• 한국해양공학회지
• /
• 제9권2호
• /
• pp.141-148
• /
• 1995

Fatigue tests were carried out by a rotary bending testing machine of cantilever type. M.E.F.(ferrite encapsulated islands of martensite) materials were made by a series of heat treatment from a low carbon steel(SM 20 C). The fatigue tests were conducted at stress levels of 302 MPa and with frequencies of 25Hz, 2.5 Hz and 0.5 Hz in 3% NaCl solution. The fatigue strength increased with frequency got higher. The microcracks and corrosion pits were generated at the boundary between the matrix and the 2nd phase. The cracks generated by the corrosion pits were coalesced with the pits around the notch and became the initial crack. The $N_i/N_f$ ratio increased as the frequency and stress level decreased. The interference phenomenon increased with stress level and frequency gots higher. The crack propagation rate was delayed as the stress level lowers and the frequency gets higher, however, the range of the stress intensity factor depended only on a stress level.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.20-25
• /
• 2000

lh deleterious Cr, Mo rich -$\sigma$phase is a hard embrittling precipitate, which forms between MU)-900 $^{\circ}C$, often associated with a reduction in both impact properties and corrosion reshame. On this study, After aging at MU) "C, fatigue crack propagation induced by a phase precipitation was evaluated and time-frequency analysis of acoustic emission was conducted It was possible to find fracture mechanism by a phase precipitation due to time-frequency anulysis of acoustic emission signals.nals.

• 한국해양공학회지
• /
• 제6권2호
• /
• pp.76-84
• /
• 1992

In this study, corrosion fatigue test of SAPH45 steel was performed by the use of plane behavior of base metal (BM) and heat affected zone (HAZ) of SAPH45. The main results obtained are as follows: 1) The more aspect ratio (b/t) of corner crack decreases, the more aspect ratio (b/a) takes greatly effect by corrosion. 2) The correlation between the stress intensity factor range ($\Delta$k) and crack growth rate (da/dN) for weldment in seawater is given by Paris rule as follow: da/dN=C($\Delta$K) super(m). Where m is constant, and the value is 3.82-3.84. 3) The accelerative factor ($\alpha$) of BM and HAZ under seawater is about 1.1-1.9, and ($\alpha$) of HAZ increases more and more under the low $\Delta$K region. 4) HAZ is more susceptible to corrowion than BM because of potential of electrode (E sub(c)) of HAZ becomes more less noble potential than that of BM.

• 한국기계가공학회지
• /
• 제6권1호
• /
• pp.62-70
• /
• 2007

The development of new materials that are light-weight, yet high in strength has become vital to the machinery, aircraft and auto industries. However, there are a lot of problems with developing such materials that require expensive tools, and a great deal of time and effort. Therefore, the improvement of fatigue strength and fatigue life are mainly focused on by adopting residual stress. The fatigue crack growth rate of the Shot-peened material was lower than that of the Un-peened material. And in stage I, threshold stress intensity factor of the shot-peen processed material is high in critical parts unlike the Un-peened material. Also, fatigue crack growth exponent and number of cycle of the Shot-peened material was higher than that of the Un-peened material. That is concluded from effect of da/dN. And Fatigue life shows more improvement in the Shot-peened material than in the Un-peened material. And compressive residual stress of surface on the Shot-peen processed operate resistance force of fatigue crack propagation.

• 수산해양기술연구
• /
• 제28권1호
• /
• pp.61-70
• /
• 1992

In this study, corrosion fatigue test of SAPH45 steel was performed by the use of plane bending fatigue tester in marine environment and investigated fracture surface growth behavior of base metal and heat affected zone corrosion fatigue. The main results obtained are as follows: 1) Fracture surface growth of heat affected zone (HAZ) is delayed more than that of base matel (BM), and they tend to faster in seawater than in air. 2) Corrosion sensitivity to corrosion fatigue life of HAZ is more susceptible than that of BM. 3)In the case of the corner crack by corrosion fatigue, the correlation between the propagation rate of fracture surface area(dA/dN) and stress intensity factor range(ΔK) for SAPH45 are applied to Paris rule as follows: dA/dN=C(ΔK) super(m) where m is the slope of the correlation, and is about 6.60-6.95 in air and about 6.33-6.41 in seawater respectively.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.216-227
• /
• 1992

The corrosion rate, behavior of corrosion fatigue and characteristic of cathodic protection for SB41 were investigated by corrosion and corrosion control tests in seawater at laboratory and coast. The main result obtained are as the following; 1) The corrosion rate of base metal (BM) is about 28-37 mg/dm super(2) day in seawater of coast. 2) The correlation between the stress intensity factor range $\Delta$K and crack propagation rate da/dN for weldment follows paris' rule in seawater : da/dN=C($\Delta$K) super(m) where m is the slope of the correlation, and is 2.02 for BM and 1.75 for heat affected zone (HAZ) respectively. 3) The corrosion sensitivity of HAZ is more sensitive than that of BM under the low region of $\Delta$K. 4) With increase of bared surace area of cathode, cathodic protection potential is increased sharply.

• Structural Engineering and Mechanics
• /
• 제53권5호
• /
• pp.867-880
• /
• 2015

Mechanical fastening is still one of the main methods used for joining components. Different techniques have been applied to reduce the effect of stress concentration of notches like fastener holes. In this work we evaluate the feasibility of combining laser shock peening (LSP) and cold expansion to improve fatigue crack initiation and propagation of open hole specimens made of 6061-T6 aluminum alloy. LSP is a new and competitive technique for strengthening metals, and like cold expansion, induces a compressive residual stress field that improves fatigue, wear and corrosion resistance. For LSP treatment, a Q-switched Nd:YAG laser with infrared radiation was used. Residual stress distribution as a function of depth was determined by the contour method. Compact tension specimens with a hole at the notch tip were subjected to LSP process and cold expansion and then tested under cyclic loading with R=0.1 generating fatigue cracks on the hole surface. Fatigue crack initiation and growth is analyzed and associated with the residual stress distribution generated by both treatments. It is observed that both methods are complementary; cold expansion increases fatigue crack initiation life, while LSP reduces fatigue crack growth rate.

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.492-501
• /
• 1990

It was known that the fracture incidences of offshore structure were mostly originated from the surface defects. Especially, in the case of the welded structures, since the welded region has some defects and incomplete beads which are apt to behave like the surface cracks, it has been necessary to evaluate the environmental effects on crack growth at HAZ for the design crack growth behaviour at multi-pall HAZ for SWS41 steel under free corrosion and cathodic protection(-0.9V vs Ag/Agcl) conditions. The results are summarized as follows ; (1) Crack growth rate of the as weld in air was faster than that of the parent and PWHT specimens over all .DELTA.K rang. (2) In free corrosion test, surface crack growth rate of the as welded was decreased in comparison with that of the parents. (3) In fatigue test under cathodic protection, cathodic electric potential(-0.9V vs Ag/Agcl) for the SWS41 steel parent was effective, while for the as welded ineffective. (4) There was a tendency that the exponent(m) of the Paris' equation was decreased in order of microhardness magnititude in air and under cathodic protection conditions and vise versa in free corrosion. (5) Fracture surface has dimples and ductile striations in air test, but transgranular cracks and brittle striations under cathodic protection test.

• 대한조선학회논문집
• /
• 제36권4호
• /
• pp.137-146
• /
• 1999

선체구조는 많은 수의 구조부재로 이루어져 있으며, 구조물의 안정성을 확보하기 위해 모든 부위의 검사를 위해서는 경제적, 사회적인 많은 비용이 필요하므로, 검사시기 및 검사방법의 최적화는 선체구조의 안정성확보 및 경제적 관점에서 매우 중요한 부분이 되고 있다. 선체구조 손상중 많은 부분이 균열이며 이러한 미세한 균열이 성장하여 대규모 파괴로 진전되기 전에 검사를 통하여 균열을 검출하고 수리하는 과정을 Markov 연쇄모델에 의해 이상화 시켰으며, 검사 계획안의 최적화는 유전적 알고리즘을 통하여 구현하였다. 특히 선박은 부식환경하에서 운항하므로 부식에 의한 선체구조부재의 치수가 감소하기 때문에 응력이 변하고 균열진전의 확률적인 특성 또한 변한다. 정상 Markov 연쇄모델로서는 이러한 부식에 의한 영향을 고려할수 없기 때문에 비정상 Markov 연쇄모델에 의해 부식의 영향을 고려하였다. 여러개의 부재군에 대한 검사 계획안의 최적화에 대하여 수치계산을 실시하여 그 특성을 비교하였고, 부식영향하의 부재군에 대하여 검사기간중에 발생되는 고정비용의 정도에 따른 경제성 분석 및 목표 파괴확률의 정도에 따른 검사계획의 차이를 살펴보았다. 수치계산 예를 통하여 전체비용을 줄이기 위해서는 피로수명이 짧은 부재군에 대한 피로수명을 향상시키는 방안이 가장 효율적임을 알 수 있다.