• The korean journal of orthodontics
• /
• v.29 no.5 s.76
• /
• pp.563-573
• /
• 1999

The purpose of this study was to evaluate the availability of computer system for the measurement of tooth size in the model analysis through the comparison of two measurements: One was to use a computer; and the other was to use vernier calipers. Twenty sets of casts were used, which showed a moderate degree of crowding and full eruption of all teeth. The mesio-distal width of 12 teeth from the left central incisor to the left first molar at each set of the casts were measured twice with vernier calipers and a computer respectively. This measurement was repeated two weeks later. First, for the reproducibility analysis, the two computer measurements were compared then the vernier calipers measurements were compared. Second, all the teeth were sepapated into the region of mesiodistal contact points and its width was measured by a micrometer to obtain standard measurements. For the accuracy analysis, these standard measurements were compared with the measurements from the dental casts using two methods. The difference between them was defined as the measurement error. To investigate the cause of measurement error, an examination was made for the presence and degree of contact point deviation on each tooth from the upper and lower occlusograms, and the mesio-distal angulation of each tooth was measured with TARG. Following results were obtained through statistical analysis. 1. In the analysis for reproducibility; the measurements with vernier calipers showed significant differences in three out of twelve teeth while the computer measurements showed significant differences in one out of twelve teeth. 2. In the analysis for accuracy; compared with the standard measurements, the measurements with vernier calipers showed significant differences in three out of twelve teeth while the computer measurements showed significant differences in two out of twelve teeth. 3. Compared with the standard measurements, the measurements with vernier calipers were apt to be larger at the upper first molar, and smaller at the lower first molar The computer measurements, however, were apt to be larger at both upper and lower first molars. 4. The measurements with vernier calipers showed the largest error at the lower first molar and the degree of error was variable according to the tooth while the difference of error was small in the computer measurements. 5. In the analysis for the correlation of the degree of measurement errors with the contact point deviation index and the mesio-distal crown angulation of each tooth, the measurements with vernier calipers did not show significant correlation while the measurements with computer showed slight Positive correlations. The results of this study indicate that a computer system may be useful for the measurement of tooth size in the model analysis.

• Korean Journal of Weed Science
• /
• v.17 no.3
• /
• pp.269-280
• /
• 1997

Collated data from the 1995-1996 field surveys of weed seeds buried in the plough layer of peat soil in Selangor district were analysed to assess species-dominance and spatial pattern of distribution of weed seeds based on selected quantitative indices and index of dispersion. Forty five species within 14 families were recorded of which 24 were broadleaves, 12 grasses and 9 sedges. They comprised ca. 53.2, 31.2 and 15.6%, respectively based on total population counts. Total seed population was ca. $8.14{\times}10^7$ seeds/ha within the fast 25cm soil depth. Wide variabilities in population counts were registered among species ranging from < $7.0{\times}10^4$ seeds/ha for Amaranthus gracilis to ca. $5.64{\times}10^6$ seeds/ha for Heteropogon contortus. Seeds of Cleome rutidesperma was the most abundant(ca. $2.347{\times}10^7$ seeds/ha). Difference in seed population counts may be attributed to inherent variation in fecundity, population fluxes, their spatial distribution patterns and the agronomic practices prevailing in the areas of survey. The profile distribution of soil seed banks was skewed within the first 0 - 10cm depth, comprising ca. 69% of the total seed counts. Seed counts in the 10 - 15, 15 - 20 and 20 - 25cm soil profiles were in the order of 17.9, 8.6 and 4.0% of the total populations, respectively. Weed seeds of all species displayed different degree of aggregated pattern of distribution with variance-to-mean ratios of > 1 and Lloyd's mean crowding($m^*$) values from 1.244 for Cyperus iria, Phyllanthus debilis, Phyllanthus urinaria, Scirpus grosses and urinaria lagopodiodes to 9607.7 for Cleome rutidosperma. Lloyd's patch indices(Ip) ranging from 5.1 for Aeschynomene indica to 188.5 for Bracharia reptans were registered. Differences in the VMR, $m^*$ and Ip values among species suggested inter-alia inherent variabilities in their disposal capacity from seed source and different agronomic practices prevailing in the areas surveyed.

• The korean journal of orthodontics
• /
• v.29 no.4 s.75
• /
• pp.483-490
• /
• 1999

Interdental enamel stripping is an usual method for correction of abnormal tooth shape and tooth size discrepancy which is one of the etiologic factors of malocclusion. Clinically it Is useful to correct the minor crowding in anterior teeth and posterior occlusion during finishing stage of orthodontic treatment. But this procedure has risks such as irreversible tooth reduction and remaining roughness of enamel surface can accumulate plaque which can evoke periodontal problem. Even if various methods were introduced to minimize the enamel surface roughness, their evaluation was limited in morphologic differences by scanning electronic microscope(SEM). The purpose of this study was to compare the various interdental enamel stripping method by SEM and to quantify the difference of surface roughness by use of Surfcorder SEF-30D(Kosaka Lab. Ltd.) which can measure the roughness of surface. The stripping methods were divided into mechanical and mechanical-chemical method. Air-rotor stripping and separating strip were used for mechanical stripping and $37\%$ phosphoric acid was used for chemical stripping. The enamel surface roughness after mechanical or mechanical-chemical stripping of interproximal surfaces of premolars which were extracted for orthodontic purpose were measured and compared by means of SEM and $Surfcorder^{\circledR}$, the results were as follows. 1. Enamel surface of primary treated by coarse diamond bur and separating strip groups showed highest value of roughness. 2. To compare the primary treated groups between mechanical and mechanical-chemical method, the latter group showed lower value of roughness remarkably. 3. Mechanical stripping groups which were treated both coarse and fine instrument showed lower value of roughness as much as non treated group. 4. The use of Pumice for final polishing did not show significantly smoothening the stripped enamel surface any more.

• Korean Journal of Agricultural Science
• /
• v.20 no.2
• /
• pp.109-116
• /
• 1993

This experiment was carried out to investigate the competition in mono-and binary-associations of four forage species; ochardgrass (Dactylis glomerata L. cv. Potomac), tallfescue (Festuca arundinacea Scnreb, cv. Fawn), white clover (Trifolium repns L. cv. California), and red clover (Trifolium pratense L. cv. Kenland) as affected by different sowing rate. Each species was grown in interspecific stands in field. And samplings of shoot were taken at first cliping stages. The interspecific competition was evaluated by calculating traditional methods: aggressivity, relative yield total (RYT), relative crowding coefficient (RCC), and compensation index (CI) with shoot dry matter production and calories of nutrient ingredient of each species in mono-and binary-mixture. Compared mixture with monoculture. RYT based on dry weight was lucrative in mixture except for orchardgrass-redcover (1:0.1,1:1). RYT of calculated calories with produced nutrients was in inlucrative in mixture of orchardgrass-redclover's 1:0.1 mixture by RYT<1.0. Generally, RYT was the highest in mixture of 1:0.5 sowing rate. Aggressivity of grass was poor competition tendency that raised up legume's sowing rate, particularly, with whiteclover. In grasses, tallfescue was stronger competitor than orchardgrass with legume in mixture, RCC of grasses against legume's growth was depressed in higher sowing rate with legume. Grass's growth depression was severer with whiteclover than redclover in mixture.

• The korean journal of orthodontics
• /
• v.26 no.1 s.54
• /
• pp.17-32
• /
• 1996

It is important to understand the operating mechanism and force system of fixed appliance that most effective for individual tooth movement in various orthodontic appliances. The archwire system of fixed appliance is devided into 3 types, which is continuous arch, segmented arch and sectional arch. The last two types have longer interbracket distance and simple force operating points, so it is easy to control force system by operator. But the continuous arch has shorter interbracket distance and various bracket geometry, so it is hard to control and anaylze the force system. The purpose of this study was three dimentional force and moment analysis of continuous arch system by finite element method, which is similar situation to three dimentional elastic beam in structural engineering. Several sample form of various bracket geometry and artificial lower crowding typodont made by author were constructed, analyzed and compared each other. The results were as follows : 1. The force magnitude is linear proportional to the degree of displacement or tilting of the bracket. 2. The force magnitude is inversely non-linear proportional to the interbracket distance. 3. In three dimensional typodont model, while the force can be compared with that of the sample form in the area where adjacent bracket geometry is simple, the force is much more than the expected value in the area where adjacent bracket geometry is complex.

• The korean journal of orthodontics
• /
• v.41 no.6
• /
• pp.399-410
• /
• 2011

Objective: The purpose of this study was to evaluate the difference in frictional resistance among metal, ceramic, self-ligation brackets and coated or non-coated Ni-Ti archwires at various bracket-archwire angulations during the sliding movement of an orthodontic archwire, using an orthodontic sliding simulation device. Methods: Four types of bracket (Micro-arch Perpect Clear2 Clippy-C and Damon3 and 5 types of orthodontic archwire (0.014", 0.016", and 0.016" ${\times}$ 0.022" inch coated Ni-Ti, and 0.016" and 0.016" ${\times}$ 0.022" inch Ni-Ti) were used. Further, the bracket- archwire angles were set at 4 different angulations: $0^{\circ}$, $3^{\circ}$, $6^{\circ}$, and $9^{\circ}$. Results: The frictions from all the experimental groups were found to be significantly increased in order of self-ligation brackets, Micro-arch and Perpect Clear2 ($p$ < 0.001). The presence of a coat had no effect on the friction of the same sized archwires at $0^{\circ}$ and $3^{\circ}$ bracket-archwire angles ($p$ < 0.001). Coated archwires had significantly higher frictions than the same sized non-coated archwires at $6^{\circ}$ and $9^{\circ}$ bracket-archwire angles ($p$ < 0.001). The frictions increased significantly as the bracket-archwire angles were increased ($p$ < 0.001). Conclusions: The use of self-ligation brackets will be beneficial in clinical situations where a low frictional force is required. Further, in cases where crowding is not severe, the use of coated archwires should not cause problems. However, more additional explanation is required considering the fact that the damage of coated archwire and exposure of the metal portion in case of binding and notching and the effects of saliva were not taken into account.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.41 no.3
• /
• pp.207-217
• /
• 2014

The purpose of the present study was to evaluate the relationship between the malocclusion and dental caries in adolescents with permanent dentition. The subjects of the study were 385 adolescents aged 12 to 15 years. Dental Aesthetic Index (DAI) and DMFT index were recorded as clinical indicators of malocclusion and dental caries. The mean Dental Aesthetic Index (DAI) score of the subjects was 12.42 and the mean DMFT index of the subjects was 2.89. Four students (1.04%) were included in the group of orthodontic treatment mandatory, which signifies the handicapping malocclusion. Moreover, the result of gender-specific analysis of the DAI components observed that the prevalence of midline diastema and mandibular overjet were significantly higher among boys (p < 0.05). In 7 components (missing teeth, incisal segment crowding, maxillary anterior irregularity, mandibular anterior irregularity, mandibular overjet, anterior openbite, antero-posterior molar relationship) among the 10 DAI components, abnormal groups showed significantly higher DMFT index than normal groups (p < 0.05). The subjects in the group of definite to handicapping malocclusion (DAI ${\geq}$ 26) showed significantly higher DMFT index than the subjects in the group of minor or no malocclusion (p < 0.01). In addition, the DAI score had significant positive linear correlation with the DMFT index (r = 0.584, p < 0.01). Consequently, the current findings suggested a positive relationship between the malocclusion and caries prevalence. And several specific types of malocclusion were supposed to be significantly correlated with dental caries.

• Fire Science and Engineering
• /
• v.31 no.4
• /
• pp.95-102
• /
• 2017

The fires in the traditional markets often occur recently with the most of them expanded into great fires so that the damage is very serious. The status of traditional markets handling the distribution for ordinary people is greatly shrunk with the aggressive marketing of the local large companies and the foreign large distribution companies after the overall opening of the local distribution market. Most of the traditional markets have the history and tradition from decades to centuries and have grown steadily with the joys and sorrows of ordinary people and the development of the local economy. The fire developing to the large fire has the characteristics of the problem that the fire possibility is high since all products can be flammable due to the deterioration of facilities, the arbitrary modification of equipment, and the crowding of the goods for sale. Furthermore, most of the stores are petty with their small sizes so that the passage is narrow affecting the passage of pedestrians. Accordingly, the traditional markets are vulnerable to fire due to the initial unplanned structural problem so that the large scale fire damage occurs. The study is concerned with systematically classifying and analyzing the result by applying the TRIZ tool to the fire risk factors to extract the fundamental problem with the fire of the traditional market and make the active response. The study was done for preventing the fire on the basis of it and the expansion to the large fire in case of fire to prepare the specific measure to minimize the fire damage. On the basis of the fire expansion risk factor of the derived traditional market, the study presented the passive measures such as the improvement of the fire resisting capacity, the fire safety island, etc. and the active and institutional measures such as the obligation of the fire breaking news facilities, the application of the extra-high pressure pump system, the divided use of the electric line, etc.

• 한국사회정책
• /
• v.25 no.3
• /
• pp.37-71
• /
• 2018

Since 2016, public and political interest on basic income has been increased beyond academic interest. The recent debate on basic income has expanded on issues regarding to the concrete implementation of basic income moving further than the debate on conception of the basic income in the abstract level. This study examines major critiques of basic income which was raised from social policy area and makes a counter-argument on these critiques. Major points summarized as follows. First, the problem of jobs and social insurance exclusion is not serious enough to call for basic income. Second, existing social security systems will be crowded out by excessive financial burden if basic income is introduced. Third, policies to cultivate citizens' capacities to cope with a technological change should be given priority over basic income. This study disputes these critiques by counter arguing four points. First, it is necessary to reconstruct welfare state based on basic income, given the labor market changes, such as long-term trend of employment change, newly emerging employment of platform companies, and inconsistency of platform labor and social insurance. Second, hypothesis of crowding-out effect on social security system is just a criticism that can be applied to the basic income initiative of the right-wing. Also, it is unable to find a logical basis or evidence of this hypothesis from the historical process of welfare state development or previous studies. Third, it is necessary to discuss how to reconfigure existing social security system and basic income which are complementary to each other and also have consistency with labor market as a configuration, not as a matter of choosing between basic income and social security system. Fourth, de-laborization does not mean a refusal to labor but a free choice, and the basic principle of social security is not needs but right. In conclusion, in order to develop more productive debate on basic income, it requires more sophisticated discussion and criticism from the point of view of the distributive justice; the debate on the sustainability of social insurance-centered welfare states; and debates on the political realization of basic income.

• Economic Analysis
• /
• v.26 no.1
• /
• pp.1-33
• /
• 2020

Recent discussions about a minimum wage increase (MWI) and its influence on the economy have mainly focused on the quantitative aspects, such as labor costs and employment. However, concerning the qualitative aspects, an MWI could have positive effects by enhancing firm productivity and crowding out marginal firms from the market. These positive effects of an MWI can offset, to some extent, its potential negative effects - increasing labor costs and decreasing employment, among others. In this regard we empirically examine the impact of an MWI on firm productivity (total factor productivity). Using firm level panel data from the manufacturing industry in Korea, we calculate the influence rates of a minimum wage by sector and by firm size (number of workers), and analyze its effects on firm productivity. In particular, the production functions of the firms are estimated by taking into account endogeneity among the input factors, in order to resolve the drawbacks of existing studies - underestimating the capital factor coefficient and overestimating the labor factor coefficient. This study finds that the influences of an MWI on wages, employment, and productivity are substantially different across sectors and firm sizes. While an MWI has shown to have positive influences on productivity growth in the manufacturing industry as a whole, each sector demonstrates a different direction of effect, and the degree of productivity change also varies by sector. The impacts of an MWI on firm productivity are generally estimated to be more negative for smaller firms, but in some sectors the effects are found to be positive. In addition, the wage increases resulting from an MWI seem to cause a productivity enhancement across all sectors in the manufacturing industry. The policy implications of this study are as follows. Considering the empirical findings that an MWI causes an increase in productivity in many sectors of the manufacturing industry, it would be desirable to take into consideration not only the negative side effects but also the positive effects of an MWI when designing any future minimum wage policy. Moreover, in spite of there being a uniform minimum wage, this study finds that the diverse influence rates of a minimum wage across firms have different impacts on wages, employment, and productivity across sectors or firm size. This finding could be conducive to discussions about differentiation among minimum wage schemes by sector or firm size.