• Structural Engineering and Mechanics
• /
• v.14 no.3
• /
• pp.365-380
• /
• 2002

Following a series of experiments on isolated low-rise RC shear walls with openings, a theoretical study on the backbone curve of a perforated shear wall shows that there are some important observations from experimental results that make clear a semi-empirical formula of the backbone curve of a perforated wall. Critical shear zones can be depicted from the configuration of shear walls with openings. Different factors, including the size and location of shear wall openings, the wall's height/width ratio, horizontal and vertical steel bar ratios, and location and amount of diagonal steel bars are involved in the derivation of the backbone curve. Bending and shear effects are also considered in the paper. In addition, a comparison of load and displacement for solid and perforated shear walls is discussed. Generally, the comparison between experimental curves and computed backbone curves is favorable.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.415-420
• /
• 1998

In this paper, 2D SUB-3D STM approach for analysis and design of 3D structural concrete is presented. In the approach several 2D sub strut-tie models which are representations of compressive and tensile stress flows of each projected plane of 3D structural concrete are utilized in the sketch of a 3D strut-tie model, in the evaluation of effective strengths of compressive concrete struts, and in the verification of geometric compatibility and bearing capacity of critical nodal zones of 3D strut-tie model. To prove the validity and rationality of the suggested approach, the behavior and strength of a prestressed box girder diaphragm tested to failure are evaluated.

• International Journal of Automotive Technology
• /
• v.5 no.4
• /
• pp.297-302
• /
• 2004

This paper presents the low cycle thermal fatigue of the engine exhaust manifold subject to thermo-mechanical cyclic loading. As a failure of the exhaust manifold is mainly caused by geometric constraints of the less expanded inlet flange and cylinder head, the analysis is based on the exhaust system model with three-dimensional temperature distribution and temperature dependent material properties. The result show that large compressive plastic deformations are generated at an elevated temperature of the exhaust manifold and tensile stresses are remained in several critical zones at a cold condition. From the repetition of these thermal shock cycles, maximum plastic strain range (0.454%) could be estimated by the stabilized stress-strain hysteresis loops. It is used to predict the low cycle thermal fatigue life of the exhaust manifold for the thermal shock test.

• Journal of Korea Foundry Society
• /
• v.20 no.3
• /
• pp.197-207
• /
• 2000

Al-Si alloys were solidified in a rotating cylindrical mold by a vertical centrifugal casting process. Under a certain casting condition, there are four distinct zones such as the chill zone, the primary fine columnar zone, the equiaxed zone, and the secondary coarse columnar zone from the mold wall. The columnar-equiaxed transition (CET) and the equiaxed-columnar transition (ECT) were measured as functions of solute content, flow rate (mold velocity), pouring temperature and mold temperature. Within the critical value of solute content, as the flow rate increases, the columnar-equiaxed transition were found, but not the equiaxed-columnar transition. The aspect ratio of the primary columnar zone was more affected by the solute content than the flow rate. However the aspect ratio of the equiaxed zone was more affected by the flow rate than the solute content. The aspect ratio of the secondary columnar zone was affected by both the flow rate and the solute content.

• International Journal of Aeronautical and Space Sciences
• /
• v.1 no.2
• /
• pp.30-42
• /
• 2000

On-orbit thermal environment test of KOMPSAT was performed in early 1999. An analysis of the test data are addressed in this paper. For the thermal-environmental simulation of spacecraft bus, an artificial heating through the radiator zones and onto some critical heat-dissipating electronic boxes was made by Absorbed-heat Flux Method. Test data obtained in terms of temperature history were reduced into flight heater duty cycles and converted into the total electrical power required for spacecraft thermal control. Verification result of flight heaters dedicated to the bus thermal control is presented. Additionally, an exhaustive heating-control process for maintaining the spacecraft thermally safe and for realistic simulation of the orbital-thermal environment during the test are graphically shown. Qualitative suggestions to post-test model correlation are given in consequency of the analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.160-165
• /
• 2007

Exhaust manifold is generally subjected to thermal cycle loadings ; at hot condition, large compressive plastic deformations are generated, and at cold condition, tensile stresses are remained in highly deformed critical zones. These phenomena originate from that thermal expansions of the runners are restricted by inlet flange connected to the cylinder head, because the former is less stiff than the latter and, the temperature of the inlet flange is lower than that of the runners. Therefore, due to the repetitions of thermal deformation, leakage problems could be occur between inlet flange and cylinder head. In this study, we obtained pressure distributions along gasket bead lines from the finite element analysis and compared to the test results. It shows a good agreement between numerical and experimental results.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.39-46
• /
• 2001

It is noted that KS D 3507 pipe steel has several problems when it is used as a city gas pipe at medium pressure. So new pipe steel, KS D 3631, was developed in order to be used as a pipe for medium and low pressure and now it is being substituted for D 3507. In this study, several mechanical tests, such as tensile test, microhardness test, and Charpy impact test were conducted to get material properties of D 3507 and D 3631 pipe steels. And also microstructures at the weld and heat affected zones were observed for the two materials. From the Charpy test results $K_{IC}/$ was estimated for the upper and lower shelf and the critical crack length is calculated for supposed axial semi-elliptical surface cracks. And the burst pressure is estimated as a function of wear depth for a defective D 3631 pipe by using the finite element method. The burst pressure is also calculated for pipes with an axial crack by using the published equations.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.139-145
• /
• 2007

This paper presents the low cycle thermal fatigue of the engine exhaust manifold subject to thermomechanical cyclic loadings. The analysis includes the FE model of the exhaust system, temperature dependent material properties, and thermal loadings. The result shows that at an elevated temperature, large compressive plastic deformations are generated, and at a cold condition, tensile stresses are remained in several critical zones of the exhaust manifold. From the repetitions of thermal shock cycles, plastic strain ranges could be estimated by the stabilized stress-strain hysteresis loops. The method was applied to assess the low cycle thermal fatigue for the engine exhaust manifold. It shows a good agreement between numerical and experimental results.

• Proceedings of the KOR-KST Conference
• /
• 1998.09a
• /
• pp.141-151
• /
• 1998

Provision of Passing Sight Distance (PSD) is an important component in two-lane highway design and has a critical impact on capacity of highway and safety of drivers. Many models have been developed to estimate PSD reasonably. However, each of them has a number of shortcomings for reflecting the real traffic conditions. This paper introduces a revised model that reflects the characteristics of the passing maneuver. The changes in passing sight distances under different assumptions about acceleration and vehicle length, which are related to vehicle types, are presented. The results obtained by the revised model are compared with those obtained from the existing models. There is an important link between geometric design decisions which determine the available sight distance and the quality of service which the road provides. In this paper, we examine one aspect of this relationship. That is to determine whether the passing sight distance is provided by improving horizontal alignment for a specific roadway section or passing may be restricted to save the road construction cost. To do so, a simple method for estimating traffic delay in no-passing is introduced.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.385-399
• /
• 2000

Groundwater contamination caused by landfill leachate leads to various changes in aquifer environment according to the characteristics of incoming contaminants and aquifer geochemistry. These changes in aquifer environment are known to contribute to the natural attenuation phenomena of contaminants. The knowledge on changes in aquifer environment is necessary to determine the extent of groundwater pollution, to assess risk of the pollution, and to develop an appropriate remediation technologies. In this paper, the changes in aquifer environment caused by landfill leachate development of various redox zones-and the natural attenuation phenomena occurred in each redox zone are reviewed. From this review, an appropriate research direction and control action is presented for the groundwater pollutions caused by unsanitary landfills scattered across the nation.