지속하중하(持續荷重下)의 점토지반(粘土地盤) 또는 사면(斜面)을 형성(形成)하고 있는 점토(粘土)는 시간의존변형(時間依存變形)을 일으키고 어떤 경우 파괴(破壞)에 이르기도 하는데 그 원인(原因)은 점토(粘土)의 Creep 거동(擧動) 때문이라는 보고(報告)가 대부분(大部分)이다. Creep 거동(擧動)은 많은 요소(要素)에 관련될 뿐 아니라 특(特)히 함수비(含水比) 및 응력수준(應力水準)에 큰 영향(影響)을 받기 때문에 매우 복잡(複雜)하며 따라서 그 거동(擧動)을 해석(解析) 하기도 어려운 일인데 Creep이 궁극적(窮極的)으로는 점토(粘土) 입자간(粒子間)의 미시적(微視的)인 거동(擧動)에서 비롯되기 때문이다. 응력(應力)-변형(變形)-시간(時間) 관계(關係)로서의 Creep 거동(擧動)을 수학적(數學的)으로 표현(表現)하기 위하여 여러 형태(形態)의 유변학적(流變學的) 모델이 제안(提案) 되었다. 유변학적(流變學的) 모델은 선형(線形) 스프링, 비선형(非線形) Dashpot 및 Slider를 조합(組合)한 것인데 점토(粘土)의 변형(變形)에 관한 탄성적(彈性的), 소성적(塑性的) 및 점성적(粘性的) 성분(成分)을 구분(區分) 하는데 매우 유용(有用)하다. 그러나 대부분(大部分)의 경우, 유변학적(流變學的)모델은 포화(飽和)된 점토(粘土)에 대(對)하여 주(主)로 2차압밀(次壓密) 거동(擧動)을 밝히기 위하여 제안(提案)된 것으로 비포화점토(非飽和粘土)에 대(對)한 보고(報告)는 매우 드문 것 같다. 한편, Creep 거동(擧動)은 시간의존변형(時間依存變形)이므로 흐트러진 점토(粘土)를 다져서 시험(試驗)하는 경우, 시간경과(時間經過)에 따라 Thixotropy 문제(問題)가 제기(提起)될 것이고 배수조건(排水條件)과 관련하여서는 공시체(供試體)의 높이가 문제(問題)될 수 있다. 그뿐 아니라 많은 연구결과(硏究結果)에 의(依)하면 응력증가초기(應力增加初期)에는 시간지체(時間遲滯)가 없는 초기탄성변형(初期彈性變形)이 발생(發生)된다고 하므로 유변학적(流變學的) 모델에는 이를 나타내는 요소(要素)가 반드시 필요(必要)하게 될 것이다. 본(本) 연구(硏究)는 이러한 면(面)에 초점(焦點)을 두고 함수비(含水比)와 응력수준(應力水準)을 여러 가지로 변화(變化)시켰을 때의 Creep 거동(擧動)을 유변학적(流變學的) 모델로 해석(解析)함에 있어 소성(塑性)이 비교적(比較的) 큰 3종(種)의 점토(粘土)를 사용(使用)하여 초기탄성변형(初期彈性變形) 거동(擧動)을 밝히고 Thixotropy 효과(効果) 및 공시체(供試體)의 높이가 Creep 거동(擧動)에 끼치는 영향(影響)을 구명(究明)하며 아울러 유변학적(流變學的) 모델의 어떤 요소(要素)에 관련 되는가를 알아내기 위하여 다져서 성형(成形)한 공시체(供試體)로서 일축배수형식(一軸排水形式)의 Creep 거동(擧動)을 시행(施行)하였다. 실험결과(實驗結果) 및 검토(檢討)에 의(依)하면 응력재하(應力載荷) 및 증가초기(增加初期)에는 시간지체(時間遲滯)가 없는 탄성적(彈性的) 초기변형(初期變形)이 발생(發生)하고 따라서 유변학적(流變學的) 모델에는 이를 나타내기 위한 상부(上部)스프링을 설치(設置)해야 하며 Thixotropy 효과(効果)를 고려(考慮)한 경우, Creep변형(變形)은 완만(緩慢)하게 되나 함수비(含水比) 및 응력수준(應力水準)에 따른 상태거동(狀態擧動)은 같으므로 그 차이(差異)는 모델 상수(常數)의 크기에만 관련됨을 알아내었고 따라서 동일(同一)한 유변학적(流變學的) 모델로 그 거동(擧動)을 나타낼 수 있다는 사실(事實)을 밝혀 냈다. 또 공시체(供試體) 높이를 작게 한 경우에는 함수비(含水比)가 비교적(比較的) 작아서 점(粘)-소(塑)-탄성(彈性) 및 점(粘)-탄성(彈性)일 때만 높이가 클 때와 같은 상태거동(狀態擧動)을 나타내어 동일(同一)한 유변학적(流變學的) 모델로 나타낼 수 있고 함수비(含水比)가 큰 점일소성(粘一塑性) 및 점성류(粘性流)일 때는 그 상태거동(狀態擧動)이 배수문제(排水問題)와 관련하여 달라지게 되고 따라서 유변학적(流變學的) 모델도 달라지게 된다는 사실(事實)을 발견(發見) 하였다.
Recent results obtained for the port-pom model and the constitutive equations with time-strain separability are examined. The time-strain separability in viscoelastic systems Is not a rule derived from fundamental principles but merely a hypothesis based on experimental phenomena, stress relaxation at long times. The violation of separability in the short-time response just after a step strain is also well understood (Archer, 1999). In constitutive modeling, time-strain separability has been extensively employed because of its theoretical simplicity and practical convenience. Here we present a simple analysis that verifies this hypothesis inevitably incurs mathematical inconsistency in the viewpoint of stability. Employing an asymptotic analysis, we show that both differential and integral constitutive equations based on time-strain separability are either Hadamard-type unstable or dissipative unstable. The conclusion drawn in this study is shown to be applicable to the Doi-Edwards model (with independent alignment approximation). Hence, the Hadamardtype instability of the Doi-Edwards model results from the time-strain separability in its formulation, and its remedy may lie in the transition mechanism from Rouse to reptational relaxation supposed by Doi and Edwards. Recently in order to describe the complex rheological behavior of polymer melts with long side branches like low density polyethylene, new constitutive equations called the port-pom equations have been derived in the integral/differential form and also in the simplifled differential type by McLeish and carson on the basis of the reptation dynamics with simplifled branch structure taken into account. In this study mathematical stability analysis under short and high frequency wave disturbances has been performed for these constitutive equations. It is proved that the differential model is globally Hadamard stable, and the integral model seems stable, as long as the orientation tensor remains positive definite or the smooth strain history in the flow is previously given. However cautious attention has to be paid when one employs the simplified version of the constitutive equations without arm withdrawal, since neglecting the arm withdrawal immediately yields Hadamard instability. In the flow regime of creep shear flow where the applied constant shear stress exceeds the maximum achievable value in the steady flow curves, the constitutive equations exhibit severe instability that the solution possesses strong discontinuity at the moment of change of chain dynamics mechanisms.
In this study, the properties of super flowing cocrete containing gly ash were experimentally investigated and compared with those of ordinary concrete. Tests were carried out on five types of super flowing concrete mixes containing fly ash and three types of ordinary concrete mixes without fly ash. Flow test, O-funnel test, box test, Ltype thest and slump test were carried out to obtain the properties for the workability of fresh concrete. Compressime strength, splitting tensile strength, modulus of elasticity. creep and shrinkage test were also obtained as the mechanical properties of hardened concrete. In fresh concrete, it was found that super flowing concrete had excellent workability and flowability compared with ordinary concrete, and the volume ratio of coarse aggregate to concrete volume greatly influenced flowability. Super flowing concrete also had good mechanical properties at both early and late ages with compressive strengths reaching as high as 40 MPa at 28 days. The creep deformation of super flowing concrete investigated were relatively lower than that of ordinary concrete.
KIEE International Transactions on Electrophysics and Applications
/
제5C권5호
/
pp.204-210
/
2005
Alternating current (AC) losses of two Bi-2223 ([Bi, Pb]: Sr: Ca: Cu: O = 2:2:2:3) tapes [(Tape I, un-twist-pitch) and the other with a twist-pitch of 10 mm (Tape II)] were measured and compared. These samples, produced by the powder-in-(Ag) tube (PIT) method, are multi-filamentary. Also, it's produced by non-twist and different twist pitch (8, 10, 13, 30, 50 and 70 mm). The critical current measurement was carried out under the environment in liquid Nitrogen and in zero-field by 4-probe method. Susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation. Neutron-diffraction measurements have been carried out investigate the crystal structure, magnetic structures, and magnetic phase transitions in Bi-2223([Bi, Pb]:Sr:Ca:Cu:O)
KIEE International Transactions on Electrophysics and Applications
/
제3C권6호
/
pp.211-215
/
2003
Alternating current (AC) losses of two Bi-2223 ([Bi, Pb] : Sr : Ca : Cu :O = 2:2:2:3) tapes [one untwisted (Tape I, twist-pitch of $\infty$ mm) and the other with a twist-pitch of 8mm (Tape II) ] were measured and compared. These samples, produced by the powder-in-tube (PIT) method, are multi-filamentary and have a Ag/Au and Ag matrix, respectively. Susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation.
Needs of fuel's performance evaluation for the dual-cooled fuel pellet (annular shape) necessitate the irradiation test in the test reactor. Irradiation test rig for the HARARO reactor, which is a special-purposed equipment used for material, irradiation and creep test, must satisfy the operational requirement on the hydraulic characteristics and structural integrity. In this paper, pressure drop and flow-induced vibration test for the newly developed non-instrumented test rig were carried out using FIVPET as a out-pile evaluation test. The test results show that the new test rig satisfy the HANARO operational requirement with sufficient margin. The spectral response characteristics of the flow-induced vibration of the test rid were also discussed.
It is well known that Fe3Al intermetallic compound shows an anomalous peak of the yield strength at about 50$0^{\circ}C$ and then decrease at higher temperatures The dislocation structure was examined by transmission electron microscopy and high temperatures. The dislocation structure was examined by transmission electron microscopy and high temperature mechanical properties were examined by tensile and load relaxation tests. The flow stress curves obtained from load relaxation tests were then analyzed in terms of internal variable deformation theory. it was found that the flow curves consisted of three micro-deformation mechanisms -i. e inelastic deformation mode plastic deformation mode and dislocation creep deformation mode depending on both dislocation structure and deformation temperature. The flow curves could be well described by the constitutive equations of these three micro-deformation mechanisms based on the internal variable deformation theory.
Recently in order to describe the complex rheological behavior of polymer melts with long side branches like low density polyethylene, new constitutive equations called the pom-pom equations have been derived by McLeish and Larson on the basis of the reptation dynamics with simplified branch structure taken into account. In this study mathematical stability analysis under short and high frequency wave disturbances has been performed for the simplified differential version of these constitutive equations. It is proved that they are globally Hadamard stable except for the case of maximum constant backbone stretch (λ = q) with arm withdrawal s$\_$c/ neglected, as long as the orientation tensor remains positive definite or the smooth strain history in the now is previously given. However this model is dissipative unstable, since the steady shear How curves exhibit non-monotonic dependence on shear rate. This type of instability corresponds to the nonlinear instability in simple shear flow under finite amplitude disturbances. Additionally in the flow regime of creep shear flow where the applied constant shear stress exceeds the maximum achievable value in the steady now curves, the constitutive equations will possibly violate the positive definiteness of the orientation tensor and thus become Hadamard unstable.
The viscoplasticity theory based on overstress, one of the unified state variable theories, is generalized to model zero (no influence of loading rate) and negative (flow stress decreases with loading rate) as well as positive (flow stress increases with loading rate) rate sensitivity in a consistent way. On the basis of the long-time asymptotic solution the different types of rate sensitivity are classified with respect to an augmentation function that is introduced in the evolution law fur a state variable equilibrium stress. The theory predicts normal relaxation and creep behaviors even if unusual rate sensitivity is modeled. The constitutive model fir the behavior of a modified 9Cr-1 Mo steel at various temperatures is then compared with experimental data found in the literature.
본 연구는 말뚝 부마찰력 저감용으로 사용하는 역청재료의 유변학적 특성을 분석한 결과이다. 역청재료는 효과적으로 부마찰력을 저감시키고 경제적인 장점으로 인하여 말뚝의 부마찰력 저감 공법으로 사용하여 왔다. 본 연구에서는 세 종류의 말뚝용 역청재료를 선택하여 비교 시험을 실시하였다. 물리적 특성시험으로는 침입도 시험, 연화점 시험 및 침입도 지수를 실시하였으며 유변학적 시험으로는 동적전단 유동기를 사용하여 위상각, 복합계수, 크리프시험 및 흐름시험을 시험온도 15, 30, 45 및 6$0^{\circ}C$에서 수행하였다. 시험 결과는 역청재료의 유변학적 특성을 나타내는 위상각, G$^*$/sin $\delta$, 크리프 컴플라이언스 및 전단점도로 분석하여 상호 비교하였다. 시험 결과 온도와 위상각은 비례관계를 나타냈으며 G$^*$/sin $\delta$는 반비례 관계를 보였다. 또한, 크리프 컴플라이언스는 하중시간이 증가함에 따라 증가하여 역청재료가 시간의 변화에 따라 점성유체로 작용하는 것으로 나타났다. 크리프시험으로 인한 시간 및 온도의 변화는 크리프 컴플라이언스 값을 크게 변화 시켰으나 전단점도의 변화는 그다지 심하게 나타나지 않아서 말뚝 역청재료의 평가에는 크리프 컴플라이언스를 측정 할 수 있는 크리프시험이 적절한 것으로 평가되었다. 본 연구에서 유변학적 시험을 실시한 결과 물리적 시험으로부터 분석할 수 없는 온도와 시간의 변화에 따른 역청재료의 특성변화를 상세하게 분석할 수 있었는데 이러한 시험 결과는 말뚝용 역청재료의 선정에 큰 영향을 미칠 것으로 판단된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.