• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.171-174
• /
• 1999

The torque of SRM is developed by phase currents and inductance variation. Phase currents and inductance variation. Phase current is often the controlled variable in electrical motor drives, so it seems natural to use closed loop current controllers. However, the highly nonlinear nature of switched reluctance motors makes optimisation of closed loop current controlled difficult because of saturation effect in magnetic circuit. Therefore, torque generation region is nonlinearly varied according to phase current and rotor position. This paper describes the torque control scheme with neural network that can control varied with load torque. The torque control is simulated by PSIM.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.181-185
• /
• 2000

To get high efficiency in variable speed control of induction motor it is required that the vector control should be separated from flux components current and torque component current. In this paper the vector control is modeled by the estimation of the stator flex. Representing induction motor speed controller as a digital system with he use of he 32bit DSP improves the motor control performance The IGBT is used as the switching device and the validity of the proposed vector control is proved through voltage current wave and the characteristics of the velocity response as the drive circuit being simplified

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.441-443
• /
• 2007

In this paper, The authors design the current controller which independently control the d, q axis current transformed by the synchronously rotating d, q axis and a Space Vector Pulse Width Modulation(SVPWM) to steadily control the output DC-Link voltage against the variable load of the three phase PWM converter. Also, This study improves the high power factor, stability, and rapid response by the phase angle control using the digital Phase Locked Loop(PLL).

• 전력전자학회논문지
• /
• 제7권2호
• /
• pp.137-148
• /
• 2002

직접토크제어 기법은 벡터제어계 설계 및 운전시 요구되는 복잡한 좌표변환과 전류제어루프가 불필요하며, 빠른 토크응답을 얻을 수 있기 때문에 벡터제어 기법에 버금가는 유도전동기의 고성능 제어기법으로 인정되고 있다. 본 논문에서는 직접토크제어 기법 적용시 중요한 어려움의 하나로 지적되고 있는 저속영역에서의 자속저하 및 이로 인한 전류고조파의 증가 문제를 해결하기 위한 대책으로서 퍼지 가변 스위칭섹터 기법과 이 기법의 실시간 적용을 위한 실현방법을 제안하였다. 제안된 스위칭섹터 기법을 포함한 유도전동기 제어시스템의 실험적 성능을 고찰하기 위하여 DSP를 이용한 제어보드를 제작하였다. 시뮬레이션과 실험 결과는 제안된 퍼지 가변스위칭 섹터 기법을 도입함으로서 유도전동기 드라이브의 성능이 현저히 개선됨을 보여준다.

• Journal of Electrical Engineering and Technology
• /
• 제10권2호
• /
• pp.529-538
• /
• 2015

Due to the high efficiency and compact mechanical structure, direct drive variable speed generators are used for power conversion in wind turbines. The wind energy conversion system (WECS) considered in this paper consists of a permanent magnet synchronous generator (PMSG), uncontrolled rectifier, dc-dc boost converter controlled with maximum power point tracking (MPPT) and adaptive hysteresis controlled voltage source inverter (VSI). For high utilization of the converter's power capability and stabilizing voltage and power flow, constant DC-link voltage is essential. Step and search MPPT algorithm which senses the rectified voltage ($V_{DC}$) alone and controls the same is used to effectively maximize the output power. The adaptive hysteresis band current control is characterized by fast dynamic response and constant switching frequency. With MPPT and adaptive hysteresis band current control in VSI, the DC link voltage is maintained constant under variable wind speeds and transient grid currents respectively.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권6호
• /
• pp.336-341
• /
• 1999

In this paper a control method to compensate the fluctuation in source voltage by using reactive current is presented. When the source voltage is changed within $\pm$10[%] range, the unit power factor is carried out. Otherwise, the converter is controlled by variable power factor. By using above control, the converter input voltage is maintained constantly. And then it was certified by simulation with the ACSL and several experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.233-233
• /
• 2000

Direct torque control (DTC) scheme provides a very quick torque response without the complex field-orientation block and inner current regulation loop. DTC is known as an appropriate scheme for high power induction motet drives because it can be used at lower switching frequency. There are two major drawbacks with the application of DTC schemes : one is large current harmonics due to flux drooping in a low speed range, the other is that the inverter switching frequency is varying according to motor parameters and operating speed. Switching devices in the power electronics drives should be supported for relatively high switching frequency. In this paper, a P-type fuzzy controller to realize the variable switching sector scheme and a PID-type fuzzy switching frequency regulator are adopted. A meaningful contribution of this paper is to propose a simple realization scheme of the fuzzy switching frequency regulator. Simulation results show the effectiveness of those propositions.

• 전기의세계
• /
• 제17권1호
• /
• pp.6-10
• /
• 1968

To control of the speed of induction Motor, a variable frequency power supply is needed. But this New type induction Motor Constitute stator and Rotor with New principle, its speed can be easily and widely Controlled by changing phase of the stator, and start at low current than rating without starter. Also, its no load current is same as shart current, and speed increase in proportion to current. On this points this induction Motor for speed control is different from induction Motor using Now.

• Smart Structures and Systems
• /
• 제25권1호
• /
• pp.65-80
• /
• 2020

In order to protect a structure over its full life cycle, a novel tuned mass damper (TMD), the so-called semi-active eddy current pendulum tuned mass damper (SAEC-PTMD), which can retune its frequency and damping ratio in real-time, is proposed in this study. The structural instantaneous frequency is identified through a Hilbert-Huang transformation (HHT), and the SAEC-PTMD pendulum is adjusted through an HHT-based control algorithm. The eddy current damping parameters are discussed, and the relationship between effective damping coefficients and air gaps is fitted through a polynomial function. The semi-active eddy current damping can be adjusted in real-time by adjusting the air gap based on the linear-quadratic-Gaussian (LQG)-based control algorithm. To verify the vibration control effect of the SAEC-PTMD, an idealized linear primary structure equipped with an SAEC-PTMD excited by harmonic excitations and near-fault pulse-like earthquake excitations is proposed as one of the two case studies. Under strong earthquakes, structures may go into the nonlinear state, while the Bouc-Wen model has a wild application in simulating the hysteretic characteristic. Therefore, in the other case study, a nonlinear primary structure based on the Bouc-Wen model is proposed. An optimal passive TMD is used for comparison and the detuning effect, which results from the cumulative damage to primary structures, is considered. The maximum and root-mean-square (RMS) values of structural acceleration and displacement time history response, structural acceleration, and displacement response spectra are used as evaluation indices. Power analyses for one earthquake excitation are presented as an example to further study the energy dissipation effect of an SAECPTMD. The results indicate that an SAEC-PTMD performs better than an optimized passive TMD, both before and after damage occurs to the primary structure.

• Journal of Welding and Joining
• /
• 제28권6호
• /
• pp.76-83
• /
• 2010

The purpose of this study is to propose a method to decide near-optimal settings of the constant current fuzzy control parameters using a controlled random search. This method tries to find the near-optimal settings of the constant current fuzzy control parameters through experiments. It has an advantage of being able to carry out searches in the search domain which includes some irregular points. The method suggested in this study was used to determine the fuzzy control parameters by which the desired welding current were formed during inverter DC resistance spot welding. The output variable was the ITAE (integral of time multiplied by the absolute error). This output variable was determined according to the input variables, which are the GE, GDE, and GDU. This study described how to obtained near-optimal welding current condition over a wide search space conducting a relatively small number of experiments.