• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.2
• /
• pp.45-49
• /
• 2008

This paper investigated the accuracy of the current design formulae for the elastic buckling strength of web-tapered I-beams in AISC-LRFD specification. The basic concept is to replace a tapered beam by an equivalent prismatic beam with a different length, but with a cross section identical to that of the smaller end of the tapered beam. The modification factor, B, is used to account for the stress gradient within the unbraced length and the lateral restraining effects offered by the adjacent segments. The modification factor(B) suggested in AISC-LRFD specification was compared with the finite element method(FEM) results. This paper presented a redefined method to calculate the modification factor(B).

• Advances in concrete construction
• /
• v.11 no.4
• /
• pp.271-284
• /
• 2021

This study aims to trace the response of twelve one-way sustainable concrete hollow-core slabs made by reducing cement content and using replacement of coarse aggregate by plastic aggregate. The trial mixes comprise the 25, 50, 75, and 100% replacement of natural coarse aggregate. The compressive strength of the resulting lightweight concrete with full replacement of coarse aggregate by plastic aggregate was 28 MPa. These slabs are considered to have a reduced dead weight due to using lightweight aggregate and due to reducing cross-section through using voids. The samples are tested under two verticals line loads. Several parameters are varied in this study such as; nature of coarse aggregate (natural or recycled), slab line load location, the shape of the core, core diameter, flexural reinforcement ratio, and thickness of the slab. Strain gauges are used in the present study to measure the strain of steel in each slab. The test samples were fourteen one-way reinforced concrete slabs. The slab's dimensions are (1000 mm), (600 mm), (200 mm), (length, width, and thickness). The change in the shape of the core from circular to square and the use of (100 mm) side length led to reducing the weight by about (46%). The cracking and ultimate strength is reduced by about (5%-6%) respectively. With similar values of deflection. The mode of failure will remain flexural. It is recognized that when the thickness of the slab changed from (200 mm to 175 mm) the result shows a reduction in cracking and ultimate strength by about (6% and 7%) respectively.

• Steel and Composite Structures
• /
• v.41 no.6
• /
• pp.787-803
• /
• 2021

The size-dependent nonlinear thermomechanical vibration analysis of pre- and post-buckled tapered two-directional functionally graded (2D-FG) microbeams is presented in this study. In the context of the modified couple stress theory, the formulations are derived based on the parabolic shear deformation beam theory and von Karman nonlinear strains. Different thermomechanical material properties are assumed to be temperature-dependent and smoothly vary in both length and thickness directions using the power law and the physical neutral axis concept is employed. The nonlinear governing equations are derived using the Hamilton principle and the resulting variable coefficient equations of motion are solved using the differential quadrature method (DQM) and iterative Newton's method for clamped-clamped and simply supported boundary conditions. Comparison studies are presented to validate the derived model and solution procedure. The impacts of induced thermal moments, temperature power index, two gradient indices, nonuniform cross-section, and microstructure length scale parameter on the frequency-temperature configurations are explored for both clamped and simply supported microbeams.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2625-2632
• /
• 2024

In this study, we investigated the possibility of employing accident tolerant fuel (ATF) in VVER-1200/V491 assembly without gadolinium-containing fuel rods using the Monte Carlo code Serpent 1.1.7 with ENDF/B-VII cross-section library. The analysis involves assembly design with reflective boundary conditions. To compare the neutronic performances, U-5Mo, U-7.5Mo, U-10Mo, and U-15Mo fuels were chosen in addition to ordinary UO₂ fuel. The concentration of ¹³⁵Xe, ¹⁴⁹Sm, fissile and fertile isotopes with burnup, reactivity feedback with fuel temperature variation, and β eff values were calculated. The results indicate that the fuel cycle length increases by 54.27% for U-5Mo, 32.6% for U-7.5Mo, and 13.8% for U-10Mo, while it decreases by 16.4% for U-15Mo fuel. Additionally, the effect of ⁹⁵Mo content in natural Mo was investigated by reducing the ⁹⁵Mo concentration. According to the results, each proposed fuel's fuel cycle length extended when the depletion ratio of ⁹⁵Mo increased. Additionally, the calculations for reactivity feedback guarantee safe operating conditions for all U-xMo fuels.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.1
• /
• pp.2853-2877
• /
• 1973

Models of cross-sections and channels were made in order to measure seepage losses. Cross-sections were made of sand, sandy clay loam and loam, their thicknesses being 30cm and 40cm, respectively. Flow depths kept in the cross-sections were 4cm, 6cm, 8cm and 10cm. Straight and curved channel models were provided so as to measure seepage losses, when constant water depths maintained at the heads of the channels were 7.3cm and 5.7cm, respectively. The results obtained in this experiment are presented as follows: 1) A cumulative seepage loss per unit length at a point in the channel varies in accordance with time and flow depth. The general equation of cumulative seepage loss may be as follows(Ref. to Table V.25): $$q_{cum}=\int_{o}^aq(a)dt+\int_a^bq(b)dt+\int_b^tq(c)dt$$ 2) In case that the variation of water depth through the channel is slight, the total seepage loss may be computed by applying the following general equation: $$\={q}_{cum}{\cdot}x=\int_o^tq_{cum}\frac{{\partial}x}{{\partial}t}dt$$ 3) Because seepage loss varies considerably according to water depth in case that the variation of flow depth through the channel is great, seepage loss should be computed by taking account of the change of flow depth. 4) The relation between time and traveling distance of water flow may be presented as the following general equation(Ref. to Table V.29): $$x=pt^r$$ 5) The ratios of the seepage losses of the straight channel to the curved channel are 1:1.03 for a flow depth of 7.3cm and 1:1.068 for that of 5.7cm. 6) The ratios of the seepage losses occurring through the bottom to those through the inclined plane in the channel cross-section are 1:2.24 for a water depth of 8cm and 1:2.47 for a depth of 10cm in case that soil-layer is 30cm in thickness. Similarly, those ratios are 1:2.62 and 1:2.93 in case of a soil-layer thickness of 40cm(Ref. to Table V.5).

• Advances in aircraft and spacecraft science
• /
• v.5 no.4
• /
• pp.445-458
• /
• 2018

Turbulent airflow in channels of rectangular cross section with symmetric centerbodies is studied numerically. Shock wave configurations formed in the channel and in front of the entrance are examined. Solutions of the unsteady Reynolds-averaged Navier-Stokes equations are obtained with finite-volume solvers of second-order accuracy. The solutions demonstrate an expulsion/swallowing of the shocks with variations of the free-stream Mach number or angle of attack. Effects of the centerbody length and thickness on the shock wave stability and flow bifurcation are examined. Bands of the Mach number and angle of attack, in which there exist non-unique flow fields, are identified.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.6
• /
• pp.1035-1038
• /
• 2007

We designed and manufactured a 1.8T high temperature superconducting(HTS) insert coil for a NMR magnet operated at 4.2 K. Suitable HTS superconductor and HTS coil were carefully designed and developed. We have selected multi-filamentary Bi2223 conductor fabricated by American Superconductor Corporation(AMSC). The selected conductor consists of Bi2223 filaments of 55, silver stabilizer and stainless steel reinforcement tapes. Therefore, it shows good hoop strength as well as compression tolerance. The conductor has a tape cross-section of 0.31mm x 4.8mm. the Bi2223 conductor shows large anisotropy of critical current. The critical current of conductor in magnetic field parallel to the flat surface are much higher than that in magnetic field perpendicular. The HTS coil has an inner diameter of 78 mm, an outer diameter of 127 mm and a coil length of 600 mm. In this paper, the detailed design, fabrication and test results on the HTS insert coil are presented.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.107-112
• /
• 1993

The objective of this experimental investigation is to examine the feasibility and the usefulness of the complementary crosstie in the current ACI 318-89 code for rienforced concrete columns subjected to constant axial load and lateral load reversals. Tests were conducted on1/3 scaled four columns with the length of 1.9m and the cross section of 20$\times$20 cm. The main parameters of specimens were the magnitude of axial load applied and the configuration of transverse reinforcements . From the experimental results, it can be seen that while the column subjected to lower axial load represented considerable ductility behaviors, the column subjected to higher axial load showed the brittle failure

• Tribology and Lubricants
• /
• v.27 no.3
• /
• pp.156-161
• /
• 2011

The rectangular waveguide technique can be used to measure the complex permittivity of dielectric material of various thickness and cross section. This paper presents the analysis system of engine oil permittivity at which deterioration of engine oil is measured at the X-band(8-12.5 GHz). The middle of the rectangular waveguide has engine oil case and is connected with VNA(Vector Network Analyzer) for the measurement of the transmission$(S_{21})$ and reflection$(S_11)$ and then the permittivity is extracted. The deterioration of engine oil is proved by the comparison with both the extracted data and reference data. As the additional research, This paper suggest that an accurate permittivity is considered by not only the wave guide length but the air gap between oil case and the waveguide.

• Water for future
• /
• v.20 no.4
• /
• pp.249-256
• /
• 1987

Wave forces on fixed two-dimensional objects submerged in water of finite depth were analysed by Boundary Element Method using linear elements.It is assumed that the wave forces may be described by linear theory and that incident wave direction is normal to the objects of infinite length. In this paper, wave forces on a bottom-seated half cross section pipeline, a circular pipeline, a submerged pipeline and submerged breakwater of arbitrary shape were studied. The accuracy of the computational scheme is investigated by comparing the numerical results with the existing laboratory results and analytical solutions of other researchers.