• Journal of the Korean Chemical Society
• /
• v.44 no.3
• /
• pp.212-219
• /
• 2000

An absorption spectrometry coupled with flow injection analysis has been developed and tested for the analysis of the Cr$_2O_7^{2-}$/Nn$O_4^-$ mixtures. Even though one has to inject the sample twice into the FIA system and the process of the sample treatment is required to completely destroy the Mn$O_4^-$ ion for the analysis of the Cr$_2O_7^{2-}$ ion, the new method has definite advantages over the current method. It utilizes only a single analytical wavelength (570 nm) and enables one to construct calibration curves which accurately follow the Beer's law over wide ranges of analytical concentrations of both ions ($2.0{\times}10^{-6}$M∼$8.0{\times}10^{-3}$M for Cr$_2O_7^{2-}$ ion, $2.0{\times}10^{-6}$M∼$4.0{\times}10^{-3}$M for MnO4- ion).

• The Korean Journal of Nuclear Medicine Technology
• /
• v.22 no.1
• /
• pp.80-83
• /
• 2018

Purpose Assessment of Serum Thyroglobulin (sTg) value in total thyroidectomy patients having an ablation dose of radioactive iodine indicates remaining cancer or metastasis. Especially, sTg in patients on withdrawal thyroxine or thyrogen administration for radioiodine ablation is an important indicator to determine the direction of further treatment and prognosis. Current guidelines suggest measurement of sTg is performed at 72 hours after the last injection of thyrogen. and assumes that sTg reaches maximum serum levels at that time. The purpose of this study is to evaluate the variation of sTg measured after thyrogen administration. Materials and Methods We compared with sTg performed at 24hours(D0) and 72hours(D2) after the last injection of thyrogen. We reviewed D0 and D2 from 276 patients were divided them into three groups according to ablation dose of radioactive iodine, 5mCi(A group), 30~80mCi(B group) and 100~200mCi(C group). We used T-test for comparison between D0 and D2. sTg was measured in serum using immunoradiometric assay (Tg-plus RIA; BRAHMS, Berlin, Germany). Results There is no critical variation between D0 and D2 in A group(n=100)(P=0.32), The case of increase(D2>D0) is 45, no change(D2=D0) is 23, decrease(D2D0 is 91, D2=D0 is 28, D2D0 is 19, D2=D0 is 2. The biggest increase is 143.6 ng/mL from 98.4 to 242. Conclusion There was a significant difference in the group over 30mCi. and the case of D2>D0 is 45%, 58.7%, 90.5% for each group. therefore, D2 increased as the dose of radioactive iodine increased. Furthermore, the most sTg values of D0 and D2 are variation under 2.0 ng/mL, so reproducibility as well as sensitivity of sTg will be important at values below 2ng/mL.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.1-9
• /
• 2006

Geological storage of captured $CO_2$ is a new way of reducing greenhouse gas emissions to protect the climate, but is based on the established technology associated with injection of fluids underground. The geological formations of interest for this technique include operational and depleted oil and gas fields, and deep saline aquifers. Prediction of storage performance will depend on models of the behaviour of $CO_2$ in geological formations; these need to be refined and verified, and methods of monitoring developed and proved. These needs can be met through monitored demonstration and research projects. Current commercial projects that are demonstrating $CO_2$ storage include Sleipner, Weyburn, ORC, and In Salah; research projects include West Pearl Queen, Nagaoka, and Frio. In this paper, some of the monitored injection projects are described. The reservoirs employed for storing $CO_2$, and the associated monitoring techniques, are briefly reviewed. It is argued that small-scale research projects, used to develop techniques and prove models, are complementary to the large-scale monitored injections that will establish the viability of this technique for mitigating climate change.

• Clinical and Experimental Reproductive Medicine
• /
• v.42 no.4
• /
• pp.143-148
• /
• 2015

Objective: The aim of the current study was to determine the predictive value of anti-$M{\ddot{u}}llerian$ hormone (AMH) levels for pregnancy outcomes in patients over 40 years of age who underwent in vitro fertilization or intracytoplasmic sperm injection-embryo transfer (IVF/ICSI-ET) cycles. Methods: We retrospectively analyzed the medical records of 188 women aged 40 to 44 years who underwent IVF/ICSI-fresh ET cycles due to unexplained infertility in the fertility center of CHA Gangnam Medical Center. Patients were divided into group A, with AMH levels <1.0 ng/mL (n=97), and group B, with AMH levels ${\geq}1.0ng/mL$ (n=91). We compared the clinical pregnancy rate (CPR) in the two groups and performed logistic regression analysis to identify factors that had a significant effect on the CPR. Results: The CPR was significantly lower in group A than group B (7.2% vs. 24.2%, p<0.001). In multivariate logistic regression analysis, AMH levels were the only factor that had a significant impact on the CPR (odds ratio, 1.510; 95% confidence interval, 1.172-1.947). The area under the receiver operating characteristic curve for AMH levels as a predictor of the CPR was 0.721. When the cut-off level of AMH was set at 1.90 ng/ mL, the CPR was 6.731-fold higher in the group with AMH levels ${\geq}1.90ng/mL$ than in the group with AMH levels <1.90 ng/mL (p<0.001). Conclusion: Our study showed that AMH levels were predictive of clinical pregnancy in infertility patients over 40 years of age. Further prospective studies should be conducted to validate the predictive capability of AMH levels for the outcome of clinical pregnancy.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 2002.11a
• /
• pp.69-69
• /
• 2002

Transgenic animals production tools have been valuable for research and purpose. The current methods of gene transfer, microinjection and nuclear transfer, which are widely used in transgenic animal production, but all most methods has only had limited success in production of larger species. Here, we report the possibility of a sperm-mediated gene transfer method in porcine embryos. Oocytes were collected from ovaries harvested at a local slaughterhouse were matured in 500${mu}ell$ drops of TCM-199 under mineral oil at 38.5$^{\circ}C$ in a humidified atmosphere of 5%CO2 in air. After 42-43h of in vitro maturation oocytes were denuded. for sperm injection into the cytoplasm of the porcine oocytes, sperm suspension in NIM medium are subjected extraction with TritonX-100 before mixing with a green fluorescent gene (GFP). Sperm with Tritonx-100 were prepared by adding TritonX-100 to a final volume of 0.05% in the sperm suspension and mixing by trituration for 60s before two wishes in NIM medium at 2$^{\circ}C$. A(ter wishing, sperm were mixed with TritonX-100 at $25^{\circ}C$ followed by washes at 2$^{\circ}C$. Sperm were resuspended in ice cold NIM to a final volume of 400${mu}ell$ and 2-20ng/${mu}ell$ DNA were triturated on ice for 60s. All microinjection was performed in HEPES-buffered CZB medium at room temperature within 2h. After culture in NCSU-23 for 72h, percent of porcine embryos transfected GFP gene are 20.7%(6/29) in 20ng/${mu}ell$ sperm-DNA mixed group and other groups were 3.7 %(2/54)and 4.7%(3/67). These data suggests that sperm-mediated gene transfer method should be used to the production tool of transgenic pig efficiently.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.3
• /
• pp.392-400
• /
• 2004

This research uses the $TiO_2$/UV process to verify the most suitable condition and possibility to dispose dyeing wastewater that contains pigment and a large amount of pollutants. For this, this research has enforced experiments that compare photo adsorption, photolysis, and photo catalyst oxidation reaction, and also evaluated and analyzed the change of pH and $TiO_2$ dosage, irradiation rates of ultraviolet rays and the dosage change and injection method of $H_2O_2$. According to the results of the dyeing wastewater experiment of storehouse catalyst that uses the new form of $TiO_2$, the photo catalyst oxidation reaction proved to be more effective than photo adsorption and photolysis; 35%, 21% in the case of $TCOD_{cr}$ and 39%, 28% in the case of chromaticity. Taking into consideration the reaction time, amount of photo catalyst reaction and irradiation amount of ultraviolet rays, the decomposition efficiency of pH change proved to be most effective at pH 4. On the whole, the acidity area proved to be effective in dyeing water exclusion than neutral and alkalinity areas. Having evaluated the influence of $TiO_2$ dosage, not only does the decomposition efficiency continuously improve as the $TiO_2$ dosage increases but the shielding effect does not occur also when the $TiO_2$ is at a fixed state. The influence of ultraviolet irradiation amount concluded in the result that as the ultraviolet irradiation amount increases the decomposition efficiency continually increased, but in the case of chromaticity when the irradiation amount was higher than 37.8mW/cm2 the removal efficiency is slowed remarkably. The influence of $H_2O_2$ dosage evaluation reached the results that although the decomposition efficiency increases with the increase of $H_2O_2$ dosage, when above 150mg (total dosage: 1200mg) $H_2O_2$ consumes OH radical itself and reduces the decomposition efficiency. Also in the case of the $H_2O_2$ injection method rather than injecting in the whole amount of $H_2O_2$ (1200mg) needed at the beginning all at once, injecting divided quantities of $H_2O_2$ whenever the electric current density falls below 10mgfl reduces the wases of OH radical due to an excess of $H_2O_2$ and in tum heightens the decomposition efficiency.

• Proceedings of the Korean Biophysical Society Conference
• /
• 2003.06a
• /
• pp.23-23
• /
• 2003

It has been suggested that the impairment of smooth muscle cell (SMC) function by alterations in the $Ca^{2+}$-activated $K^{+}$ ( $K_{Ca}$ ) channels accounts for the reduction in coronary reserve during left ventricular hypertrophy (LVH). However, this hypothesis has not been fully investigated. The main goal of this study was to assess whether the properties of $K_{Ca}$ channels in coronary SMCs were altered during LVH. New Zealand white rabbits (0.8-1.0 kg) and Sprague-Dawley rats (300-400 g) were randomly selected to receive either an injection of isoproterenol (300 $\mu\textrm{g}$/kg body weight) or an equal volume of 0.9％ saline (1 mL/kg body weight). The animals developed LVH 10 days after injection. In patch-clamp experiments, the unitary current amplitude and open probability for the $K_{Ca}$ channels were significantly reduced in LVH patches compared with control patches. The concentration-response curve of the $K_{Ca}$ channel to [C $a^{2+}$]$_{i}$ was shifted to the right. Inhibition of the $K_{Ca}$ channels with TEA was more pronounced in LVH cells than in the control cells. The whole-cell currents of $K_{Ca}$ channels were reduced during LVH. Western blot analysis indicated no differences in $K_{Ca}$ channel expression between the control and LVH coronary SM membranes. In contraction experiments, the effect of a high $K^{+}$concentration on the resting tension of the LVH coronary artery was greater than on that of the control. The effect of TEA on the resting tension of the LVH coronary artery was reduced as compared with the effect on the control. Our findings imply a novel mechanism for reduced coronary reserve during LVH.ing LVH.

• Clean Technology
• /
• v.28 no.4
• /
• pp.316-322
• /
• 2022

The flow pattern at the inlet of the catalyst layer in a selective catalytic reduction (SCR) system is one of the key parameters influencing the performance of the denitrification process. In the curved diffusing parts between the ammonia injection grids and the catalyst layers, guide vanes are installed to improve flow uniformity. In the present study, a numerical simulation has been performed to investigate the effect of the geometrical configuration of the guide vanes on the aerodynamic characteristics of a denitrification facility. This application has been made to the existing SCR process in a large-scaled coal-fired power plant. The flow domain to be solved covers the whole region of the flow passages from the exit of the ammonia injection gun to the exit of the catalyst layers. ANSYS-Fluent was used to calculate the three-dimensional steady viscous flow fields with the proper turbulence model fitted to the flow characteristics. The root mean square of velocity and the pressure drop inside the flow passages were chosen as the key performance parameters. Four types of guides vanes were proposed to improve the flow quality compared to the current configuration. The numerical results showed that the type 4 configuration was the most effective at improving the aerodynamic performance in terms of flow uniformity and pressure loss.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.359-365
• /
• 2006

Since the start of the KSTAR (Korea Superconducting Tokamak Advanced Research) project, Instrumentation and Control (I&C) of the Neutral Beam Test Facility (NB-TF) has been striving to answer diverse requests arising from various facets during the project's development and construction phases. Hard-wired electrical circuits have been designed, tested, fabricated, and finally installed to the relevant parts of the system. In relation to the vacuum system I&C, controlling functions for the rotary pumps, a Roots pump, two turbomolecular pumps, and four cryosorption pumps have been constructed. I&C for the ion source operation are the temperature and flow rate signal monitoring, Langmuir probe signal measurements, gradient grid current measurements, and arc detector circuit. For the huge power system to be monitored or safely operated, many temperature measurement functions have also been implemented for the beam line components like the neutralizer, bending magnet, ion dump, and calorimeter. Nearly all of the control and probe signals between the NB test stand and the control room were made to be transmitted through the optical cables. Failures of coolant flow or beam line vacuum pressure were made to be safely blocked from influencing the system by an appropriate interlock circuit that will shut down the extraction voltage application to the system or prevent damages to the vacuum components. Preliminary estimation of the beam power through the calorimetric measurement shows that 87.9% of the total power of the 60kV/18A beam with 200 seconds duration is absorbed by the calorimeter surface. Most of these I&C results would be highly appropriate for the construction of the main NBI facility for the KSTAR national fusion research project.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1121-1125
• /
• 2004

The RT(Robot Technology) has been developed as the next generation of a future technology. According to the 2002 technical report from Mitsubishi R&D center, IT(Information Technology) and RT(Robotic Technology) fusion system will grow five times larger than the current IT market at the year 2015. Moreover, a recent IEEE report predicts that most people will have a robot in the next ten years. RCP(Robotic Cellular Phone), CP(Cellular Phone) having personal robot services, will be an intermediate hi-tech personal machine between one CP a person and one robot a person generations. RCP infra consists of $RCP^{Mobility}$, $RCP^{Interaction}$, $RCP^{Integration}$ technologies. For $RCP^{Mobility}$, human-friendly motion automation and personal service with walking and arming ability are developed. $RCP^{Interaction}$ ability is achieved by modeling an emotion-generating engine and $RCP^{Integration}$ that recognizes environmental and self conditions is developed. By joining intelligent algorithms and CP communication network with the three base modules, a RCP system is constructed. Especially, the RCP interaction system is really focused in this paper. The $RCP^{interaction}$(Robotic Cellular Phone for Interaction) is to be developed as an emotional model CP as shown in figure 1. $RCP^{interaction}$ refers to the sensitivity expression and the link technology of communication of the CP. It is interface technology between human and CP through various emotional models. The interactive emotion functions are designed through differing patterns of vibrator beat frequencies and a feeling system created by a smell injection switching control. As the music influences a person, one can feel a variety of emotion from the vibrator's beats, by converting musical chord frequencies into vibrator beat frequencies. So, this paper presents the definition, the basic theory and experiment results of the RCP interaction system. We confirm a good performance of the RCP interaction system through the experiment results.