• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.1049-1052
• /
• 2000

In this paper, an efficient method to find cut in the MPEG stream data is proposed. For this purpose, histogram difference and pixel difference is considered as a noise signal. The signal is then filtered out by a median filter to make the frame difference larger. The frame difference obtained in this way is classified into cut frame and non-cut frame by the 2-means clustering without using any threshold value. To improve the classification ratio, a back-propagation neural network is constructed, where outputs of 2-means clustering are used as the inputs of the network. The simulation results demonstrate the performance of the proposed methods.

• Journal of the Korean Society of Safety
• /
• v.17 no.1
• /
• pp.87-93
• /
• 2002

In this thesis using FTA technique, the author proposes a new method of analysis of some accidents in construction work. Some efficient plans of safe facility investment are made out. For this study, I referred to 'The Death Accident in Construction Works', which have been published by Korea Industrial Safety Corporation from 1993 to 1999 for 6 years. I selected some of apartment constructions which have caused many deaths for the purpose of analysis in the study. I found that the concrete work using ferro-deck takes more deaths than the conventional construction. After finding this, I selected GANG FORM works using ferro-concrete which is the most widely used but causes many accidents. On the basis of the classification, I try to do some quantitative analyses by adding the death frequency and material factors. In order to draw up the most efficient investment plan, it is imperative that FT diagram be made out and that factors. In order to draw up the most efficient investment plan, it is imperative that FT diagram be made out and that minimal Cut Set be needed. It requires a great deal to labor and time to get Minimal Cut Set. The Minimal Cut Set which is formed of these process is the main factor to analyze disaster in the work. It is desirable that we add calculated percentage of accidents to these factors to these factors in value order, that is to say, from the high cost to low cost.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.227-238
• /
• 2004

This paper is results of experimental and nunerical works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand. Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Numerical analysis with the commercially available program of FLAC were performed to compare with results of centrifuge model experiment In numerical modelling. Mohr-Coulomb elasto-plastic constitutive model was used to simulaye the behavoor of Jumunjin Standard Sand and the interface element between the lining and the covered material was implemented to simulate the interaction between them. Compared results between model tests and numerical estimation with respect to displacement of the lining showed in good agreements.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.127-134
• /
• 2000

Soil nailing is in-situ ground improvement technique of reinforcing soils using passive inclusions for the purpose of slope stability. Also soil nailing, in general, was used and studied as a reinforcement technique at cut slope, but this paper presents the results of study for soil nailing application as a reinforcement technique at the banking over slided slope. In-situ pull-out tests of nails, instrumented with strain gauges, were performed to investigate the maximum pull-out load and to calculate the unit side resistance in each different layer. And the apparent average unit side resistance of this study was compared with that of other sites installed at cut slope.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1772-1775
• /
• 2003

The stiffness of multi-articulated industrial robots is very weak, because their structure is an articulated type with some links and joints. Thus it is known that cutting processes for metals are not accepted in machine shop well, but they have a lot of merits for cutting processes, for example. drilling, tapping. and engraving etc., because of the characteristics of their high degree of freedom. The temptation of cutting aluminium was carried out to investigate the feasibility and the limitations or constrains for cutting metals on them. First the mode shapes of 6-axes FANUC welding robot were taken and analysed, and next the cutting processes were practically carried out on it. The results of study were found out to show the feasibility of cutting processes at end-milling under 6mm of tool diameter. as well as to have some limitations and constrains, for examples, surface roughness and feed rate, depth of cut, cutting force etc..

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.6
• /
• pp.52-58
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Through the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding efficiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the residual stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface roughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as possible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20~25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• Korean Journal of Organic Agriculture
• /
• v.9 no.1
• /
• pp.37-49
• /
• 2001

This experiment was carried out to investigate the effects of application levels of nightsoil sludge compost(NSC) in 3 and 4 cuttings per annum on the dry matter yields and nutritive value of orchardgrass(Dactylis glomerata L.). Annual nightsoil sludge compost(NSC) were applied at levels of 0, 10, 20, 40 and 80 ton $㏊^{respectively}$ . Relative yields of each cut to annual dry matter yield were 29.9%, 46.% and 23.2% for 1st cut, 2nd cut and 3rd cut in 3 cutting system, 23.7%, 29.3%, 34.0% and 13.0% for 1st cut, 2nd cut, 3rd cut and 4th cut in 4 cutting system, respectively. Significantly higher dry matter yield of orchardgrass obtained were 8.11 ton $㏊^{-1}$ at level of 40 ton ㏊$^{-1}$ $yr^{-1}$ in 3 cutting systems, ranges of 7.50~10.71 ton $㏊^{-1}$ at level of 10~80 ton ㏊$^{-1}$ $yr^{-1}$ in 4 cutting systems than those of non application level of NSC, respectively(p〈0.05). The mean efficiency of dry matter production to application of NSC(kg DM/ton NSC) were 46 and 102 kg in 3 and 4 cutting systems, respectively. Although th contents of crude protein(CP, %) of orchardgrass were significantly higher at the application levels of 10~80 ton $㏊^{-1}$ $yr^{-1}$ -1/ by NSC than those of the application levels at the 0 ton $㏊^{-1}$ $yr^{-1}$ in 3 and 4 cutting systems(p〈0.05), the contents of neutral detergent fiber(NDF, %) and acid detergent fiber(ADF, %) were lower in NSC plots than those at the non-application plots of NSC. The contents of total digestible nutrient(TDN, %) and relative feed value(RFV) of orchardgrass were significantly increased with increase the applicaton levels of NSC(p〈0.05).

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.10 no.2
• /
• pp.102-109
• /
• 1990

This experiment was carried out to study the effect of pure mineral nitrogen fertilizing on dry matter yield of grassland and the advisable mineral nitrogen amounts in long duration under practical conditions at the "Federal Institute for Agriculture in the Alps" in Austria. The application rates were 0, 30, 60,90 and 120 kg N/ha/cut, the cutting regimes 3-, 4-, 5- and 6-cuts/year. In order to explain the nitrogen-profitability were determined that 1 kg pure mineral nitrogen have to produce 8 - 16 kg DM/kg N in dependence on cutting regimes and requiring of nitrogen efficiencies. The results were as follows: 1. With only PK-fertilizaing average dry matter yields from 4.0 to 7.6 tons per ha and year were obtained. 2. Within all applied cutting regimes 60 kg min. Nlhalgrowth have proved to be the most efficient application rate witn 13 - 24 kg DM/kg N in dependent of cutting regimes. Comapred with only PK-treatment the DM yields increased by 3.9 - 4.7 t/ ha nad year. 3. By the sigmaformed process of Input-Output curve the highest marginal yield (the "most efficient" Ndressing rate) per ha and year was calculated: 152 kg N at 3-cut regimes, 204 kg N at 4-cut regimes, 220 kg N at 5-cut regimes and 240 kg N/ha/year at 6-cut regimes. 4. With required efficiencies of 16 and 12 kg DM/kg N 240 - 300 kg N per ha and year respectively would have to be applied at 3-cut regimes; with required efficiencies of 12 and 10 kg DM/kg N at 4-cut regimes the appropriate figures ranged from 320 to 420 kg N/ha and year, at 5- and 6-cut regimes and efficiencies of 10 and 8 kg DM/kg N results of 360 - 460 kg N and 380 - 500 kg N respectively were obtained. 5. At the relatively dry location Piber the highest dressing rates were needed in order to obtain the efficiencies from 8 to 16 kg DM/kg N, about 30 - 60 kg N/ha/year more than at the relatively moist location Admont.ist location Admont.

• FLOWER RESEARCH JOURNAL
• /
• v.19 no.4
• /
• pp.197-201
• /
• 2011

This study was carried out to investigate cut flower quality bulb circumference and cultivars affecting 7 different cultivars to produce high quality cut flower lilies. To determine the effects of bulb circumference on growth and cut flower quality of 7 different cultivars, Lilium oriental hybrid 'Chilli', 'Ismael', 'Medusa', 'Mother's Choice', 'Siberia', 'Sorbonne', and 'Yelloween' were tested. After cut flower quality experiment, the highest 1st flower bud length and cut flower height were 'Medusa' and 'Mother's Choice' respectively. Most plants had over $30^{\circ}$ stem bending angle except for 'Mother's Choice', and 'Ismael'. The study shows that the bigger bulb circumference has the better 1st peduncle diameter, inflorescence length, stem diameter, number of flowers, and fresh weight. Bulb circumference affects the 1st flower bud length, cut flower height and number of flowers. Stem bending angle, however, is affected by neither bulb circumference nor cultivar. In conclusion, growth, cut flower quality and vase life were affected by the bulb circumference rather than cultivar.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.12
• /
• pp.27-35
• /
• 2009

KICT (Korea Institute of Construction and Technology) and KISTEC (Korea Infrastructure Safety and Technology Corporation) have been carrying out inventory survey on cut slopes along national roads since 2006. Unlike precision safety check, cut slope inventory survey is a simple check about cut slope's characteristics with the naked eye to collect the data base of slope maintenance. Inventory survey is classified into general status, cut slope characteristics and inspector opinions. The inventory data are analyzed to identify dangerous slopes and decide a safety ranking. In this paper, we performed a correlation analysis using SPSS (ver.15) about the 10,461 cut slope inventory data which are collected in Kangwondo and Chungcheongdo from 2006 to 2008. We calculated the correlation coefficient between cut slope inventory data and the danger score derived from the data. And we evaluated cut slope inventory data which have the more influence on the danger degree of cut slope. According to results of correlation analysis, we found that inventory data influencing cut slope danger degree are stuck and fallen rock, orientation of discontinuity and angle of upper slope. And these data are slightly different by regionally. Later on, if inventory research is finished, we will understand regional characteristics of cut slopes.