending. It was found from moment-curvature curves that the loops show cyclic hardening and gradually steady after a few cycles for all tested tubes. The ovalization-curvature curves show an unsymmetric, ratcheting and increasing manner with the number of cycles. In addition, it was found that six almost parallel lines corresponding to unnotched and five different notch-depth (0.2, 0.4, 0.6, 0.8 and 1.0 mm) tubes were noted from the experimental relationship between the cyclic controlled curvature and the number of cycles necessary to produce buckling on a log-log scale. An empirical formulation was proposed so that it could be used for simulating the aforementioned relationship. By comparing with the experimental finding, the simulation was in good agreement with the experimental data.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.3-11
• /
• 2002

A moment-curvature relationship to simulate the behavior of reinforced concrete (RC) columns under cyclic loading is introduced. Unlike previous moment-curvature models and the layered section approach, the unposed model takes into account the bond-slip effect by using a monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The pinching enact caused by axial force is considered with an assumption that the absorbing energy corresponding to any deformation level maintains constant regardless of the magnitude of applied axial force. The advantages of the proposed model, comparing tn layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures.. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed mood.

• Structural Engineering and Mechanics
• /
• 제60권3호
• /
• pp.387-404
• /
• 2016

In this paper, the response and failure of sharp-notched 6061-T6 aluminum alloy circular tubes with five different notch depths of 0.4, 0.8, 1.2, 1.6 and 2.0 mm subjected to cyclic bending were experimentally and theoretically investigated. The experimental moment-curvature relationship exhibits an almost steady loop from the beginning of the first cycle. And, the notch depth has almost no influence on its relationship. However, the ovalization-curvature relationship exhibits a symmetrical, increasing, and ratcheting behavior as the number of cycles increases. In addition, a higher notch depth of a tube leads to a more severe unsymmetrical trend of the ovalization-curvature relationship. Focusing on the aforementioned relationships, the finite element software ANSYS was used to continue the related theoretical simulation. Furthermore, the five groups of tubes tested have different notch depths, from which five unparallel straight lines can be observed from the relationship between the controlled curvature and the number of cycles required to produce failure in the log-log scale. Finally, a failure model was proposed to simulate the aforementioned relationship. Through comparison with the experimental data, the proposed model can properly simulate the experimental data.

• Computers and Concrete
• /
• 제3권4호
• /
• pp.261-284
• /
• 2006

The flexural behaviour of symmetrically reinforced concrete (RC) columns cast of normal- and high-strength concrete under both monotonic and cyclic loading is studied based on an analytical procedure, which employs the actual stress-strain curves and takes into account the stress-path dependence of concrete and steel reinforcement. The analysis is particularly extended into the post-peak stage with large inelastic deformation at various applied axial load level. The effect of axial load on their complete flexural behaviour is then identified based on the results obtained. The axial load is found to have fairly large effect on the flexural behaviour of RC columns under both monotonic and cyclic loading. Such effects are discussed through examination of various aspects including the moment-curvature relationship, moment capacity, flexural ductility, variation of neutral axis depth and steel stress.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 가을 학술발표회 논문집
• /
• pp.475-482
• /
• 2002

A moment-curvature relationship to simulate the behavior of reinforced concrete (RC) columns under cyclic loading is introduced. Unlike previous moment4curvature models and the layered section approach, the proposed model takes into account the bond-slip effect by using a monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The pinching effect caused by axial force is considered with an assumption that the absorbing energy corresponding to any deformation level maintains constant regardless of the magnitude of applied axial lone. The advantages of the proposed model, comparing to layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures. Finally, correlation studies between analytical result and experimental studies are conducted to establish the validity of the proposed model.

• Steel and Composite Structures
• /
• 제10권3호
• /
• pp.245-260
• /
• 2010

In this paper, experimental and theoretical investigations on the response and collapse of 310 stainless steel tubes with different diameter-to-thickness ratios subjected to cyclic bending are discussed. The tube-bending device and curvature-ovalization measurement apparatus were used to conduct the experiment. The endochronic theory combined with the principle of virtual work and finite element software, ANSYS, were used to simulate the moment-curvature and ovalization-curvature relationships. It is shown that although the two methods lead to good simulation of the moment-curvature relationship, the endochronic theory combined with the principle of virtual work has the better simulation of the ovalization-curvature response when compared with experimental data and the simulation by ANSYS. In addition, the theoretical formulations proposed by Kyriakides and Shaw (1987) and Lee et al. (2001) were used to simulate the controlled curvature-number of cycles to produce buckling relationship. It is shown that the theoretical formulations effectively simulate the experimental data.

• Steel and Composite Structures
• /
• 제5권5호
• /
• pp.359-374
• /
• 2005

This paper presents the experimental and theoretical results of the viscoplastic response and collapse of 316L stainless steel tubes subjected to cyclic bending. The tube bending machine and curvature-ovalization measurement apparatus, which was designed by Pan et al. (1998), were used for conducting the cyclic curvature-controlled experiment. Three different curvature-rates were controlled to highlight the characteristic of viscoplastic response and collapse. Next, the endochronic theory and the principle of virtual work were used to simulate the viscoplastic response of 316L stainless steel tubes under cyclic bending. In addition, a proposed theoretical formulation (Lee and Pan 2001) was used to simulate the relationship between the controlled cyclic curvature and the number of cycles to produce buckling under cyclic bending at different curvature-rates (viscoplastic collapse). It has been shown that the theoretical simulations of the response and collapse correlate well with the experimental data.

• 한국전산구조공학회논문집
• /
• 제13권2호
• /
• pp.245-256
• /
• 2000

이 논문에서는 반복하중을 받는 철근콘크리트 보의 거동을 모사하기 위한 모멘트-곡률 관계를 제안하고 있다. 기존의 제안된 모멘트-곡률 관계 모델이나 적층단면법과는 달리 제안된 모델은 부착-슬립관계와 상응하는 평형방정식을 기초로 하여 구성된 단조증가 하중에 대한 모멘트-곡률 관계를 이용하여 부착-슬립에 따른 영향을 고려하고 있다. 또한 대변형 해석시 보다 개선된 결과를 얻기 위해 철근의 응력-변형률 관계에 착안한 곡선화 된 천이곡선을 사용하고 있다. 응력-변형률 관계에 기초하여 단면을 가상의 층상구조로 모사하는 적층단면법과 비교하여 제안된 모델은 단면의 거동을 모멘트-곡률 관계로 표현하는 관계로 대형구조물의 해석시 계산시간과 저장공간을 줄일 수 있는 잇점을 가지고 있다. 나아가 고정단회전과 pinching효과를 고려하기 위한 제안된 기본모델의 수정방안이 소개되고 있다. 마지막으로 제안된 모델식의 타당성을 검증하기 위하여 해석결과와 실험값들의 비교가 이루어졌다. 본 논문은 구조물의 미시적 측면에서 유효평균탄성계수를 결정하기 위한 균질화기법인 점근적 방법을 적용하였고, 탄성값을 조사하기 위하여 유한요소법으로 정식화하였다. 수치 예로서 물성치가 각기 다른 등방성 재료를 적층한 부재의 임의 단면에서 단위요소를 해석영역으로 설정하고 산출된 탄성계수를 기존의 해석방법으로부터 산출된 값과 비교하였다. 균질화기법으로 산출된 탄성계수는 과소평가되어 나타나며, 이는 해석영역을 유한요소정식화하는 과정에서 수정항만큼 차이가 난다는 것을 증명하였다. 기존 해석방법으로는 복합재료의 탄성계수가 단순히 재료의 산술적 평균값으로 계산되는 것과는 달리, 미시적으로 복합재 단위요소의 반복성을 고려함으로써 제안된 해석방법이 보다 유용하다는 것을 보여 주었다.