• Geophysics and Geophysical Exploration
• /
• v.26 no.3
• /
• pp.103-113
• /
• 2023

In the oil and gas exploration market, various cableless seismic systems have been developed as an alternative to improve data acquisition efficiency. However, developing such equipment at a small scale for academic research is not available owing to highly priced commercial products. Fortunately, building and experimenting with open-source hardware enable the academic utilization of cableless seismic equipment with relatively low cost. This study aims to develop a cableless seismic acquisition module using Arduino. A cableless seismic system requires the combination of signal sensing, simple pre-processing, and data storage in a single device. A conventional geophone is used as the sensor that detects the seismic wave signal. In addition, it is connected to an Arduino circuit that plays a role in implementing the processing and storing module for the detected signals. Three main functions are implemented in the Arduino module: preprocessing, A/D conversion, and data storage. The developed single-channel module can acquire a common receiver gather from multiple source experiments.

• Korean Journal of Optics and Photonics
• /
• v.17 no.6
• /
• pp.537-543
• /
• 2006

A method of estimating the distance using single zoom camera limits a distance range(only optical axis) in field of view. So, in this paper, we propose a method of estimating the distance information in Stereoscopic display using the stereo zoom lens module for estimating the distance in the wide range. The binocular stereo zoom lens system is composed using a horizontal moving camera module. The left and right images are acquired in polarized stereo monitor for getting the conversion and estimating a distance. The error distance is under 10mm which has difference between optically a traced distance and an estimated distance in left and right range $(0mm{\sim}500mm)$ at center. This presents the system using a function of the zoom and conversion has more precise distance information than that of conversion control. Also, a method of estimating a distance from horizontal moving camera is more precise value than that from toe-in camera by comparing the error distance of the two camera methods.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.1
• /
• pp.39-45
• /
• 2011

In this paper, the design method of portable signal analysis system is proposed and the hardware module is implemented for operation of base stations based on a common platform for mobile WiMax. The new signal analysis method is implemented as two modules; a broadband RF module and a DSP based digital signal analysis module. The RF module performs the RF-IF down conversion and gain control. And the digital module measure the base staion signal. The differences of performance are insignificant in the experiment results performed through the comparison of other fixed-large system and proposed system.

• Current Photovoltaic Research
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2022

Bifacial photovoltaic (PV) technology has received considerable attention in recent years due to the potential to achieve a higher annual energy yield compared to its monofacial PV systems. In this study, we fabricated the bifacial c-Si PV module with a shingled design using the conventional patterned bifacial solar cells. The shingled design PV module has recently attracted attention as a high-power module. Compared to the conventional module, it can have a much more active area due to the busbar-free structure. We employed the transparent backsheet for a light reception at the rear side of the PV module. Finally, we achieved a conversion power of 453.9 W for a 1300 mm × 2000 mm area. Moreover, we perform reliability tests to verify the durability of our Shingled Design Bifacial c-Si Photovoltaic module.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.636-640
• /
• 2000

A novel integrated battery charger/discharger converter for a standardized battery module is proposed. Instead of using separate charger and discharger converters. it integrates these two converters into a single converter in order to minimize the size. the integrated charger/discharger converter not only regulates the solar array output power including the peak power tracking capability but also controls the battery charging/discharging current depending on the solar array output power and the load power. In addition it offers a regulated bus voltage which simplifies the power distribution/conversion for the pay load.

• Journal of information and communication convergence engineering
• /
• v.6 no.3
• /
• pp.266-269
• /
• 2008

Layered structure of the Korean terrestrial Digital Multimedia Broadcasting (TDMB) transmission system for multimedia broadcasting service is presented in this paper. We made a switching module which is called the Ensemble Remultiplexer. It is designed to remultiplex the Ensemble Transport Interface (ETI) for T-DMB service. This paper describes the remultiplexing process of the Ensemble Remultiplexer.

• Journal of information and communication convergence engineering
• /
• v.5 no.4
• /
• pp.358-361
• /
• 2007

We report on a new type dc-dc converter design that combines the advantage of dc ripple noise elimination and high efficiency. As potential low cost solar cells, DSC module and the panel's system efficiency and stability are still critical problems to the way of marketing. In this study, a new three-step dc-dc converter scheme with the phase-shift-carrier technology is proposed to apply for solar power system. We have achieved power conversion efficiency around 94.88%.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.269-274
• /
• 1999

This paper aims to DNC application of car fuel tank die working. DNC system is consist of CAD, CAM software and CNC milling machine. CAM software is purpose to G-code generation for CNC programming. Then CAM software and CNC milling machine are connect to RS-232-C cable for networking.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.63-64
• /
• 2016

This paper deal with single module design of 13.2kVrms/10kVA solid state transformers exchanging conventional transformer. We can design compact hardware system to reduce size and get higher switching frequency by using SiC devices. As a result by comparing simulation results with experiment result, it is verified.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.11a
• /
• pp.184-185
• /
• 2002

We discussed the main issues of 10GHz Receiver packaging. High frequency structure simulations and circuit simulations for TO-CANs led to a new design for 10GHz optical receiver module packaging. The simulation results were compared to the measured laboratory data. The proposed package has low cost and easy manufacture process far mass production. Using this package, we had a good optical to electrical conversion (OE) characteristic at a data rate of 10Gbps.