• Macromolecular Research
• /
• v.12 no.1
• /
• pp.11-21
• /
• 2004

Toughening of epoxy resins for improvement of crack resistance has been the subject of intense research interest during the last two decades. Epoxy resins are successfully toughened by blending with a suitable liquid rubber, which initially remains miscible with epoxy and undergoes a phase separation in the course of curing that leads to the formation of a two-phase microstructure, or by directly blending preformed rubbery particle. Unlike the situation for thermoplastics, physical blending is not successful for toughening epoxy resins. Recent advances in the development of various functionalized liquid rubber-based toughening agents and core-shell particles are discussed critically in this review.

• Journal of Adhesion and Interface
• /
• v.18 no.4
• /
• pp.166-170
• /
• 2017

In this study, acrylic rubber pressure sensitive adhesives was polymerized with 2-ethylhexyl acrylate, styrene, butadiene, 2-hydroxyethyl acrylate, and acrylic acid by controlling the initiator content. The initial tackiness, peel strength, holding power, and heat resistance of the PSAs were investigated by changing the content of tackifier and curing agent. The results showed that the initial tackiness and peel strength increased as the content of tackifier increased, whereas the holding power decreased. Also, the results exhibited that that the initial tackiness, peel strength, and heat resistance decreased as the content of curing agent increased, whereas the holding power and decreased.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.529-535
• /
• 2007

Calcium oxide has been used as a demolition agent in fracturing rocks and old concrete structures, etc. With the agent, demolition work can be done in safety without a noise, vibration and any other pollution, since high expansive pressure is obtained gradually by only mixing the agents with water and pouring the slurry into boreholes. But application of the non-explosive demolition agent is a time-consuming job, especially in winter. Essentially, this problem is related to the reaction rate of calcium oxide with water. This study examines the influence of additives such as cement and anhydrite on expansion pressure of calcium oxide at different curing temperatures. The expansion pressure of calcium oxide began to increase steadily with the rise of the curing temperature. When mixing calcium oxide alone with water, blown-out shot occurred. But as additives were added to calcium oxide, the reaction of calcium oxide delayed and the expansion pressure showed gradual increment. Especially, anhydrite showed a superior delaying effect than cement on the reaction of calcium oxide.

• Microbiology and Biotechnology Letters
• /
• v.10 no.4
• /
• pp.289-295
• /
• 1982

Streptomyces bobili (YS-40) isolated from soil was tested that it had drug resistance against penicillin, cephalosporin series antibiotics and other antibiotics in the previous paper. The treatment of Streptomyces bobili, (YS-40) with ethidium bromide (EtBr), acriflavine and sodium dodecyl sulfate. (SDS) resulted in the elimination of R-plasmid from the host strain. Minimum growth inhibitory concentrations (MIC) of Hg, Ag, penicillin-G, ampicillin, chloramphenicol, oxytetracycline, streptomycin and kanamycin were found to be 15, 10, > 3, 000, > 100, > 1, 000, > 100, < 5 and < 5$\mu\textrm{g}$/$m\ell$ respectively. Among the curing agents, EtBr was proved to be the most powerful compound for the elimination of R-plasmid in the strain and the elimination rate with EtBr(10$\mu\textrm{g}$/$m\ell$) was about 98%. Optimal pH to. the elimination of R-plasmid was pH 7.0 and the R-plasmid in the cells incubated for 24 hrs was proved to be eliminated most effectively. Aerial mass color, soluble pigment formation and reverse side color were reported to be often the plasmid associated characteristics of the R-plasmid bearing bacteria. But these characteristics of the uncured and cured Streptomyces bobili, (YS-40) showed no changes in the most of the pigment formation media tested in this work.

• Composites Research
• /
• v.17 no.6
• /
• pp.37-43
• /
• 2004

To determine the effect of chain length and chemical structure of linear amine curing agents on thermal and mechanical properties, a standard bifunctional linear DGEBF epoxy resin was cured with EDA and HMDA having amine group at the both ends of main chain in a stoichiometrically equivalent ratio in condition of preliminary and post cure. From this work, the effect of linear amine curing agents on the thermal and mechanical properties is significantly influenced by numbers of carbon atoms of main chain. In contrast, the results show that the DCEBF/EDA system having two carbons had higher values in the thermal stability, density, shrinkage (%), grass transition temperature, tensile modulus and strength, flexural modulus and strength than the DGEBF/HMDA system having six carbons, whereas the DGEBF/EDA cure system had relatively low values in maximum ekothermic temperature, maximum conversion of epoxide, thermal expansion coefficient than the DGEBF/HDMA cure system. These findings indicate that the packing capability (rigid property) in the EDA structure affects the thermal and mechanical properties predominantly. It shows that flexural fracture properties have a close relation to flexural modulus and strength.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.230-236
• /
• 2019

Recently, issues related to the quality of concrete have continuously resulted in surface quality problems, such as the exfoliation of concrete surfaces due to the cost reduction of cement and poor quality fine aggregate, scaling of surfaces caused by laitance, and plastic shrinkage cracks. Prompted by social issues, the application of a photo catalyst to road structures is being attempted to solve the environmental problems caused by fine dust and automobile exhaust. In this study, chemical admixtures were developed to improve the surface quality of concrete and to apply and distribute titanium dioxide in nanoscale sizes to provide basic data for the development of a photocatalyst-curing agent. As a result of the experiment, silicon and silane were reviewed as a raw material as a curing agent to develop a high performance curing agent with better film performance than conventional curing agents because they could form a film quickly on a fresh concrete surface. The distributed stability of the ultrasonic disperser showed the best performance through an outdoor test for four weeks to review the dispersion measures for the application of nanomaterials.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.38 no.1
• /
• pp.33-41
• /
• 2011

The objective of this study was to compare the shear bond strengths of five dentin adhesive systems cured with three different light curing sources. Seventy five noncarious permanent teeth were collected and stored in an 0.1% thymol solution at room temperature after extraction. The tested adhesives were: Adper Scotchbond Multi-purpose Plus Adhesive (SM) Adper Single bond 2 (SB), Clearfil SE Bond (SE), Adper Prompt L-Pop (PL), G-Bond (GB). And three light curing unit systems were used: Elipar Free light 2(LED), OptiLux 501 (Halogen), Flipo (PAC). For the shear bonding test, the labial and lingual surfaces of permanent teeth were used. To obtain a flat dentin surface, the labial and lingual surfaces of the teeth were sanded on SiO2 with number 600 grit and then divided into 15 groups of 10 surfaces each. All samples were theromocycled in water $5^{\circ}C$ and $55^{\circ}C$ for 1000 cycles. The results were as follows: 1. When cured with Freelight 2, the shear bond strength of SM was significantly higher than that of PL, GB (p<0.05), whereas no significant difference was found among those of any other bonding agents. 2. When cured with Optilux 501, the shear bond strength of SM was significantly higher than those of any other bonding agents (p<0.05), whereas no singnificant difference was found among those of andy other bonding agents. 3. When cured with Flipo, the shear bond strength of SM was significantly higher than those of SB, SE, GB (p<0.05), whereas no significant differences was found among those of any other bonding agents. 4. For comparison according to three different light cure unit system, except SB and GB, each three dentin bonding agents showed no significant difference. For SB, only Freelight 2 was significantly higher than the others, with no significant difference between Optilux 501 and Flip. For GB, Statistically significant difference was found only between Freelight and Flipo.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.133-136
• /
• 2007

This study investigates mechanical properties of the concrete using fine particle cement which is manufactured by the pulverizing process. The variable factors are 3 types of W/C such as 40, 50, and 60%, 3 types of curing temperature such as 5, 20, and $35^{\circ}C$, and 5types of the replacement of the fine particle cement such as 0, 25, 50, 75, and 100%. The unit water content, S/a and amount of the SP and AE agents to secure the slump and air content is gradually increased in accordance with amount of replacement. It can be confirmed that the delay of the setting time depending on FC content is decreased corresponding to FC content, so the effect of the acceleration to the setting time is expected. The compressive strength corresponding to FC content is proportionally increased, and the growth is confirmed about $30{\sim}40%$ at a day in 50% of FC contents. However, the increase of the strength is gradually decreased in accordance with increasing age.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.214-217
• /
• 2004

The cure kinetics of blends of epoxy(tetraglycidyl-4,4'-diaminodiphenylmethane ; TGDDM)/curing agent(diaminodiphenyl sulfone ; DDS) resin with amine terminated polyetherimide-CTBN-amine terminated polyetherimide triblock copolymer(ABA) were studied using differential scanning calorimetry under isothermal conditions to determine the reaction parameters such as activation energy and reaction constants. By increasing the amount of ABA in the blends, the final cure conversion was decreased. Lower values of the final cure conversions in the epoxy/ABA blends indicated that ABA hinders the cure reaction between the epoxy and curing agents. 1be value of the reaction order, m, for the initial autocatlytic reaction was not affected by blending ABA with epoxy resin, and the value was approximately 1.0. The value of n for the nth order component in the autocatalytic analysis was increased by increasing the amount of ABA in the blends, and the value increased from 2.0-3.4. A diffusion controlled reaction was observed as the cure conversion increased and the rate equation was successfully analyzed by incorporating the diffusion control term for the epoxy/DDS/ABA blends.

• Conservation Science in Museum
• /
• v.21
• /
• pp.29-40
• /
• 2019

An experimental study was conducted to test the applicability of natural hydraulic lime (NHL) as a reinforcing agent for the supporting layers of mural paintings in ancient tombs.Drawing upon preceding studies on mural paintings inancient tombs, samples of reinforcing agents for various conditions were prepared using NHL products, and pseudo-samples of the supporting layers of mural paintings were also produced. The samples were cured for 7, 28, and 84 days in a high-humidity condition similar to that of the mural-tomb environment. Physical properties such as dimensional stability and compressive strength were measured for each curing period.The results indicated that the NHL samples had a rapid curing speed and a low contraction ratio and are therefore suitable as reinforcing agents, whereas they showed a poor match in terms of strength compared to the supporting layer,and also low whiteness. The dimensional stability and compressive strength testsrevealedthat an NHL product mixed with a pseudo-sample of a supporting layer provided desirable conditions for reinforcing agent. The findings suggested that different conditions for curing time and strength should be considered for each supporting layer prior to applying NHL as a reinforcing agent for damaged mural paintings in ancient tombs.