• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.11
• /
• pp.27-35
• /
• 1995

The fluid coupling combined with a pump and a turbine have many merits compared with other couplings, their uses are increesing rapidly in various industrial fields at home and abroad in pursuit of high-speed more efficiency durability of various mechanic devices. The authorities concerned have recognized the improtance of the fluid coupling and supported its developement and now some trial products began to show up. As the structrue and characteristics of the fluid coupling have little similarity to other kinds of couplings and its fluid behavior is unique, so its characteristic analysis is expected to be difficult. Until now no satisfactory study on the characteristics of the fluid coupling seems to have been conducted at home, so a study on this field needs to be done urgently. The purpose of this research is to construct the experimental test set-ups and establish a series of performance test program for the domestically developed fluid couplings and to provide a software to store and utilize these experimental data which can be used to improve the performance of the fluid coupling and solve on the job problems confronted in operation. The performance test consists of taking measurment of torque, rpm and efficiency of the fluid coupling for three different amount of working fluid inside with various loads to the output shaft and finally infestigating the torque, rpm and efficiency characteristics of the fluid coupling with respect to these parameters. The results of this study can contribute valuable references to the development of variable speed fluid coupling and torque converter currently pursued by the domestic industry.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.696-701
• /
• 2014

In this study, in order to develop coupled vibration mode piezoelectric devices for Acoustic Emission (abbreviated as AE) sensor application with outstanding displacement and piezoelectric properties have been simulated by ATILA FEM program. And, From the results of ATILA simulation, the AE sensor specimen, obtained superior electromechanical coupling factor and displacement, when the size of specimen is $3.45mm{\Phi}{\times}3.45mm$ with ratio of diameter/thickness(${\Phi}/T$)= 1.0. Therefore, AE sensor was fabricated by (Na,K,Li)(Nb,Ta) $O_3$(abbreviated as NKL-NT) system piezoelectric ceramics using coupled vibration mode. The piezoelectric properties of NKL-NT ceramics was exhibited that piezoelectric constant($d_{33}$), piezoelectric voltage constant($g_{33}$) and electro mechanical coupling factor($k_p$) have the excellent values of 261[pC/N], 40.10[$10^{-3}Vm/N$], and 0.44, respectively. The manufactured piezoelectric device with ratio of ${\Phi}/T$= 1.0 indicated the optimum values of resonant frequency(fr)= 556.5[kHz], antiresonant frequency(fa)=631.1[kHz], and effective electromechanical coupling factor(keff)= 0.473. The maximum sensitivity of the coupled vibration mode AE sensor was 55[dB] at the resonant frequency of 75[kHz]. The results show that the coupled vibration mode piezoelectric device is a promising candidate for the application AE sensor piezoelectric device.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.12-16
• /
• 2004

We show that the extinction ratio is improved using slight asymmetry in two core refractive indices of polarization independent very short vertical directional couplers with the double-sided deep-ridge (DSDR) waveguide structure. The optimum asymmetry with the maximum extinction ratio and the tolerance of the refractive index of core with the extinction ratio larger 1ha]1 30 ㏈ increase as the thickness of inner cladding layer and the two cores decrease due to the increase of the coupling strength between the two cores. Also, the device length and the tolerance of the device length with the extinction ratio larger than 30 ㏈ decrease as the thickness of the inner cladding layer and the two cores decrease due to the increase of the coupling strength between the two cores. We show that polarization independent vertical directional couplers with the DSDR waveguide structure with the device length less than 100 ${\mu}{\textrm}{m}$ and the extinction ratio larger than 30 ㏈ could be implemented.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.280-285
• /
• 2007

Based on the multimode fiber taper, a mode size converter for effective optical beam coupling between laser and optical fiber or between the two different optical fibers has been proposed and demonstrated. The device has a multimode input end and a single mode output end. The influence of various parameters, including device structure and launching conditions, on the coupling efficiency has been theoretically analyzed. The theoretical results revealed that the gaussian beam can be coupled into a single mode fiber without considerable insertion loss. The proposed multimode fiber taper has been fabricated using heating and pulling equipment incorporating two micro-torches. Experimental results showed that an optical beam with $50\;{\mu}m$ of large beam size was effectively coupled into single mode fiber through the multimode fiber taper. The insertion loss of the device was 1.3 dB.

• Journal of the Korean Magnetics Society
• /
• v.25 no.1
• /
• pp.22-26
• /
• 2015

In this paper, a magneto-inductive wave generated in a chain of LC resonators fabricated with Ni-Zn ferrite cores and chip capacitors is presented. RF signal propagates to neighbor resonator one by one as a consequence of the magnetical coupling between two resonators in the device. The magnetical coupling is due to the mutual inductances along the chain of resonators. So, the signal amplitude (${\approx}$ coupling intensity) is dependent of the mutual inductance which can be adjusted by applied magnetic field. In order to demonstrate the device, some experiments have been carried out systemically. The transmission characteristics of a magneto-inductive wave could be controlled by applied external magnetic field. The device composed of 5 resonators; the center frequencies were estimated to be 32 MHz and 38 MHz with the external magnetic flux density of 75 Oe and 222 Oe, respectively. We expect that the reported results could open a promising way to a high variety of applications in one- and two-dimensional functional devices, such as transducers, delay lines, power dividers and couplers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.1
• /
• pp.44-49
• /
• 2018

This study analyzed the Vulnerability of Network Communication devices when IEMI is coupled with the Network System. An Ultra Wide Band Generator (180 kV, 700 MHz) was used as the IEMI source. The EUTs are the Switch Hub and Workstation, which are used to configure the network system. The network system was monitored through the LAN system configuration, to confirm a malfunction of the network device. The results of the experiment indicate that a malfunction of the network occurs as the electric field increases. The data loss rate increases proportionally with increasing radiating time. In the case of the Switch Hub, the threshold electric field value was 10 kV/m for all conditions used in this experiment. The threshold point causing malfunction was influenced only by the electric field value. The correlation between the threshold point and pulse repetition rate was not found. However, in case of the Workstation, it was found that as the pulse repetition rate increases, the equipment responds weakly and the threshold value decreases. To verify the electrical coupling of the EUT by IEMI, current sensors were used to measure the PCB line inside the EUT and network line coupling current. As a result of the measurement, it can be inferred that when the coupling current due to IEMI exceeds the threshold value, it flows through the internal equipment line, causing a malfunction and subsequent failure. The results of this study can be applied to basic data for equipment protection, and effect analysis of intentional electromagnetic interference.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.2
• /
• pp.78-83
• /
• 2019

In this study, we analyze the structure of the transceiver coil in the inductive power transfer (IPT) system. In the IPT system, the transceiver coil design needs to have the highest magnetic coupling possible because of the relatively low magnetic coupling due to the large gap of distance without the core. The transmitting coil may be formed as a multi-layer type according to the distance between the transmitting and receiving coils if the receiving coil is configured as a multi-layer type on the inner structure of the receiving apparatus, thereby improving the magnetic coupling and system efficiency. We compare and analyze the coil magnetic coupling, and system efficiency according to the layer structure of the transmitting and receiving coils and verify the analysis by JMAG simulation. Experimental results show that the layer structure of the transceiver should be considered according to the inner space of the receiving device and the spacing distance.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.522-528
• /
• 2017

In this paper, we propose a multi-band antenna for wearable devices using metal frame coupling. The proposed antenna has a $45mm{\times}35mm$ antenna using metal frame and a ground dual coupling structure. The proposed multi-band antenna in this paper is optimized for small devices such as wearable devices. By using the metal frame as a part of the antenna, the volume of the antenna is reduced and satisfies under VSWR 3:1 impedance bandwidth of 70 MHz (870 ~ 940 MHz) in low frequency band, 280 MHz (1600 ~ 1880 MHz) and 280 MHz (1900 ~ 2170 MHz) in high frequency band. It also verified the applicability of wearable devices by measuring wireless performance indicators such as TRP/TIS.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.586-594
• /
• 2013

This paper proposes a new coupling element of microwave slot coupler for designing waveguide slot array which can reduce the effect of undesired higher order mode coupling between coupling and radiating slots in the branch waveguide. The proposed device is composed of a centered longitudinal shunt-series coupling slot at the center of broad wall shared by two crossed rectangular waveguides and an asymmetric compound iris that excites the coupling slot. We first have obtained scattering parameters for the proposed coupler by use of EM S/W tool HFSS and then extracted the parameters of T- network equivalent circuit for the coupling slot. We also have analyzed the resonant properties such as resonant length and normalized admittance by changing the geometrical dimensions. The measured results for the fabricated coupler with short-circuited block ${\lambda}_g/4$ away from the coupling slot are well agreed with the simulated ones.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.165-166
• /
• 2023

Free-form Concrete Panel(FCP) is each panel that composes the concrete exterior skin of Free-form building. FCPs contain curved surfaces, and FCPs have different curvature, size, and angles. In order to manufacture FCP, high technology is required, and it is currently difficult to manufacture it according to the design shape. In particular, many errors occur in the side shape of FCP. This is because when the side silicone mold is applied, it is installed without a coupling method between molds and support device. In this study, basic research was conducted to develop a side silicone mold support device to solve the above problems. We classified the required performance and derived the detailed requirements. Also, Based on this, we drew the basic design of the support device. We plans to conduct design improvement, mock-up making, and FCP manufacturing experiments through future research.