• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.229-236
• /
• 2006

Recently, the use of crushed sand produced by the crushing of stone is continuously increasing to reach an utilization rate of about 20% of the whole fine aggregates that is foreseen to grow larger in the future. However, the lack of recognition concerning quality during the production of crushed sand results in the use of crushed sand that do not satisfy the KS F 2527 standard during the manufacture of concrete. And, studies investigating the effects of such crushed sand on concrete are still neglected. Therefore, this study intends to provide data that can be exploited for concrete using crushed sand through the analysis of the effects of the grain shape of crushed sand on the quality of concrete. Results revealed problems in the workability, air entraining and durability for a value of 53% for the solid volume percentage for shape determination specified by the current KS F 2527. Analysis showed that the adjustment of the solid volume percentage for shape determination from the currently specified 53% to 55% will improve the quality of concrete using crushed sand in high strength concrete particularly.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.10-18
• /
• 2014

Mechanically fastening FRP (MF-FRP) strips using nails and anchors, has been shown to provide a more ductile behavior to the strengthened structural element than using bonded FRP. To further advance the state of the knowledge on this strengthening method, the current study examined environmental effects for six months on MF-FRP beams. Reinforced concrete beams strengthened with mechanically fastened FRP strips and subjected to sustained loads for six months were exposed to outdoor weather and constant high temperatures ($40^{\circ}C$). For comparison, the behavior of RC beam with and without sustained loads was evaluated. Results from flexural tests did not show any significant degradation or change of failure mode as a result of sustained load and of environmental effects such as high temperatures and outdoor weather over a period of six months. Failure of the beams was governed by FRP delamination followed by concrete crushing as not much load applied to the nail and anchors because of slip effects.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.3
• /
• pp.598-602
• /
• 2004

In the preparation of jam using Undaria pinnatifida sporophyll, effects of food ingredients to the jam rheology were investigated. The paste was prepared by crushing the sporophyll using chopper and homogenizer with 2.5 times water and then it was filtrated before to make a jam. The sporophyll jam was adjusted to 62$^{\circ}$Brix by heating and concentration. It was a similar to the commercial jam in the gel strength. Among the various treatments, the jam prepared with 60% (w/w) sugar, 0.75% (w/w) high methoxy (HM) pectin and 0.3% (w/w) citric acid showed best quality aspects of both texture profile analysis (TPA) and sensory evaluation. Addition of 0,08% (v/w) synthetic strawberry flavor and 0.5% (w/w) cinnamon powder to sporophyll paste gave a good masking effect for the undesirable sea mustard flavor.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.643-655
• /
• 2005

The frontal crash optimization of S-shaped closed-hat section member using the homogenization method, design of experiment (DOE) and response surface method (RSM) was studied. The optimization to effectively absorb more crash energy was studied to introduce the reinforcement design. The main focus of design was to decide the optimum size and thickness of reinforcement. In this study, the location of reinforcement was decided by homogenization method. Also, the effective size and thickness of reinforcements was studied by design of experiments and response surface method. The effects of various impact velocity for reinforcement design were researched. The high impact velocity reinforcement design showed to absorb the more crash energy than low velocities design. The effect of size and thickness of reinforcement was studied and the sensitivity of size and thickness was different according to base thickness of model. The optimum size and thickness of the reinforcement has shown a direct proportion to the thickness of base model. Also, the thicker the base model was, the effect of optimization using reinforcement was the bigger. The trend curve for effective size and thickness of reinforcement using response surface method was obtained. The predicted size and thickness of reinforcement by RSM were compared with results of DOE. The results of a specific dynamic mean crushing loads for the predicted design by RSM were shown the small difference with the predicted results by RSM and DOE. These trend curves can be used as a basic guideline to find the optimum reinforcement design for S-shaped member.

• Steel and Composite Structures
• /
• v.27 no.5
• /
• pp.537-543
• /
• 2018

Mechanical shear connectors are commonly used to transfer longitudinal shear forces across the steel-concrete interface in composite beams. Steel pipe as a new shear connector is proposed in this research and its performance to achieve composite strength is investigated. Experimental monotonic push-out tests were carried out for this connector. Then, a nonlinear finite element model of the push-out specimens is developed and verified against test results. Further, the finite element model is used to investigate the effects of pipe thickness, length and diameter on the shear strength of the connectors. The ultimate strengths of these connectors are reported and their respective failure modes are discussed. This paper comprises of the push-out tests of ten specimens on this shear connector in both the vertical and horizontal positions in different reinforced concretes. The results of experimental tests are given as load-deformation plots. It is concluded that the use of these connectors is very effective and economical in the medium shear demand range of 150-350 KN. The dominant failure modes observed were either failure of concrete block (crushing and splitting) or shear failure of pipe connector. It is shown that the horizontal pipe is not as effective as vertical pipe shear connector and is not recommended for practical use. It is shown that pipe connectors are more effective in transferring shear forces than channel and stud connectors. Moreover, based on the parametric study, a formula is presented to predict the pipe shear connectors' capacity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.839-842
• /
• 2008

The ACI 318-05 code requires the maximum amount of shear reinforcement in reinforced concrete (RC) beams to prevent possible sudden shear failure due to over reinforcement. The design equations of the maximum amount of shear reinforcement provided by the current four design codes, ACI 318-05, CSA-04, EC2-02, and JCI-99, differ substantially from one another. The ACI 318-05, CSA-04, and EC2-02 codes provide an expression for the maximum amount of shear reinforcement ratio as a function of the concrete compressive strength, but Japanese code does not take into account the influence of the concrete compressive strength. For high strength concrete, the maximum amount of shear reinforcement calculated by the EC2-02 and CSA-04 is much greater than that calculated by the ACI 318-05. This paper presents the effects of shear reinforcement ratio and compressive strength of concrete on the maximum shear reinforcement in reinforced concrete beams. Ten RC beams having various shear reinforcement ratio were tested. Although the test beams were designed to have much more amount of shear reinforcement than that required in the ACI 318-05 code, all beams failed due to web concrete crushing after the stirrups reached the yield strain.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.76-81
• /
• 2016

Recycled aggregate is a valuable resource in Korea in lack of natural aggregate. Government recognizes the importance and suggests various policies enhancing its use for higher value-added application. Most of recycled aggregate produced currently in Korea, however, is applied for low value-added uses such as embankment, reclamation, etc. Its higher valued application such as for structural concrete is very limited. Although domestic manufacturing technology of recycled aggregate is at the world level, recycled aggregate is not applied for structural concrete. Primary reasons for the limited use of the recycled aggregate include bonded mortar and cracks occurred during crushing and hence it is very difficult to predict and control the quality of recycled aggregate concrete. This research intended to grasp combined characteristics of recycled aggregate, high early strength cement, maximum temperature and time duration of steam curing and then, analyze the effects of factors. Also, it suggested the method to improve field applicability of recycled aggregate concrete.

• Structural Engineering and Mechanics
• /
• v.74 no.5
• /
• pp.657-670
• /
• 2020

Due to the high compressive and tensile strength of ultra-high performance concrete (UHPC), UHPC used in steel concrete composite structures provided thinner concrete layer compared to ordinary concrete. This leaded to the headed stud shear connectors embedded in UHPC had a low aspect ratio. In order to systematic investigate the effect of headed stud with low aspect ratio on the structural behaviors of steel UHPC composite structure s this paper firstly carried out a test program consisted of twelve push out specimens. The effects of stud height, aspect ratio and reinforcement bars in UHPC on the structural behaviors of headed studs were investigated. The push out test results shows that the increasing of stud height did not obviously influence the structural behaviors of headed studs and the aspect ratio of 2.16 was proved enough to take full advantage of the headed stud strength. Based on the test results, the equation considering the contribution of weld collar was modified to predict the shear strength of headed stud embedded in UHPC. The modified equation could accurately predict the shear strength of headed stud by comparing with the experimental results. On the basis of push out test results, bending tests consisted of three steel UHPC composite slabs were conducted to investigate the effect of shear connection degree on the structural behaviors of composite slabs. The bending test results revealed that the shear connection degree had a significantly influence on the failure modes and ultimate resistance of composite slabs and composite slab with connection degree of 96% in s hear span exhibited a ductile failure accompanied by the tensile yield of steel plate and crushing of UHPC. Finally, analytical model based on the failure mode of composite slabs was proposed to predict the ultimate resistance of steel UHPC composite slabs with different shear connection degrees at the interface.

• Journal of Biosystems Engineering
• /
• v.28 no.4
• /
• pp.351-360
• /
• 2003

This study was carried out to settle the plugging problem which occurs frequently when agricultural wettable powder is used in pest control work using the crushing and the dispersing effects caused by irradiation of ultrasonic wave. Sonication was applied to the wettable powder suspension in a beaker for 30 seconds using a 28 kHz, 200 W PZT BLT, and the image of suspension before and after sonication was observed using a microscope and a SEM. The image of tow commercial wettable powder suspensions in water observed using an optics microscope showed that the agglomerated particles were irregularly distributed over the whole observed region when stirred mechanically, while showing more uniform distribution composed of comparatively single particles in the whole observed region after sonication. Concerning the above, the projected areas of particles in the four suspensions after sonication were decreased distinctively in the observed range of the microscope and the atomization of crystals was much developed. Over the measured range of 5.6∼4,157 ${\mu}$m particle size, the overall projected area of particles was decreased to 58.3∼89.6% on the average after sonication. When the SEM images of sonicated wettable powder suspensions dissolved in water and CH$_3$OH were compared to the suspensions before sonication, such phenomena as the atomization of particles, the expansion of voids between particles, the reduction and the decrease of agglomerated particle groups, and the progress of crack developments on the surface of flake-shaped particles were observed. It seemed possible that the plugging problem that occurs frequently in pest control machine when using wettable powder would be settled by the use of sonication.

• Journal of the Korean earth science society
• /
• v.29 no.7
• /
• pp.523-530
• /
• 2008

The phase changes and variations of elemental contents in hematite medicinal mineral were investigated by a traditional processing operation including heating and quenching in vinegar. Hematite was processed at $650^{\circ}C$ and $900^{\circ}C$ through at least 5 processing cycles. Metal extraction tests in water were carried out with the processed hematite. Heating and quenching in vinegar could not change the phase of hematite. The effect of this traditional method was not clear because there were no variational trends between extracted elements and the number of processing cycles at $650^{\circ}C$ and $900^{\circ}C$. However, the traditional processing operation of heating and quenching in vinegar was very effective to change the hematite mineral towards soft and easily crushing medicinal material.