• Steel and Composite Structures
• /
• 제50권3호
• /
• pp.337-345
• /
• 2024

This research proposed a particle swarm optimization (PSO) based seismic retrofit design of moment frame structures using a steel frame assembly. Two full scale specimens of the steel frame assembly with different corner details were attached to one-story RC frames for seismic retrofit, and the lateral load resisting capacities of the retrofitted frames subjected to cyclic loads were compared with those of a bare RC frame. The open source software framework Opensees was used to develop an analytical model for validating the experimental results. The developed analytical model and the optimization scheme were applied to a case study structure for economic seismic retrofit design, and its seismic performance was assessed before and after the retrofit. The results show that the developed steel frame assembly was effective in increasing seismic load resisting capability of the structure, and the PSO algorithm could be applied as convenient optimization tool for seismic retrofit design of structures.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제6권2호
• /
• pp.3-8
• /
• 2007

Nonlinear property and contact matter are analyzed about the pipe applied with internal pressure through this study. The weakest part and its safety can be examined. Maximum equivalent stress is shown at the contact surface between bolt and nut. The value of contact stress with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The maximum contact pressure is shown at the clamp corner of the external surface on pipe. The value of contact pressure with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The radial deformation with no pressure is also increased greatly at the middle part of internal surface on pipe. But this maximum deformation on pipe with the pressure of 12MPa is shown at the part far away the support of pipe. This value is increased 5.7 times as large as that value with no pressure. As contact status, the sticking occurs most at the external surface of pipe. It also tends to occur at the contact surface between bolt and nut. At the external surface of pipe, the sticking in case of the pressure of 12MPa occurs more than that in case of no pressure.

• KIPS Transactions on Software and Data Engineering
• /
• 제4권1호
• /
• pp.1-8
• /
• 2015

Safety critical systems require exhaustive verification of safety properties, because even a single corner-case fault can cause a critical safety failure. However, existing verification approaches are too costly in terms of time and computational resource required, making it hard to be applied in practice. In this paper, we implemented a tool for minimizing the size of the verification target w.r.t. verification properties to check, based on program slicing technique[1]. The efficacy of program slicing using our tool is demonstrated in a case study with a verification target Trampoline[3], which is an open source automotive operating system compliant with OSEK/VDX[2]. Experiments have shown enhanced performance in verification, with a 71% reduction in the size of the code.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.236-241
• /
• 2009

To identify turbulent flow characteristics of non-reacting case resulted from cooling flow injection in a rectangular swirl combustor, 3D Large Eddy Simulation(LES) was implemented and Proper Orthogonal Decomposition(POD) analysis was used for post-processing. The combustor of concern is the LM6000, lean premixed dry low-NOx annular combustor, developed by GEAE. It was observed that increase in speed of shear layer resulted from the inflow of cooling flow caused intensified vorticity magnitude in central toroidal recirculation zone. In the case of vorticity magnitude in corner recirculation zone, however, was weakened. In addition, pressure fluctuation in combustor was damped down and longitudinal acoustic mode was significantly dissipated

• Journal of Mechanical Science and Technology
• /
• 제18권2호
• /
• pp.313-324
• /
• 2004

A rich phenomenon in the dynamics of azimuthal vortices in a circular cylinder caused by the inertial oscillation is investigated numerically at high Reynolds numbers and moderate Rossby numbers. In the actual spin-up flow where both the Ekman circulation and the bottom friction effects are included, the first appearance of a seed vortex is generated by the Ekman boundary-layer on the bottom wall and the subsequent roll-up near the corner bounded by the side wall. The existence of the small vortex then rapidly propagates toward the inviscid region and induces a complicated pattern in the distribution of azimuthal vorticity, i.e. inertial oscillation. The inertial oscillation however does not deteriorate the classical Ekman-pumping model in the time scale larger than that of the oscillatory motion. Motions of single vortex and a pair of vortices are further investigated under a slip boundary-condition on the solid walls. For the case of single vortex, repeated change of the vorticity sign is observed together with typical propagation of inertial waves. For the case of a pair of vortices with a two-step profile in the initial azimuthal velocity, the vortices' movement toward the outer region is resisted by the crescent-shape vortices surrounding the pair. After touching the border between the core and outer regions, the pair vortices weaken very fast.

• Journal of the Korean Arthroscopy Society
• /
• 제10권2호
• /
• pp.184-186
• /
• 2006

Isolated lateral collateral ligament injury has been reported as avulsion fracture of attachment site or intrasubstance tear. The treatment of avulsion fracture of lateral collateral ligament was primary repair with anchor or staple. There are some reports about loosening or migration of staple which used in repairing meniscus of knee. There is, however, no report about loosening or migration of staple which was used for lateral collateral ligament repair. We report a case of migrated staple that was used for lateral collateral ligament repair, which was migrated to intraarticular posterolateral corner of the knee.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제29권6호
• /
• pp.543-547
• /
• 2007

The lips and corners of the mouth are not only important for appearance but are also essential for facial expression, speech, and nutrition. Defects in these areas can be caused by congenital clefts of the lip and face, trauma, infection, cysts, and excision of benign or malignant tumors. Numerous techniques have been introduced for reconstruction of the lips and corners of the mouth, and in particular, techniques such as the Kazanjian Roopenian I and II, Converse method, Zisser method, Platz and Wepner method. Gillies and Millard method are commonly utilized for elongation and reconstruction of the mouth corner. Few reports exist in the oral and maxillofacial surgery literature regarding correction of microsomia and reconstruction of the corners of the mouth. As such, the authors report a case of the corners of the mouth elongation in a patient with burn-induced microstomia using the Converse flap which yielded a satisfactory outcome.

• Magazine of the Korean Society of Agricultural Engineers
• /
• 제34권E호
• /
• pp.30-44
• /
• 1992

A modification of the TEACH-like computer program based on the k-$\varepsilon$ turbulence transport was applied for predicting air mixing patterns and temperature distributions in a rectangular, slot-ventilated enclosure having obstructions ; a rectangular obstacle with heat flux, solid walls separates the passage and the pig pens, and purlins beneath the ceiling. Air flow patterns were calculated for the cases with and without the purlin, extending 300mm beneath the ceiling. Comparisons of prediction data of Randall & Battams(1976) showed air flow pattern predicted well for the case without the purlin. Heat was accumulated at the corner of the left side of the solid wall and the right-upper region of the simulated pigs. However the air distribution pattern was completely different from data for the case with the purlin. The deviation from the observation may be attributed to the difference of the geometric configuation. Exploring the cause of the deviation should be conducted in a further study. Temperature stratification was also observed due to incomplete mixing. The obstruction in the route of the inlet air jet at inlet should be avoided since most of kinetic energy dissipates at the abstacle duet to impingement.

• Wind and Structures
• /
• 제11권1호
• /
• pp.1-18
• /
• 2008

Interference effects in five square tall buildings arranged in an L- or T-shaped pattern are investigated in the wind tunnel. Mean and fluctuating shear forces, overturning moments and torsional moment are measured on each building with a force balance mounted at its base. Results are obtained at two values of clear separation between adjacent buildings, at half and a quarter building breadth. It is found that strong interference effect exists on all member buildings, resulting in significant modifications of wind loads as compared with the isolated single building case. Sheltering effect is observed on wind loads acting along the direction of an arm of the "L" or "T" on the inner buildings. However, increase in these wind loads from the isolated single building case is found on the most upwind edge building in the arm when wind blows at a slight oblique angle to the arm. The corner formed by two arms of buildings results in some wind catchment effect leading to increased wind pressure on windward building faces. Interesting interference phenomena such as negative drag force are reported. Interference effects on wind load fluctuations, load spectra and dynamic building responses are also studied and discussed.

• Journal of Information Technology Applications and Management
• /
• 제28권3호
• /
• pp.23-30
• /
• 2021

Korea currently provides long-term care benefits for the elderly with poor functionality, but most of the service providers are private businesses. This is the time when quality management of care services is required, which is just around the corner of the super-aged era. In this study, we would like to look at the case in which 'A company', which operates a long-term care institution, attempted to make voluntary changes ahead of social demands. The company tried to transform the social needs of quality management by judging them as opportunities, not threats, and establishing an integrated database of centers. First, the company processed data and built a cloud-based database system. Second, the company automatically linked data from existing systems for the efficiency of data utilization. Third, the company pursued visualization for the convenience of data utilization. This allowed the company to make data-driven strategic decisions internally. This is expected to increase sales as it will soon lead to securing new customers and pioneering new markets. It is also significant in that it can provide best practices for the long-term care industry.