• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.6
• /
• pp.26-32
• /
• 2019

Ball end mills used for high-speed and high-precision machining require longer machining time than flat end mills or face cutters, since the tool diameter is limited and the rigidity is reduced by the characteristics of the tool's cutting edge: at the top end of the tool, the cutting speed approaches zero and hardly removes any material. Because there is little material removal at the top end of the ball end mill, the outer cutting edge performs the majority of the work; this irregular cutting force deforms the tool and shortens its life. In this study, we attached an eddy-current sensor to a tool to measure the deformation from the cutting force and we used a tool dynamometer to measure the cutting force. We found that the change in cutting force is dependent on the change in feed rate during square-shaped processing and, as the feed rate is accelerated, the cutting force also increases. Higher cutting forces increase tool deformation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.3-6
• /
• 2002

This paper presents the cutting simulation system for prediction and regulation of cutting force in CNC machining. The cutting simulation system includes geometric model, cutting force model, and off-line fred rate scheduling model. ME Z-map(Moving Edge node Z-map) is constructed for cutting configuration calculation. The cutting force models using cutting-condition-independent coefficients are developed for flat-end milling and ball-end milling. The off-line feed rate scheduling model is derived from the developed cutting force model. The scheduled feed rates are automatically added to a given set of NC code, which regulates the maximum resultant cutting force to the reference force preset by an operator. The cutting simulation system can be used as an effective tool for improvement of productivity in CNC machining.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.97-103
• /
• 2001

The study on the high-speed machine tool is very important for the improvement of productivity since it can shortens cutting and non-cutting time. Especially, high speed of feed drive system is the major research field. In the industries of the advanced countries, the feed drive systems at the speed of 60 m/min have been already developed based on the high lead ball screws. In this study, a high speed feed drive system at the speed of 60 m/ min has been developed, and its movements characteris-tics are investigated. As the movement characteristics, positioning accuracy, angular accuracy, straightness and micro step-response are measured. Thermal characteristics of the system is also discussed. For measuring the movement characteris-tics, a laser interferometer, a memory-based Hi-coder and a cooling device are used. The experimental results confirm that the movement characteristics and the thermal behavior of the system are satisfactory in the aspect of accuracy and stability.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1669-1680
• /
• 1992

This paper deals with the prediction of cutting force and tool deflection and it's application in the flexible ball end milling process. Machining accuracy is determined by the static stiffness of tool system and the instantaneous cutting force. The static stiffness of tool system consists of the stiffness of holer and the stiffness of ball end mill. The stiffness of holder was obtained from the experimental result, and the stiffness of ball end mill with two flutes was theoretically analyzed by the finite elements method. In cutting process, the instantaneous cutting force is dependent upon the instantaneous feed and pick feed(radial depth of cut) which are varied by tool deflection. For the calculation of cutting force and deflection of ball end mill, iteration method is used with the linear interpolation to the data of cutting force obtained from rigid ball end mill and the data of tool deflection. In this paper, a for enhancing accuracy is discussed. And the selection of helix angle for minimizing machining error is also discussed.

• Journal of Power System Engineering
• /
• v.5 no.3
• /
• pp.73-79
• /
• 2001

The purpose of this investigation is experimentally to clarify the machinability and tool wear of STS 304 steel pipe material for piping. In order to determine the effects of cutting parameters and tool wear on thrust, torque, AE RMS, drilling is conducted on CNC milling machine. In this experiment, it is measured that thrust, torque, tool wear length, tool wear area and AE RMS during drilling using Hss tool. It has been found that a) During the drilling, the thrust and the torque of the STS 304 pipe are received more the effect of the feed than the spindle speed and the thrust increase with the increase of feed, b) The value of the AE RMS is been larger the effect of the cutting speed than the feed rate, and the value of the AE RMS increase with the increase of spindle speed, c) It has been found that the suitable feed in feed condition of 0.03, 0.05, 0.1, 0.15mm/rev is below 0.05mm/rev, d) The value of the AE RMS was shown a characteristic of the jump value during it was a sudden inrcrease of the tool wear. The increased character of the AE RMS value can be known an effective factor of the tool wear detection, and e) It can be quantitatively evaluated the condition of the tool according to calculate a area of the drill wear image which is obtained by a vision system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.89-95
• /
• 2019

In this research, the effect of roughing on tool load through bottom-up machining is investigated through actual machining. Generally, through the use of high-speed machining technology, machining methods, such as general roughing, operate by deepening the cutting depth for as long as the tool is able to withstand it, giving a slower feed rate, less cutting depth, and faster feed. However, when the cutting depth is deep, there is a problem in that the stepped shape of the cutting area is increased (e.g., by the shaking of the tool or the chipping load). However, if the cutting is performed less, the cutting time becomes relatively long. To compensate for these drawbacks and extend the service life of the tool, economic efficiency needs to be secured.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.133-145
• /
• 1996

This paper presents an indirect cutting force measuring system, which uses the current signals from the AC servo drive units of the horizontal machining center, with its applications to the adaptive regulation of the cutting forces in various milling processes and to the on-line monitoring of tool breakage. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that the indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The whole scheme has been embedded in the commercial machining center and a series of cutting experiments on the face cutting processes are performed. The adaptive controller reveals reliable cutting force regulating capability against the various cutting conditions. It is also shown that the tool breakage in milling can be detected within one spindle revolution by adaptively filtering the current signals. The effect of the cutter run-out has been considered for the reliable on-line detection of tool breakage.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.14-18
• /
• 2001

Rise in cutting force causes tool damage and worsens product quality resulting in machining accuracy deterioration. Especially, fragile material cutting brings about breakage of material and worsens product surface quality. In this study, we trace the locus of cutting force and examine the machined surface corresponding to the cutting force loci. and build up a monitoring system for deciding normal operation or not of cutting process.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.16-21
• /
• 2005

The cutting characteristics of hardened steel(AISI 52100) by PCBN tools is investigated with respect to cutting force, workpiece surface roughness and tool flank wear by the vision system. Hard Owning is carried out with various cutting conditions; spindle rotational speed, depth of cut and feed rate. Backpropagation neural networks(BPNs) are used for detection of tool wear. The input vectors of neural network comprise of spindle rotational speed, feed rates, vision flank wear, and thrust force signals. The output is the tool wear state which is either usable or failure. The detection of the abnormal states using BPNs achieves $96.8\%$ reliability even when the spindle rotational speed and feedrate are changed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.1038-1043
• /
• 1997

To adapt the neural network proess for the purpose of determination of optimal utting onditions (optimal cutting speed and feed rate), some selection strategies for the machining factors are necessary, which is considered planning cutting process. In this case, factors that have both nonlinearity and strong relationship must be selected. Although tool grade and chemical properties of workpiece material have strong effect to cutting speed, it's not easy to find a analytic relation between them. In this paper, a mathematical method for determining the optimal amount of cutting (depth of cut, feed rate) is presented by tool goemetry and heat generation during cutting process. And various tool grade and workpiece material groups ase classified based on its chemical properties. Thier chemical composition and hardness are used as input pattern for neural network learnig. The result of learning shows the relationship between tool grade and workpiece material and it is proved that it can be used as a sub-system for automatic process planning system.