• 열처리공학회지
• /
• 제8권1호
• /
• pp.53-64
• /
• 1995

A study was made to characterize the microstructures and mechanical properties of the base metal and the heat-affected zone(HAZ) in Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulated the weld HAZ. The relationship between microstructure and toughness of HAZ was studied by impact test, O. M, SEM, TEM, and DSC. The toughness requirement of military specification value was met in all test temperatures for the base metal. The decrease of HAZ toughness comparing to base plate is ascribed to the coarsed-grain and the formation of bainite. Obliquely sectioned Charpy specimens show that secondary crack propagate easily along bainite lath. Improved toughness(240J) at HAZ of $Tp_2=950^{\circ}C$ is due to the fine grain, and reasonable toughness(160~00J) in the intercritical reheated HZA is achieved by the addition of small amount of carbon which affects the formation of "M-A". Cu precipitated during ageing for increasing the strength of base metal is dissolved during single thermal cycle to $1,350^{\circ}C$ and is precipitated little on cooling and heating during subsequent weld thermal cycle. Thus, the decrease of toughness does not occur owing to the precipitation of Cu.

• Bulletin of the Korean Chemical Society
• /
• 제32권5호
• /
• pp.1613-1619
• /
• 2011

A hybrid thermosetting maleimido epoxy compound 4-(N-maleimidophenyl) glycidylether (N-MPGE) containing Co(II), Ni(II) and Cu(II) ions was prepared by curing N-MPGE and tetradentate Schiff base Co(II), Ni(II) and Cu(II) complexes. The curing polymerization reaction of N-MPGE with metal complexes as curing agents was studied. The cured samples were studied for thermal stability, chemical (acid/alkali/solvent) and water absorption resistance and homogeneity of the cured systems. The tetradentate Schiff base, 3-[(Z)-2-piperazin-1-yl-ethylimino]-1,3-dihydro indol-2-one was synthesized by the condensation of Isatin (Indole-2, 3-dione) with 1-(2-aminoethyl)piperazine (AEP). Its complexes with Co(II), Ni(II) and Cu(II) have been synthesized and characterized by microanalysis, conductivity, Uv-Visible, FT-IR, TGA and magnetic susceptibility measurements. The spectral data revealed that the ligand acts as a neutral tetradentate Schiff base and coordinating through the azomethine nitrogen, two piperazine nitrogen atoms and carbonyl oxygen.

• 대한화학회지
• /
• 제38권2호
• /
• pp.136-145
• /
• 1994

Poly(4-vinylpyridine-co-styrene)[PVPS]리간드에 monomer착물인 M(Ⅱ)(SND) 및 M(Ⅱ)(SOPD)[M: Co(Ⅱ), Ni(Ⅱ) 및 Cu(Ⅱ)]들을 반응시켜 새로운 polymer다섯자리 Schiff base착물인 M(Ⅱ)(PVPS)(SND), M(Ⅱ)(PVPS)(SOPD)들을 합성하였다. 이들 착물들의 원소분석, IR-spectra, UV-visible spectra 및 T.G.A.측정결과에 의하여 Co(Ⅱ), Ni(Ⅱ) 및 Cu(Ⅱ) 착물들은 polymer 5배위 착물로 주어짐을 알았다. 또한 0.1M TEAP-DMF용액에서 순환 전압-전류법과 시차펄스 포라로그래피에 의한 이들의 전기화학적 성질은 Co(Ⅱ)(PVPS)(SND) 및 Co(Ⅱ)(PVPS)(SOPD)는 Co(Ⅲ)/Co(Ⅱ) 와 Co(Ⅱ)/Co(Ⅰ)의 두단계의 환원과정이 비가역적으로 일어나고, Ni(Ⅱ)(PVPS)(SND) 와 Ni(Ⅱ)(PVPS)(SOPD)는 Ni(Ⅱ)/Ni(Ⅰ)의 비가역적인 일단계 환원과정으로, 그리고 Cu(Ⅱ)(PVPS)(SND)와 Cu(Ⅱ)(PVPS)(SOPD)는 Cu(Ⅱ)/Cu(Ⅰ)의 비가역적인 일단계 환원과정으로 일어남을 알았다.

• 한국분말재료학회지
• /
• 제4권4호
• /
• pp.283-290
• /
• 1997

$Ti_5Si_3$ intermetallics containing 0-6 wt% of Cu were made by reactive sintering (RS) under vacuum using elemental powder mixtures (Process 1), electro-pressure sintering (EPS) using RS'ed materials (Process2), and EPS using elemental powder mixtures (Process 3). Relatively low dense titanium silicides were gained by process 1, in which porosity decreased with increasing Cu content. For example, porosity changed from 42 to 19.4% with the increase in Cu content from 0 to 6 wt%, indicating that Cu is a useful sintering aid. The titanium silicides fabricated by Process 2 had a higher density than those by Process 1 at given composition, and porosity decreased with increasing Cu content. For example, porosity decreased from 38 to 6.8% with the change in Cu content from 0 to 6 wt%. A high dense titanium silicides were obtained by Process 3. In this Process, porosity decreased a little by Cu addition, and was almost insensitive to Cu content. Namely, about 9 or 7% of porosity was shown in 0 or 1-6 wt% Cu containing silicides, respectively. The hardeness increased by Cu addition, and was not changed markedly with Cu content for the silicides fabricated by Process 3. This tendency was considered to be resulted from porosity, hardening of grain interior by Cu addition, and softening of grain boundary by Cu-base segregates. All these results suggested that EPS using elemental powder mixtures (Process 3) is an effective processing method to achieve satisfactorily dense titanium silicides.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.55-58
• /
• 1995

The effects of Ni contents in Cu base sintered friction material were studied. The contents of Ni were increased up to 9 wt% in the Cu-Sn matrix. The microstincture and tribological behavior of the friction material were examined. Pin on disk type of constant speed friction test rig were used to measure the friction and the wear rates. The results show that Ni addition increased the friction coefficients and decreased the wear rates of the materials. Relations between microhardness of the matrix and friction properties have been discussed. In addition optimum Ni content is recommended through the analysis of wear debris.

• 소성∙가공
• /
• 제23권6호
• /
• pp.386-391
• /
• 2014

In the current study, Al-Mn-Zn alloys are strip-cast and used as the base alloy for the core of aluminum clad sheets used in automotive condenser fins. Transition elements such as Cu and Cr are added to the base core alloy in order to improve the properties of the clad sheets. The AA4343/Al-Mn-Zn-X(X: Cu, Cr)/AA4343 clad sheets are fabricated by roll bonding and further cold-rolled to a thickness of 0.08 mm. Clad sheets were intermediately annealed during cold rolling at $450^{\circ}C$ in order to obtain 40% reduction at the final thickness. Tensile strength and sag resistance of the clad sheets are improved by Cu additions to the core alloy, while corrosion resistance is also increased. Cr-additions to the clad sheets enhance sag resistance and provide low enough corrosion, although tensile strength is not improved. The effect of Cu and Cr additions on the properties of the clad sheets is elucidated by microstructural analysis.

• 대한치과기공학회지
• /
• 제27권1호
• /
• pp.57-63
• /
• 2005

Experimental Ti-13%Zr and Ti-13%Zr-5%Cu alloys were made in an argon-arc melting furnace. The grade 2 CP Ti was used to control. To investigate the surface reaction layers produced by the reaction with mold materials and the influence of the reaction layers on the hardness of castings, A phosphate bonded $SiO_2$ base investment was used as mold material, and microstructure observation and hardness test were performed. The surface reaction layers of Ti-13%Zr and Ti-13%Zr-5%Cu alloys were thinner than that of CP Ti had a clearly multiple structure. A difference of the hardness between surface and inner of the Ti-13%Zr and Ti-13%Zr-5%Cu alloys became less than that of CP Ti. From the results, it was found that the Ti-Zr-(Cu) based alloys were possible to cast with $SiO_2$ base investment without the great changes of mechanical properties of the castings.

• 대한화학회지
• /
• 제39권12호
• /
• pp.932-939
• /
• 1995

시프 염기 구리(II) 착물에 의한 과산화수소 분해속도를 측정하였다. 과산화수소와 구리(II)-시프염기 착물의 반응속도는 $Cu^{II}BSDT$ 및 $Cu^{II}BSTP$인 경우 pH에 따라 증가하였으나 $Cu^{II}BSTT$의 경우 증가하였다가 감소하였다. 이 반응의 메카니즘은 과산화수소의 시프염기 구리(II) 착물의 탈양성자를 거친 다음에 속도결정단계에서 퍼옥소 구리착물이 생성되는 반응과정과 일치한다.

• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3615-3620
• /
• 2013

Two novel copper(II) bromide complexes with pyridine containing Schiff base ligands, $Cu(pmed)Br_2$ and $Cu(pmed)Br_2$ where pmed = N'-((pyridin-2-yl)methylene)ethane-1,2-diamine (pmed) and dpmed = N,N-diethyl-N'-((pyridin-2-yl)methylene)ethane-1,2-diamine (dpmed) were synthesized and characterized using X-ray single crystal structure analysis, optical and magnetic susceptibility measurements. Crystal structural analysis of $Cu(pmed)Br_2$ showed that the copper(II) ion has a distorted square-pyramidal geometry with the trigonality index of ${\tau}=0.35$ and two intermolecular hydrogen bonds, which result in the formation of two dimensional networks in the ab plane. On the other hand, $Cu(pmed)Br_2$ displayed a near square-pyramidal geometry with the value of ${\tau}=0.06$. In both compounds, the NNN Schiff base and one Br atom occupy the basal plane, whereas the fifth apical position is occupied by the other Br atom at a greater Cu-Br apical distance. The reported complexes show $g_{\mid}$ > $g_{\perp}$ > 2.0023 with a $d_{x2-y2}$ ground state and a penta-coordinated square pyramidal geometry. Variable temperature magnetic susceptibility measurements showed that the developed copper(II) complexes follow the Curie-Weiss law, that is there are no magnetic interactions between the copper(II) ions since the Cu--Cu distance is too far for magnetic contact.

• Journal of Plant Biology
• /
• 제23권2호
• /
• pp.55-60
• /
• 1980

The quantity of heavy metals (As, Cd, Cu, Pb, Zn) contained in marine algae collected in Onsan-myon on the east coast of Korea from March to December 1978 was determined as a part of the environmental base line survey of the Onsan Industrial Base. In general, green algae have a higher Cu content than either brown or red algae, and brown algae have higher As and lower Cu contents, while red algae have a higher Zn content. Significant differences between algal species in either Cd or Pb content were however not found.