• Computers and Concrete
• /
• 제22권2호
• /
• pp.183-196
• /
• 2018

The rheological behaviour of high strength self compacting concrete (HS-SCC) studied through an experimental investigation is presented in this paper. The effect of variation in supplementary cementitious materials (SCM) $vis-{\grave{a}}-vis$ four different types of processed crushed sand as fine aggregates is studied. Apart from the ordinary Portland cement (OPC), the SCMs such as fly ash (FA), ground granulated blast furnace slag (GGBS) ultrafine slag (UFS) and micro-silica (MS) are used in different percentages keeping the mix -paste volume and flow of concrete, constant. The combinations of rheology, strength and durability are equally important for selection of mixes in respect of high-rise building constructions. These combinations are referred to as the rheo-strength and rheo-durability which is scientifically linked to performance based rating. The findings show that the fineness of the sands and types of SCM affects the rheo-strength and rheo-durability performance of HS-SCC. The high amount of fines often seen in fine aggregates contributes to the higher yield stress. Further, the mixes with processed sand is found to offer better rheology as compared to that of mixes made using unwashed crushed sand, washed plaster sand, washed fine natural sand. The micro silica and ultra-fine slag conjunction with washed crushed sand can be a good solution for high rise construction in terms of rheo-strength and rheo-durability performance.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.629-632
• /
• 2006

This study investigated the engineering properties of crushed sand, based on improvement quality technology, and washed sand concrete by conducting mock-up test, in order to verify the availability of crushed sand for full sized structure. Test results showed that fluidity, air content, supersonic waves and corrosion state of concrete using crushed sand had favorable results. In addition, it is found that compressive strength, drying shrinkage length change, hydration heat and neutralization of crushed sand concrete exhibited similar tendency, with that of washed sand concrete. The crushed concrete using developed quality improvement technology shows comparable performance to washed sand concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.17-20
• /
• 2005

This study investigates mock-up test of the concrete containing crushed sands with improved quality and following could be draws as conclusions. The slump satisfies the target value. The air content reaches the goal, however, it decreases by the occurrence of loss with elagse of age. In normal strength region, the setting time of CS24 member is shorter than that of SS24 member. In high strength region, the setting time of SS50 member is make only slower than that of CS5O because of the use of retarding AE agent. The compressive strength of the concrete using crushed sands is little higher than the concrete using washed sea sands, and the compressive strength of core sample increases at lower part. Drying shrinkage of the concrete using crushed sands is larger than that using washed sea sands. At water caring condition, both the concrete using crushed sands and using washed sands expand at first, exhibit to be swelled and with elagse of age, they remain relatirely constant. Also, the drying shrinkage occurred greatly when the width and thickness of a member are small because it is easy to evaporate the inner part vapor in the small width and thickness of a member. there can be little different according to the location of a contact gauge, however it is similar to the change of specimen's length change. The concrete using crushed sands, of which grading, grain shape and fine particle is improved, are comparable to the quality of the concrete using washed sea sand.

• 산업기술연구
• /
• 제22권A호
• /
• pp.119-125
• /
• 2002

In Kwangjin industrial company, mill is operating for the foundry sand production at the rate of 25t/hr from quartzite. Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe crushed, washed, graded, dried, and cooled clay-free sands. This study was conducted for the investigation of the foundry sand productivity and the life span of the hammer according to the material quality. The life time of hammer from several manufacturer were compared in order to find out the grinding efficiency of the various hammer material. In the result of tests, the life time of high-Mn hammer was 10.5 hours while that of high-Cr was 19.5 hours. The life time in case of typical worn shape hammers was about 12 hours and the average time of a blowhole hammer was about 6.5 hours.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.613-620
• /
• 2002

Sand Compaction Pile(SCP) is a soil improvement method that a sand charge is introduced into the pipe, and the pipe is withdrawn part away while the sand pile is compacted and its diameter is enlarged. The sand used in this method should be of good quality. In Korea, crushed stone and washed sea sand are used frequently in SCP. However, use of these materials is restricted because of environmental problem and deficiency of supply. In the copper smelting process, about 0.7 million tons of copper slag are produced in Korea. The range of particle size distribution of copper slag is from 0.15mm to 5mm, so it can be a substitute for sand, and the relatively high specific gravity compared with the sand, is its characteristic. Copper slag is hyaline and so stable environmentally that in foreign country, such as Japan, Germany etc., it is widely used in harbor, revetment and offshore structure construction works. Therefore, in this study, the several laboratory tests were peformed to evaluate the applicability of copper slag as a substitute for sand of SCP. From the mechanical property test, the characteristics of sand and copper slag were compared and analyzed, and from laboratory model test, the strength of composite ground was compared and analyzed by monitoring the stress and ground settlement of clay, SCP and copper slag compaction pile. Specially, this study focused on the application of copper slag as sand substitute in SCP pilot tests based on laboratory tests results.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3719-3725
• /
• 2012

최근, 건설공사의 급증으로 인한 양질의 하천모래의 고갈로, 콘크리트용 대체골재로서 바다모래, 부순모래 및 순환잔골재 등의 사용이 증가하고 있다. 그러나, 미세척 바다모래는 함유된 염화물로 인하여 철근콘크리트 구조물에 사용할 경우, 철근부식 유발로 구조물의 내구성에 악영향을 미치고, 부순모래는 미립분이 많고 입도조정이 어려워서 철근콘크리트 구조물에 널리 사용되지 못하고 있는 실정이다. 한편, 낙동강 세사는 낙동강 중 하류에 대규모로 분포하고 있고, 입도를 제외하면 콘크리트용 잔골재로서 품질이 우수하므로 이에 관한 연구가 시급히 요구되고 있다. 따라서 본 연구의 목적은 콘크리트 잔골재로서 낙동강 세사를 적극적으로 활용하기 위하여 그것의 물성을 평가하는 것이다. 이를 위하여 낙동강 본류 대표위치별로 시료를 채취하여 이들의 절건밀도, 입도, 단위용적질량 등의 물성을 평가하였는데, 그 결과 낙동강 세사는 입도를 제외하면 잔골재로서의 물성이 우수한 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.322-325
• /
• 2003

Recently, as quality river aggregates like sands and gravels become scarce, use of crushed stones and sands, seashore sands, and seashore gravels is increasing abruptly. And, aggregates recycled from slags and waste concretes are used. However, since the converter slag easily expands and breaks due to free lime, differently from the blast-furnace slag, it is not suitable for use as concrete aggregates. Since the atomized steel slag aggregate has slippery surface and spherical shape, the mortar flowing characteristics improved as the atomized steel slag content increases, without regard to the aggregates coarseness and water/cement ratio. The flow characteristics loss rate of the mortar manufactured from steel slag aggregates was similar to that of the mortar manufactured from washed sand only. The compact strength of the mortar manufactured from coarse PS Ball were larger than that manufactured from washing sand only.

• 한국방재학회 논문집
• /
• 제10권6호
• /
• pp.35-43
• /
• 2010

본 연구는 콘크리트 포장설계법에 사용되는 재료입력변수의 DB화를 염두에 두고 신뢰성 있는 콘크리트 물성 정량화 수립을 목적으로 수행되었다. 실험에 사용된 포장용 콘크리트는 화강암, 석회암, 사암의 조골재를 사용하였으며 화강암 배합의 경우 세 골재로서 자연사, 세척사, 부순모래 배합을 포함하였다. 먼저 콘크리트 강도시험을 통해 얻은 데이터를 이용하여 강도간의 상관관계 모델식을 정리하였다. 그리고 각 조골재별로 재령에 따른 압축강도, 휨강도, 쪼갬인장강도 및 탄성계수의 모델식을 제시하였다. 화강암 배합의 경우 세골재로서 사용된 자연사, 세척사, 부순모래 배합을 모두 포함한 산술평균을 적용하여 모델식을 제시하였다. 한편 쪼갬인장강도와 탄성계수는 실험방법 및 계측상 결과가 분산되는 경향이 있어서 상관관계식에서 예측된 값과 직접 구한 실험결과에 대해 산술평균을 적용후 보정하여 각 조골재별로 재령에 따른 탄성계수 및 쪼갬인장강도의 예측식을 제시하였다. 마지막으로 각 조골재 배합별 콘크리트의 포와송비 및 건조수축에 대한 기준 값을 제시하였다.

• 한국건축시공학회지
• /
• 제3권4호
• /
• pp.79-86
• /
• 2003

The purpose of study is to offer base data for high fluid concrete mix property, as grasp effect of aggregate to reach much more effect for producing high fluid concrete. For this study, there are three types of combined aggregates, river sand + river aggregate(type A), river sand + crusted aggregate(type B), washed sea sand + crushed aggregate(type C) and take a factor, water-contents, water-binder ratio and S/a. And so, we had following conclusion, resulting application-ability of high fluid mortar by K-slump tester to use a handy consistency measuring instrument. And so, we had following conclusion, resulting application-ability of high fluid concrete by K-slump tester to use a handy consistency measuring instrument. 1) In cafe of regular water binder ratio, high fluid concrete suffered much effect of combined aggregates and water binder ratio. Range of water binder ratio by combined aggregates is w/b 0.4 downward(type A and B), w/b 0.35 downward(type C). 2) Water contents to need for producing high fluid concrete is minimum 170kg/$\textrm{m}^3$ without regard to combined aggregates. 3) The effect of S/a on high fluid concrete by combined aggregates is approximately S/a 50% (type A and B), s/a 50-55% (type C). 4) Consistency measuring of high fluid concrete by K-slump tester is possible and first indication value, high fluid concrete can be produced, is 6~10.5cm.

• 한국도로학회논문집
• /
• 제9권4호
• /
• pp.205-213
• /
• 2007

본 연구에서는 포장용 콘크리트의 강도실험을 통해 강도간의 상관관계식을 도출하는 것을 목적으로 하였다. 강도로서 재령별 압축강도, 휨강도, 할렬인장강도와 탄성계수를 측정하였다. 배합변수는 조골재(화강암, 석회암, 사암), 세골재(자연사, 세척사, 부순모래) 및 단위시멘트량(315-375kg)을 변수로 하였다. 전체적으로 골재나 단위시멘트량보다는 재령에 의해 전형적인 강도곡선을 따라 뚜렷하게 변화함을 보여준다. 이러한 강도결과를 바탕으로 휨강도와 압축강도, 할렬인장강도와 압축강도, 탄성계수와 압축강도, 할렬인장강도와 휨강도의 상관관계를 분석한 결과 휨강도와 압축강도, 탄성계수와 압축강도는 기존의 관례대로 제곱근(n=0.5)의 상관관계식이 잘 맞음을 알 수 있었다. 할렬인장강도와 휨강도는 선형의 상관관계식으로 표현하였고, 할렬인장강도와 압축강도는 n=0.87의 지수승을 사용한 경우가 가장 적합한 것으로 나타났다.