• 반도체디스플레이기술학회지
• /
• 제4권2호
• /
• pp.39-43
• /
• 2005

In the study, in order to deposit TaN thin film for diffusion barrier and bottom electrode we made the Plasma Assisted ALD equipment and confirmed the electrical characteristics of TaN thin films grown PAALD method. Plasma Assisted ALD equipment depositing TaN thin film using PEMAT(pentakis(ethylmethlyamino) tantalum) precursor and NH3 reaction gas is shown that TaN thin film deposited high density and amorphous phase with XRD measurement. The degree of diffusion and reaction taking place in Cu/TaN (deposited using 150W PAALD)/$SiO_{2}$/Si systems with increasing annealing temperature was estimated for MOS capacitor property and the $SiO_{2}$, (600${\AA}$)/Si system surface analysis by C-V measurement and secondary ion material spectrometer (SIMS) after Cu/TaN/$SiO_{2}$ (400 ${\AA}$) layer etching. TaN thin film deposited PAALD method diffusion barrier have a good diffusion barrier property up to 500$^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.162-165
• /
• 2003

The corrosion characteristics of diffusion barrier in Copper CMP has been investigated. Key experimental variables that has been investigated are the corrosion rate by different agents containing slurry of Cu CMP. Whenever Cu and Ta films were corroded adding each oxidizer, the corrosion rate of Ta was much lower than that of Cu. That is, the difference in the corrosion rates of Ta by oxidizer was not larger as compared with Cu. As corroded by complexing agents, the corrosion rate of Ta was close to O. The corrosion rate of Ta increased as added $HNO_3$ and $CH_3COOH$ compared with the reference slurry; on the other hand, it decreased with addition of HF. In addition, resulting corrosion rate went up with lower pH of agent. The corrosion rates by agents were however significant small; hence, it doesn't affect on the removal rate of Cu CMP practically. Consequently, this can be explained by assuming that the mechanical effect dominates than the chemical effect on the polishing rate of Ta(TaN).

• 한국진공학회지
• /
• 제9권3호
• /
• pp.267-272
• /
• 2000

electroplating(EP)법을 이용하여 ULSI용 Cu 박막을 제조하였다. seed Cu는 sputtering으로 증착하였으며, 확산방지막으로 TaN를 사용하였다. 제작된 EP Cu 박막은 seed Cu의 영향으로 열처리 조건에 관계없이 Cu(111)방향으로 강하게 우선 배향 하였다. 열처리 온도와 시간이 증가함에 따라 Cu박막의 미세조직이 non-columnar structure에서 약 2배 이상 결정립 성장하여 columnar structure로 바뀌었으며, 또한 as-deposit시 관찰되었던 stacking fault, twin, dislocation들이 상당히 줄어드는 것이 관찰되었다. Cu의 확산에 의하여 생기는 copper-silicide는 관찰할 수 없었으며, 이것은 두께 45nm의 TaN막이 $450^{\circ}C$, 30분 열처리시 확산방지막으로 충분한 역할을 한 것으로 판단된다. Cu(111)우선 배향과 열처리에 의한 결정립 성장 및 defect감소는 Cu 박막의 결정립계에서 발생하는 electromigration 현상을 상당히 줄일 수 있을 것으로 판단된다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.102-102
• /
• 2018

Electronic industry had required the finer size and the higher performance of the device. Therefore, 3-D die stacking technology such as TSV (through silicon via) and micro-bump had been used. Moreover, by the development of the 3-D die stacking technology, 3-D structure such as chip to chip (c2c) and chip to wafer (c2w) had become practicable. These technologies led to the appearance of HBM (high bandwidth memory). HBM was type of the memory, which is composed of several stacked layers of the memory chips. Each memory chips were connected by TSV and micro-bump. Thus, HBM had lower RC delay and higher performance of data processing than the conventional memory. Moreover, due to the development of the IT industry such as, AI (artificial intelligence), IOT (internet of things), and VR (virtual reality), the lower pitch size and the higher density were required to micro-electronics. Particularly, to obtain the fine pitch, some of the method such as copper pillar, nickel diffusion barrier, and tin-silver or tin-silver-copper based bump had been utillized. TCB (thermal compression bonding) and reflow process (thermal aging) were conventional method to bond between tin-silver or tin-silver-copper caps in the temperature range of 200 to 300 degrees. However, because of tin overflow which caused by higher operating temperature than melting point of Tin ($232^{\circ}C$), there would be the danger of bump bridge failure in fine-pitch bonding. Furthermore, regulating the phase of IMC (intermetallic compound) which was located between nickel diffusion barrier and bump, had a lot of problems. For example, an excess of kirkendall void which provides site of brittle fracture occurs at IMC layer after reflow process. The essential solution to reduce the difficulty of bump bonding process is copper to copper direct bonding below $300^{\circ}C$. In this study, in order to improve the problem of bump bonding process, copper to copper direct bonding was performed below $300^{\circ}C$. The driving force of bonding was the self-annealing properties of electrodeposited Cu with high defect density. The self-annealing property originated in high defect density and non-equilibrium grain boundaries at the triple junction. The electrodeposited Cu at high current density and low bath temperature was fabricated by electroplating on copper deposited silicon wafer. The copper-copper bonding experiments was conducted using thermal pressing machine. The condition of investigation such as thermal parameter and pressure parameter were varied to acquire proper bonded specimens. The bonded interface was characterized by SEM (scanning electron microscope) and OM (optical microscope). The density of grain boundary and defects were examined by TEM (transmission electron microscopy).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.409-409
• /
• 2013

최근, 집적 소자의 미세화에 따라 늘어난 배선 신호 지연 및 상호 간섭, 그리고 소비 전력의 증가는 초고집적 소자 성능 개선에 한계를 가져온다. 이에 따라 기존의 알루미늄(Al)/실리콘 절연 산화막은 구리(Cu)/저유전율 박막(low-k)으로 대체되고 있고, 이는 소자 성능 개선에 큰 영향을 미친다. 그러나 Cu는 Si과 low-k 내부로 확산이 빠르게 일어나 소자의 비저항을 높이고, 누설 전류를 일으키는 등 소자의 성능을 저하시킬 수 있는 문제점을 가지고 있다. 이러한 Cu의 확산을 막기 위하여 Ta, TaN 등과 같은 확산방지막에 대한 연구가 활발히 진행되어 왔으나, 배선 공정의 집적화와 low-k 대체에 따른 공정 및 신뢰성 문제로 인해 새로운 확산방지막의 개발이 필요하게 되었다. 이를 위해, 본 연구에서는 Cu-V 합금을 사용하여 low-k 기판 위에 확산방지막을 자가 형성 시키는 공정에 대한 연구를 진행하였다. 다양한 low-k 기판에서 열처리조건에 따른 Cu-V 합금의 특성을 확인하기 위해 4-point probe를 통한 비저항 평가와 XRD (X-ray diffraction) 분석이 이뤄졌다. 또한, TEM (transmission electron microscope)을 이용하여 $300^{\circ}C$에서 1 시간 동안 열처리를 거쳐 자가형성된 V-based interlayer가 low-k와 Cu의 계면에서 균일하게 형성된 것을 확인하였다. 형성된 V-based interlayer의 barrier 특성을 평가하고자 Cu-V합금/low-k/Si 구조와 Cu/low-k/Si 구조의 leakage current를 비교 분석하였다. Cu/low-k/Si 구조는 비교적 낮은 온도에서 leakage current가 급격히 증가하는 양상을 보였으나, Cu-V 합금/low-k/Si 구조는 $550^{\circ}C$의 thermal stress 에서도 leakage current의 변화가 거의 없었다. 이러한 결과를 바탕으로 열처리를 통해 자가형성된 V-based interlayer의 Cu/low-k 간 확산방지막으로서 가능성을 검증하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.260-260
• /
• 2009

In high-efficiency crystalline silicon solar cell, If high-efficiency solar cells are to be commercialized, It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper are applied widely in various electronic manufactures as easily formation is available by plating. Ni is shown to be a suitable barrier to Cu diffusin as well as desirable contact metal to silicon. Nickel monosilicide has been suggested as a suitable silicide due to its lower resistivitym lower sintering temperature and lower layer stress than $TiSi_2$. In this paper, Nickel as a seed layer and diffusion barrier is plated by electroless plating to make nickel monosilicide.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.683-690
• /
• 1996

In this study, the diffusion barrier properties of $1000 \AA$ thick molybdenum compounds (Mo, Mo-N, $MoSi_2$, Mo-Si-N) were investigated using sheet resistance measurements, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning electron microscopy (SEM), and Rutherford backscattering spectrometry (RBS). Each barrier material was deposited by the dc magnetron sputtering, and annealed at 300-$800^{\circ}C$ for 30min in vacuum. Mo and $MoSi_2$ barrier were failed at low temperature due to Cu diffusion through grain bound-aries and defects of Mo thin film and the reaction of Cu with Si within $MoSi_2$ respectively. A failure temperature could be raised to $650^{\circ}C$-30min in the Mo barrier system and to $700^{\circ}C$-30min in the Mo-silicide system by replacing Mo and $MoSi_2$ with Mo-N and Mo-Si-N, respectively. The crystallization temperature in the Mo-silicide film was raised by the addition of $N_2$. It is considered that not only the N, stuffing effect but also the variation of crystallization temperature affects the reaction of Cu with Si within Mo-silicide. It was found that Mo-Si-N is more effective barrier than Mo, $MoSi_2$, or Mo-N to copper penetration preventing Cu reaction with the substrate for 30min at a temperature higher than $650^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.9-11
• /
• 2001

차세대 고속 DRAM기술에 사용될 금속인 Cu의 확산 방지막(diffusion harrier) 물질로는 Ta 또는 W 같은 Refractory metal 이 융점(melting point)이 높고 저항값이 낮아 많이 연구 보고되고 있으나, 본 논문에서는 초고주파 소자에서 Au의 확산 방지 막으로 많이 사용되고 있으며. 선택적 증착이 용이한 Pt과 Ni를 MOS 소자의 Cu 확산 방지 막으로 적용하며 어닐링한 후 소자의 게이트 산화막 누설전류($I_{leak}$), 그리고. Si/$SiO_2$ 계면의 trap density 등의 변이를 측정하여 Cu가 소자의 특성 열화에 미치는 영향을 연구하였다. 실험 결과 Pt/Ti($200{\AA}/100{\AA}$)를 적용한 경우 소자 측성 열화가 가장 적었으며. 이는 Copper의 확산 방지막으로 Pt/Ti를 사용하여 전기적 특성 및 계면 특성을 개선시킬 수 있음을 보여 주었다. 이는 SIMS Profile을 통해서도 확인하였다.

• 한국재료학회지
• /
• 제6권6호
• /
• pp.626-631
• /
• 1996

Reactive dc magnetron sputtering 법을 이용하여 증착한 molybdenum mitride 박막의 Cu 확산 방지막 특성을 조사하였다. Cu 확산 방지막으로서 molybdenum nitride 박막의 열적안정성을 관찰하기 위하여 molybdenum nitride 박막 위에 Cu를 evaporation 법으로 증착하고 진공 열처리하였다. Cu/r-Mo2N/si 구조는 $600^{\circ}C$, 30분간 열처리 시까지 안정하였다. 확산 방지막의 파괴는 $650^{\circ}C$, 30분간 열처리 시부터 격자 확산(lattice diffusion)이나 입계(grain boundary)과 결함(defect)을 통한 확산에 의해 나타나기 시작하였고, 이 때 molybdenum silicide과 copper silicide의 형성에 기인된 것으로 생각되었다. 열처리 이후 Cu/r-Mo2N/Si 사이의 상호반응이 증가하였다. 이는 Rutherford backscattering spectrometry, Auger electron spectroscopy 그리고 Nomarski microscopy 등의 분석을 통해 조사되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.352.2-352.2
• /
• 2014

In this present work, we report a Cu-Mn alloy as a materials for the self-forming barrier process. And we investigated diffusion barrier properties of self-formed layer on low-k dielectrics with or without UV curing treatment. Cu alloy films were directly deposited onto low-k dielectrics by co-sputtering, followed by annealing at various temperatures. X-ray diffraction revealed Cu (111), Cu (200) and Cu (220) peaks for both of Cu alloys. The self-formed layers were investigated by transmission electron microscopy. In order to compare barrier properties between Mn-based interlayer interlayer, thermal stability was measured with various low-k dielectrics. X-ray photoelectron spectroscopy analysis showed that chemical compositions of self-formed layer. The compositions of the Mn based self-formed barriers after annealing were determined by the C concentration in the dielectric layers.