• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1352-1355
• /
• 1996

The control of diamond turning is usually achieved through a laser-interferometer feedback of slide position. If the tool post is rigid and the material removal process is relatively static, then such a non-collocated position feedback control scheme may surface. However, as the accuracy requirement gets tighter and desired surface contours become more complex, the need for a direct tool-tip sensing becomes inevitable. The physical constraints of the machining process prohibit any reasonable implementation of a tool-tip motion measurement. It is proposed that the measured force normal to the face of the workpiece can be filtered through an appropriate admittance transfer function to result in the estimated depth of cut. This can be compared to the desired depth of cut to generate the adjustment control action in addition to position feedback control. In this work, the design methodology on the admittance model-based control with a conventional controller is presented. The recursive least-squares algorithm with forgetting factor is proposed to identify the parameters and update the cutting process in real time. The normal cutting forces are measured to identify the cutting dynamics in the real diamond turning process using the precision dynamometer. Based on the parameter estimation of cutting dynamics and the admittance model-based nanodynamic control scheme, simulation results are shown.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.119-124
• /
• 2017

Machining optimization using typical computer-aided manufacturing (CAM) software mainly depends on tool paths, and it is impossible to predict the behavior of material or cutting force. In this paper, cutting force analysis simulation is performed on the Unibody Case of a mobile phone with the aim of optimizing cutting-force-based machining using the Third Wave Systems' AdventEdge Production Module. Machining time after optimization was shortened by 42% for roughing compared to pre-optimization, and actual machining time was reduced by 36.8%. For finishing, machining time was reduced by 92%, and actual machining time was reduced around 90%. A surface roughness analysis found that the post-optimization surface roughness was $1.16{\mu}m$ Ra, compared to a pre-optimization value of $1.75{\mu}m$ Ra.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.1
• /
• pp.101-107
• /
• 2011

Analytical solution of micro-scale milling process is presented in order to suggest available machining conditions. The size effect should be considered to determine cutting characteristics in micro-scale cutting. The feed per tooth is the most dominant cutting parameter related to the size effect in micro-scale milling process. In order to determine the feed per tooth at which chips can be formed, the finite element method is used. The finite element method is employed by utilizing the Johnson-Cook (JC) model as a constitutive model of work material flow stress. Machining experiments are performed to validate the simulation results by using a micro-machining stage. The validation is conducted by observing cutting force signals from a cutting tool and the conditions of the machined surface of the workpiece.

• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.358-363
• /
• 2003

Adiabatic shear bands have been observed in the serrated chip during high strain rate metal cutting process of medium carbon steel and titanium alloy The recent microscopic observations have shown that dynamic recrystallization occurs in the narrow adiabatic shear bands. However the conventional flow stress models such as the Zerilli-Armstrong model and the Johnson-Cook model, in general, do not predict the occurrence of dynamic recrystallization (DRX) in the shear bands and the thermal softening effects accompanied by DRX. In the present study, a strain hardening and thermal softening model is proposed to predict the adiabatic shear localized chip formation. The finite element analysis (FEA) with this proposed flow stress model shows that the temperature of the shear band during cutting process rises above 0.5Τ$_{m}$. The simulation shows that temperature rises to initiate dynamic recrystallization, dynamic recrystallization lowers the flow stress, and that adiabatic shear localized band and the serrated chip are formed. FEA is also used to predict and compare chip formations of two flow stress models in orthogonal metal cutting with AISI 1045. The predictions of the FEA agreed well with the experimental measurements.s.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.9
• /
• pp.1499-1507
• /
• 2003

Physical importance of cutting temperatures has long been recognized. Cutting temperatures have strongly influenced both the tool life and the metallurgical state of machined surfaces. Temperatures in drilling processes are particularly important, because chips remain in contact with the tool for a relatively long time in a hole. Tool temperatures tend to be higher in drilling processes than in other in machining processes. This paper concerns with modeling of thermal behaviors in drilling processes as well as estimation of the cutting temperature distribution based on remote temperature measurements. One- and two-dimensional estimation problems are proposed to analyze drilling temperatures. The proposed thermal models are compared with solutions of finite element methods. Observer algorithms are developed to solve inverse heat conduction problems. In order to apply the estimation of cutting temperatures, approximation methods are proposed by using the solution of the finite element method. In two-dimensional analysis, a moving heat source according to feedrate of the drilling process is regarded as a fixed heat source with respect to the drilling location. Simulation results confirm the application of the proposed methods.

• Journal of Korea Multimedia Society
• /
• v.19 no.8
• /
• pp.1337-1344
• /
• 2016

As the visual effect frequently used in movies or animations, special effects are well suited for the creation of buildings or materials' destruction and collapse scenes. With the relevant programs developing technologically, the adoption of a real-time physically based-system makes it possible to realistically express dynamic simulations. In the large scale, the visual expression of such effects of destroying is satisfying enough, but most common programs of those effects fail to maximize visual effect generated with the cutting of small materials. Besides, to perform a heavy simulation process needs high-performance hardware and programs, where high costs would become a serious issue. For this reason, this paper suggests a solution optimized for the effect of small materials-cutting. The progress of each step shows technologies which trace movement with the state of the completion of the character's motions and then cut the material in real-time, finally led to the very realistic visual effect. Besides, using vector inner calculation to follow the motions of object and to realize cutting effect, this study provides an experiment that constructs visual effect for visualization from the basis of mathematical algorithm and it would be certainly as an educational material used for further researches.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.79-80
• /
• 2008

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.554-558
• /
• 2001

In this study, a hybrid method is used to search the pseudo-optimal solution for the I-dimentional nesting problem. This method is composed of the genetic algorithm for the global search and a simple heuristic one for the local search near the pseudo optimal solution. Several simulation results show that the hybrid method gives very satisfactory results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.255-255
• /
• 2004

일반적으로 10,000 rpm 이상의 고속, 고이송 가공이 수행되는 고속가공에서 절삭력의 급격한 증가는 치명적인 결과를 초래할 수 있다. 따라서 실제 가공에 앞서 NC code에 존재하는 에러 유무를 검출하고, 주어진 절삭 조건의 적합성을 사전에 검사하는 NC 모의 가공 시스템의 중요성이 점점 강조되고 있는 실정이다. 절삭 영역의 탐색에는 일반적으로 Z-map 방식이 사용되고 있다. Z-map 방식은 자료구조의 단순성과 완결성으로 인하여 계산속돈가 라르고 오류 발생의 가능성이 상대적으로 낮기 때문에 상용 CAM 시스템은 대부분 이 방식을 기반으로 하고 있다.(중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1096-1105
• /
• 1994

A hypereutectic Aluminum-Silicon Alloy is widely used in the parts of automobile because of high-resistance and good strength. In this study, the cutting of hypereutectic A1-Si alloy for economical production was investigated by simulation. Tool life and the extraction rate of Si particles is inversely proportional to the depth of cut. When decreasing the depth of cut, the reduction of single crystal diamond tool cost and tool change time is achieved.