• Journal of Bio-Environment Control
• /
• v.6 no.4
• /
• pp.277-283
• /
• 1997

The effect of nutrient concentration and plant growth regulators on rooting of Coleus stem cuttings were investigated. In contrast to sand cutting, the nutrient solution or plant growth regulator treatment increased the root numbers and root length. The concentration of nutrient solution were 1, l/2 and 1/4 strength of the balanced nutrient solution developed by Japanese Horticultural Experimental Station and the highest root growth was obtained from 1/4 strength nutrient concentration. NAA or IBA treatment in culture solution stimulated the rooting and 0.01mg/l of NAA or IBA was effective in root development. Furthermore, days for rooting were shortened and root growth were promoted by mixing nutrient solutions with plant growth regulators and by using cutting with leaves. The rooting of Coleus was observed under microscope and the adventitious root formation initiated at 3 days after cutting with nutrient and auxin mixture.

• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.451-460
• /
• 2004

The strength of sliding plane is usually assigned on the whole sliding plane with same value in 2D limit equilibrium slope stability method. However, the potential sliding plane is divided into two or three parts which have different sliding resistances. According to the calculation results of 3D slope stability analyses using 4 types of slope cutting models, marginal sliding resistance could affect the safety of slope significantly. In this calculation two kinds of the sliding plane strengths were applied differently to the parts of bottom and margin of the model slope. The effect of marginal resistance was calculated quantitatively. In case of lower sliding resistance of the bottom, the safety factor becomes low in a margin cutting model. However, in case of higher sliding resistance of the bottom, the safety factor decreased slightly in a lower part cutting model and increased in a upper margin cutting model.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.40 no.3
• /
• pp.23-38
• /
• 2015

In this paper, we evaluate the strength of three families of cutting planes for a lot-sizing problem. Lot-sizing problem is very basic MIP model for production planning and many strong valid inequalities have been developed for a variety of relaxations in the literature. To use three families of cutting planes in Branch-and-Cut framework, we develop separation algorithms for each cut and implement them in CPLEX. Then, we perform computational study to compare the effectiveness of three cuts for randomly generated instances of the lot-sizing problem.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.4
• /
• pp.117-122
• /
• 1998

Glass fiber epoxy composite material is widely used in the structures of aircrafts, robots and other machines because of their high specific strength, high specific stiffness and high damping. In order for the composite materials to be used in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joint must be provided, which require precise machining. In this paper, the machinability of the glass fiber epoxy composite material was experimentally investigated. The results can be summarized as follows : 1. The entrance of hole is very good manufacturing existing, but exit come to occur sever surface exfoliation. 2. The cutting force in drilling of the glass fiber epoxy composite material is decreased as the drilling speed increased. 3. If the glass fiber epoxy composite material is drilling by the standard twist drill, then the hole recommand cutting condition is spindle speed 400∼600rpm, feed 40∼50mm/min.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.36-43
• /
• 2003

In machining of ceramic materials, they are very difficult-to cut materials because of there high strength and hardness. Machining of ceramics are characterized by cracking and brittle fracture. Generally, ceramics are machined using conventional method such as finding and polishing. However these processes are generally costly and have low MRR(material removal rate). This paper focuses on determining the optimal levels of process parameters for products with CNC machining center. For this purpose, the optimization of cutting parameters is performed based on experimental design method. A design and analysis of experiments is conducted to study the effects of these parameters on the surface roughness by using the S/N ratio, analysis of ANOVA and F-test. Cutting parameters, namely, cutting speed, feed and depth of cut are optimized with consideration of the surface roughness.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.71-76
• /
• 2020

Various machining methods are being studied to improve the processing quality of the spherical R shape in press die. In this paper, we confirmed that changes in machining quality were associated with changes in cutting direction, path, and cutting angle, which are commonly used in the machining of molds. We obtained a surface roughness graph with each condition change in one specimen using an instrument that measured geometry and surface roughness simultaneously. The results of the study showed that the best surface roughness in the finish cut of the spherical surface was obtained using upward pick feed machining.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.926-931
• /
• 2012

Rotary bar was cutting tool being in use for deburring scale after welding metal and for eliminating sharp edges. It was necessary to develop exclusive 6-axis machine being possible to process machining continuously for making an cutting edge of rotary bar and to revise easily machining program. This study aimed at the structural analysis of strength according to the configuration of new made 6-axis machine and at the machining accuracy and durability of rotary bar. As a result of test, the runout of new rotary bar manufactured out of 6-axis machine was decreased from 0.385 mm to 0.027mm extensively than old one. And good cutting ability and durability was obtained equal quality compared with imported products.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.48-55
• /
• 1996

The aim of the present study is to investigate the scaling and dynamic erects on the plate cutting response. A series of cutting tests for unstiffened and longitudinally stiffened steel plate specimens in a quasi-static condition were carried out, varying the plate thickness. Based on the previous as well as the present test results, the scaling effect of Plate thickness on the cutting response is investigated. Dynamic erects are also clarified from the devious theoretical and experimental results. The Cowper-Symonds constitutive equation originally derived for mild steel is modified to consider the influence of strain-rate sensitivity on yield strength of high tensile steel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2279-2286
• /
• 1992

A hypereutectic Aluminum-Silicon Alloy is widely used in the parts of autombile because of high-resistance and good strength. In this study, the cutting of a hypereutectic Al-Si alloy (A390) for extraction of Si particle was experimentally investigated. By proper selection of cutting tool materials and optimization of cutting conditions, economical machining of this alloy is achieved. The surface roughness relates closely with the feed rate and cutting speed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.1-8
• /
• 2011

Recently, super heat-resistant alloy Inconel 600 come into spotlight as the material of airplane parts but this material causes lots of problems that is, reduction of machinability and attritious wear and breakage of cutting tool during turning processing due to high temperature strength and cohesion between tool material and Inconel 600. Therefore, in this study, it was purposed to determine tool material kind and to select of proper cutting range when turning process was carried out for Inconel 600. In order to these Purpose, coated carbide tool and ceramic tool was used in this experiment and the machinability of Inconel 600 was investigated from perspective of the cutting force, chipping and wear of tool and deposition phenomenon of chip.