• Geomechanics and Engineering
• /
• 제16권2호
• /
• pp.113-124
• /
• 2018

Under repeated loading, the residual stresses within the subgrade and subsoil can accelerate the deformation of the road structures. In this paper, a series of laboratory cyclic loading model tests and small-scale model tests were conducted to investigate the dynamic stress response within soils under different loading conditions. The experimental results showed that a dynamic stress accumulation effect occurred if the soil showed cumulative deformation: (1) the residual stress increased and accumulated with an increasing number of loading cycles, and (2) the residual stress was superimposed on the stress response of the subsequent loading cycles, inducing a greater peak stress response. There are two conditions that must be met for the dynamic stress accumulation effect to occur. A threshold state exists only if the external load exceeds the cyclic threshold stress. Then, the stress accumulation effect occurs. A higher loading frequency results in a higher rate of increase for the residual stress. In addition to the superposition of the increasing residual stress, soil densification might contribute to the increasing peak stress during cyclic loading. An increase in soil stiffness and a decrease in dissipative energy induce a greater stress transmission within the material.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.239-246
• /
• 2000

It has been generally much fine contents in West Coast of Korea. When cyclic shear stress causing liquefaction was estimated as using cyclic triaxial tests in these grounds, it didn't appear linear relations between deviator stress and confining stress where σ'₃ was more than 150 kpa. Namely, due to no normalization of cyclic shear stress ratio, the errors of this is increased. Therefore, more confining stress is increased, more increment of deviator stress is decreased. So, using linear relations between tanø'/sub d/ of dynamic internal friction angle and CSR where σ'₃ was less than 150 kpa, liquefaction of these grounds was evaluated. Also, as doing detail evaluation which had carried response analysis of earthquake, this appeared good results which was well compatible with empirical methods using N-value of SPT. It was thought that these result evaluated vulnerable liquefaction area more correct than existing methods. Also, characteristics of liquefaction in West Coast grounds was compared with clean sands, with analysis of behavior of pore pressure ratio and axial strain affected by fine contents, as cyclic loading was applied.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.315-322
• /
• 2003

Cyclic simple shear tests were performed to find out the effect of preshear on dynamic strength of the sandy soil. Tests were performed for the specimens with 40% and 60% of relative density, under three different effective vertical stress of 50, 100 and 200kPa. For 50 and 100kPa, preshear ratios 0.00, 0.08, 0.12 and 0.16 were given, respectively, For low and high relative densities, two different results are shown in dynamic tests. Under the dense conditions, the maximum shear stress ratio($\tau$$\_$cyc//$\sigma$$\_$vo/) and the cyclic shear stress ratio($\tau$$\_$cyc//$\sigma$$\_$vo/) causing a certain shear strain increase with augmenting preshear ratio(${\alpha}$). However, the maximum shear stress ratio and the cyclic shear stress ratio increase or decrease with increasing preshear ratio under the loose conditions. Correction factor(K$\_$${\alpha}$/) for preshear increases at an early stage and then decreases with increasing preshear ratio at loose condition and increase with increasing preshear ratio at dense condition. Correction factor (K$\_$${\alpha}$,Max/) for preshear increases with the increasing preshear ratio irrespective of relative density, and the value of has same behavior as K$\_$${\alpha}$/.

• Structural Engineering and Mechanics
• /
• 제55권5호
• /
• pp.913-929
• /
• 2015

The ratcheting and strain cyclic behaviour of joined conical-cylindrical shells under uniaxial strain controlled, uniaxial and multiaxial stress controlled cyclic loading are investigated in the paper. The elasto-plastic deformation of the structure is simulated using Chaboche non-linear kinematic hardening model in finite element package ANSYS 13.0. The stress-strain response near the joint of conical and cylindrical shell portions is discussed in detail. The effects of strain amplitude, mean stress, stress amplitude and temperature on ratcheting are investigated. Under strain symmetric cycling, the stress amplitude increases with the increase in imposed strain amplitude. Under imposed uniaxial/multiaxial stress cycling, ratcheting strain increases with the increasing mean/amplitude values of stress and temperature. The abrupt change in geometry at the joint results in local plastic deformation inducing large strain variations in the vicinity of the joint. The forcing frequency corresponding to peak axial ratcheting strain amplitude is significantly smaller than the frequency of first linear elastic axial vibration mode. The strains predicted from quasi static analysis are significantly smaller as compared to the peak strains from dynamic analysis.

• Geomechanics and Engineering
• /
• 제7권3호
• /
• pp.297-316
• /
• 2014

This paper presents a detailed study focused on investigating the effects of silt content on the static and dynamic properties of sand-silt mixtures. Specimens with a low-plastic silt content of 0, 15, 30 and 50% by weight were tested in static triaxial, cyclic triaxial, and resonant columns in addition to consolidation tests to determine such parameters as compression index, internal friction angle, cohesion, cyclic stress ratio, maximum shear modulus, normalized shear modulus and damping ratio. The test procedures were performed on specimens of three cases: constant void ratio index, e = 0.582; same peak deviator stress of 290 kPa; and constant relative density, $D_r$ = 30%. The test results obtained for both the constant-void-ratio-index and constant-relative-density specimens showed that as silt content increased, the internal friction angle, cyclic stress ratio and maximum shear modulus decreased, but cohesion increased. In testing of the same deviator stress specimens, both cohesion and internal friction angle were insignificantly altered with the increase in silt content. In addition, as silt content increased, the maximum shear modulus increased. The cyclic stress ratio first decreased as silt content increased to reach the threshold silt content and increased thereafter with further increases in silt content. Furthermore, the damping ratio was investigated based on different silt contents in three types of specimens.

• Geomechanics and Engineering
• /
• 제31권1호
• /
• pp.87-97
• /
• 2022

The excessive settlement and deformation of disintegrated carbonaceous mudstone (DCM) embankments under dynamic loading have long been problems for engineers and technicians. In this work, the characteristics and mechanism of the plastic deformation of DCM under different degrees of compaction, water contents and confining pressures were studied by static triaxial, dynamic triaxial and scanning electron microscopy testing. The research results show that the axial stress increases with increasing confining pressure and degree of compaction and decreases with increasing water content when DCM failure. The axial strain at failure of the DCM decreases with increasing confining pressure and degree of compaction and increases with increasing water content. Under cyclic dynamic stress, the change in the axial stress level of the DCM can be divided into four stages: the stable stage, transition stage, safety reserve stage and unstable stage, respectively. The effects of compaction, water content and confining pressure on the critical axial stress level which means shakedown of the DCM are similar. However, an increase in confining pressure reduces the effects of compaction and water content on the critical axial stress level. The main deformation of DCM is fatigue cracking. Based on the allowable critical axial stress, a method for embankment deformation control was proposed. This method can determine the degree of compaction and fill range of the embankment fill material according to the equilibrium moisture content of the DCM embankment.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5654-5663
• /
• 2015

부(-)의 간극수압으로서 불포화토 내에 작용하는 석션은 입자간 응력을 증가시키며, 이에 따라 토립자 골격의 항복응력 및 소성전단강성을 증대시키는 등, 불포화토의 역학적 특성에 지대한 영향을 미친다. 따라서, 본 연구에서는 이러한 석션의 효과를 지진 등의 동적 하중조건에서 고려하기 위하여 불포화토에 대해 확장된 반복탄소성구성식에 근거한 응력-변형율 관계를 제 1 항복함수 및 제 2 항복함수를 고려하여 유도하였다. 본 관계를 2차원 및 3차원 수치해석에서 액상화 이후의 압밀거동 예측 등에 적용하는 경우에는 평균골격응력(Mean skeleton stress)의 변화를 반영하는 제 2 항복함수의 도입이 필요하나, 요소시뮬레이션에서는 제 1 항복함수만으로도 수치해석을 위한 각 물성치 및 석션 파라미터 결정이 가능할 것으로 사료된다. 본 관계와 응력반전을 반영한 반복재하 루틴을 함께 코딩(Coding)할 경우 불포화조건 하에서의 반복삼축압축시험에 대한 수치해석적 모사가 가능할 것으로 보이며, 본 연구결과는 동적 하중이 작용하는 불포화토 거동 예측의 정확도 제고에 기여할 것으로 전망된다.

• 한국지반공학회지:지반
• /
• 제6권3호
• /
• pp.41-52
• /
• 1990

To investigate the liquefaction potential of sands, a series of untrained cyclic triaxial compression tests is carried out on the samples of Ottawa, Joomoonjin, Hn river and Hongseung sands. The constitutive equations of sands are derived to explain the mechanical behavior of sands under cyclic stresses, and are applicable to liquefaction analysis. The following results are obtainded in this study. 1. Sands with the lower confining pressure or relative density are to be easily liquefied, and when the amplitude of cyclic stress are large, liquefaction takes places over only a few cycles. 2. Stress ratio, porewater pressure ratio and cyclic shear strains are to be good criteria to evaluate liquefaction potential of sands. 3. Hongseung sands which contains some silty clay shows higher dynamic properties than other sands. 4. The dynamic behaviors of undisturbed Hongseung sand are about same as those of dense sands. It is noted that undisturbed Hongseung sand shows higher liquefaction potential than the samples made by pluviation under same relative density, 5. The constitutive equations of soils under cyclic loads are developed based on the theory of elasto-plasticity, logarithmic stress-strain rela'tionship, non-associated flow rule and the concept of the boundary surface. The derived equations is applicable to predict the behavior of sands under cyclic loads and liquefaction potential with a higher accuracy. 6. Based on results of the study it may be concluded that cracks of the foundations and dislocation of the structures at Hongseung earthquakes(Oct. 7, 1978, Richter scald 5.2) are not brought by the liquefaction process.

• 대한토목학회논문집
• /
• 제26권3A호
• /
• pp.465-471
• /
• 2006

지진과 같은 동적 반복하중을 받는 강구조물의 이력거동을 구현하기 위해서는 사용된 강재의 정 동적 상태에서의 응력-변형률 관계 및 특성을 고려한 동적반복소성모델이 필요하다. 본 연구에서는 SM490강재의 정 동적 단조 및 반복하중 실험을 수행하여 역학적 특성 및 응력-변형률 관계를 명확히 하였다. 그리고 실험결과에 기초하여 SM490강재의 동적반복소성모델을 제안하였으며 이를 유한변위이론에 기초한 3차원 탄소성 유한요소해석에 적용하였다. 실험시편을 모델링하여 정 동적 단조, 반복 및 변형률속도변화에 따른 3차원 탄소성 유한요소해석을 수행하였으며 이를 실험결과와 비교하였다. 비교를 통하여 본 연구에서 개발한 해석기법이 강부재의 정 동적 변형상태를 정도있게 예측할 수 있음을 검증하였다.

• 한국지반환경공학회 논문집
• /
• 제16권10호
• /
• pp.5-14
• /
• 2015

불포화토에는 부(-)의 압력인 석션(Suction)이 작용한다. 석션은 입자간 응력을 증가시키며, 이에 따라 토립자 골격의 항복응력 및 소성전단강성을 증대시킨다. 따라서 본 연구에서는 이러한 석션의 효과를 지진 등의 동적 하중조건에서 고려하기 위해 불포화토에 대하여 확장된 반복탄소성구성식으로부터 제1 항복함수 및 제2 항복함수를 고려하여 유도된 응력-변형률 관계를 이용하여 반복삼축시험의 요소 시뮬레이션을 수행하였다. 그 결과 응력경로, 응력-변형률 관계 및 체적변형률-축변형률 관계로부터 요소 시뮬레이션은 반복삼축거동을 양호하게 모사함을 확인하였다. 본 연구결과는 동적 하중이 작용하는 불포화토 거동 예측의 정확도 제고에 기여할 것으로 전망된다.