• The korean journal of orthodontics
• /
• v.42 no.1
• /
• pp.17-22
• /
• 2012

Objective: To study and compare the effects of different demineralization-inhibition methods on the shear bond strength (SBS) and fracture mode of an adhesive used to bond orthodontic brackets to demineralized enamel surfaces. Methods: Eighty freshly extracted, human maxillary premolars were divided into 4 equal groups and demineralized over the course of 21 days. Brackets were bonded to the demineralized enamel of teeth in Group 1. In Group 2, bonding was performed following resin infiltration ($ICON^{(R)}$, DMG, Hamburg, Germany). Before bonding, pre-treatment with acidulated phosphate fluoride (APF) or solutions containing casein phosphopeptide-amorphous calcium phosphate with 2% neutral sodium fluoride (CPP-ACP/wF) was performed in Groups 3 and 4, respectively. The SBS values of the brackets were measured and recorded following mechanical shearing of the bracket from the tooth surface. The adhesive remnant index (ARI) scores were determined aft er the brackets failed. Statistical comparisons were performed using one-way ANOVA, Tukey's post-tests, and G-tests. Results: Significant differences were found in some of the intergroup comparisons of the SBS values (F = 39.287, p < 0.001). No significant differences were found between the values for the APF-gel and control groups, whereas significantly higher SBS values were recorded for the resin-infiltrated and CPP-ACP/wF-treated groups. The ARI scores were also significantly different among the 4 groups (p < 0.001). Conclusions: Tooth surfaces exposed to resin infiltration and CPP-ACP/wF application showed higher debonding forces than the untreated, demineralized surfaces.

• Strategy21
• /
• s.41
• /
• pp.294-332
• /
• 2017

The aim of this study is to find ways to apply the strategic communications to the Republic of Korea Navy. It may be a little bit late for the ROK Navy to accommodate the SC in these days because the adoption and implementation of the SC by the Combined Forces Command has already been begun. It was in 2007 when the SC was in place in the CFC. ROK's Ministry of National Defense and Joint Chiefs of Staff have also mulled over the SC and begun to apply it in part in the annual exercises such as Key Resolve command post drills and Foal Eagle field training exercise, etc. For the ROK Navy, in addition to those exercises, it is faced with further areas like North Korean maritime provocations and other maritime incidents where its version of SC is needed. As noted, the SC is not intended to deter or defend directly those provocations and incidents, but aims to create conditions favorable to the achievement of the navy's strategic objectives. The ROK Navy has to establish a SC planning center and implementing organizations within the Headquarters to be consistent with its above organizations such as MND, JCS, and CFC that have already applied the SC in part or in entirety. SC center and other related organizations need to be under the control of VCNO and the center needs to be located and administered by the policy division in N-5 at the HQs. The vision of the navy's SC is the winning without combats and the least damages in time of war. In other for the navy to reach the vision, the strategies to be executed are early establishment of SC implementing organizations, forming consensus over the need for the SC within the navy, strengthening core competencies to apply the SC, acquiring the SC experts and making doctrines on the SC. The SC, in addition, in the navy has to be planned and implemented in not only peace time and crisis time but also war time.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.4
• /
• pp.29-36
• /
• 2010

To investigate the cyclic characteristics of exterior joints in RC frame buildings which are typically used after 1988, 70% scaled T-shaped beam-column subassemblies were designed and tested with a displacement control that is composed of 9 steps, until 3.5% story drift was reached. Axial forces are applied to columns during the experiment to simulate a real situation. The results show that the non-seismic detailed specimens failed before reaching 0.85% story drift, and their strengths are less than 0.85 times the nominal flexural strength which beam or columns should reach. The relationship of principal stress and story drift of exterior joints is similar to the one that Priestly proposed.

• Journal of Periodontal and Implant Science
• /
• v.24 no.3
• /
• pp.649-660
• /
• 1994

The purpose of this study was to evaluate the effects of administration of Zea Mays L. on the healing process after periodontal surgery as adjuntives. Authors used 3 kinds of different clinical criteria, depth of periodontal pocket by using the Goldman Fox periodontal probe, degree, of tooth mobility by Periotest, and amount of occlusal force with electronic device. In this comparative clinical study, 30 patients who were divided into two group, 15 ZML administrated group and 15 placebo adminstrated group, were participated. All the examined teeth were isolated with gauze and air spray, and measured each clinical critera on the day of before surgery, 1, 2, 4, 8 weeks after surgery. The results were as follows. 1. The changes of the periodontal pocket depth, on the both of Zea Mays L. administrated group and placebo adminstrated group, revealed the decreasing tendency, and it was shown the time dependent tendency. But there was no statistically significant differences between the two group. 2. In the case of tooth mobility, both group showed the highest severe mobility on the 1 week after surgery. It was observed that experimental group had more effects on decreasing the mobility. But there was no statistically significant differences between the two group. 3. In the case of experimental group, the recovery trend of occlusal forces after periodontal surgery on the molar teeth revealed higher than the control group. But there was no statistically significant differences between the two group. In conclusion, Zea Mays L. may play a favorable role in the healing process after periodontal surgery. It was suggested that further study to evaluate the effects of selective administration on the patient who have systemic diseases should be needed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.353-359
• /
• 2017

The classical computer numerical control (CNC) machine is widely used for mold making in various industries. However, while improving the process, it has a negative effect on production quality and worker safety. As a result, the complaints of workers have increased and production quality has decreased. Therefore, we found optimizing cutting conditions to mold industrials for cutting conditions commonly used. However, the problem is the insert tool geometric modeling. In this study, the modeling of an insert tool was performed using the Solidworks program. The insert tool model was imported into the analysis application AdvantEdge, which predicted cutting forces, tool stress, and temperature.

• Wind and Structures
• /
• v.23 no.2
• /
• pp.143-155
• /
• 2016

The interaction between two different shaped structures is very important to be understood. Fluid-structure interactions and aerodynamics of a circular cylinder in the wake of a V-shaped cylinder are examined experimentally, including forces, shedding frequencies, lock-in process, etc., with the V-shaped cylinder width d varying from d/D = 0.6 to 2, where D is the circular cylinder diameter. While the streamwise separation between the circular cylinder and V-shaped cylinder was 10D fixed, the transverse distance T between them was varied from T/D = 0 to 1.5. While fluid force and shedding frequency of the circular cylinder were measured using a load cell installed in the circular cylinder, measurement of shedding frequency of the V-shaped cylinder was done by a hotwire. The major findings are: (i) a larger d begets a larger velocity deficit in the wake; (ii) with increase in d/D, the lock-in between the shedding from the two cylinders is centered at d/D = 1.1, occurring at $d/D{\approx}0.95-1.35$ depending on T/D; (iii) at a given T/D, when d/D is increased, the fluctuating lift grows and reaches a maximum before decaying; the d/D corresponding to the maximum fluctuating lift is dependent on T/D, and the relationship between them is linear, expressed as $d/D=1.2+{\frac{1}{e}}T/D$; that is, a larger d/D corresponds to a greater T/D for the maximum fluctuating lift.

• Wind and Structures
• /
• v.23 no.2
• /
• pp.109-125
• /
• 2016

Flow interference is investigated between two tripped cylinders of identical diameter D at stagger angle ${\alpha}=0^{\circ}{\sim}180^{\circ}$ and gap spacing ratio $P^*$ (= P/D) = 0.1 ~ 5, where ${\alpha}$ is the angle between the freestream velocity and the line connecting the cylinder centers, and P is the gap width between the cylinders. Two tripwires, each of diameter 0.1D, were attached on each cylinder at azimuthal angle ${\beta}={\pm}30^{\circ}$, respectively. Time-mean drag coefficient ($C_D$) and fluctuating drag ($C_{Df}$) and lift ($C_{Lf}$) coefficients on the two tripped cylinders were measured and compared with those on plain cylinders. We also conducted surface pressure measurements to assimilate the fluid dynamics around the cylinders. $C_D$, $C_{Df}$ and $C_{Lf}$ all for the plain cylinders are strong function of ${\alpha}$ and $P^*$ due to strong mutual interference between the cylinders, connected to six interactions (Alam and Meyer 2011), namely boundary layer and cylinder, shear-layer/wake and cylinder, shear layer and shear layer, vortex and cylinder, vortex and shear layer, and vortex and vortex interactions. $C_D$, $C_{Df}$ and $C_{Lf}$ are very large for vortex and cylinder, vortex and shear layer, and vortex and vortex interactions, i.e., the interactions where vortex is involved. On the other hand, the interference as well as the strong interactions involving vortices is suppressed for the tripped cylinders, resulting in insignificant variations in $C_D$, $C_{Df}$ and $C_{Lf}$ with ${\alpha}$ and $P^*$. In most of the (${\alpha}$, $P^*$ ) region, the suppressions in $C_D$, $C_{Df}$ and $C_{Lf}$ are about 58%, 65% and 85%, respectively, with maximum suppressions 60%, 80% and 90%.

• Steel and Composite Structures
• /
• v.33 no.6
• /
• pp.891-906
• /
• 2019

This study considers the instability behavior of sandwich plates considering magnetorheological (MR) fluid core and piezoelectric reinforced facesheets. As facesheets at the top and bottom of structure have piezoelectric properties they are subjected to 3D electric field therefore they can be used as actuator and sensor, respectively and in order to control the vibration responses and loss factor of the structure a proportional-derivative (PD) controller is applied. Furthermore, Halpin-Tsai model is used to determine the material properties of facesheets which are reinforced by graphene platelets (GPLs). Moreover, because the core has magnetic property, it is exposed to magnetic field. In addition, Kelvin-Voigt theory is applied to calculate the structural damping of the piezoelectric layers. In order to consider environmental forces applied to structure, the visco-Pasternak model is assumed. In order to consider the mechanical behavior of structure, sinusoidal shear deformation theory (SSDT) is assumed and Hamilton's principle according to piezoelasticity theory is employed to calculate motion equations and these equations are solved based on differential cubature method (DCM) to obtain the vibration and modal loss factor of the structure subsequently. The effect of different factors such as GPLs distribution, dimensions of structure, electro-magnetic field, damping of structure, viscoelastic environment and boundary conditions of the structure on the vibration and loss factor of the system are considered. In order to indicate the accuracy of the obtained results, the results are validated with other published work. It is concluded from results that exposing magnetic field to the MR fluid core has positive effect on the behavior of the system.

• Science of Emotion and Sensibility
• /
• v.7 no.1
• /
• pp.1-7
• /
• 2004

This study aims to validate the effectiveness of CAVE system with an Arm-Master in the evaluation of virtual prototypes. A virtual kitchen with a refrigerator was presented in the CAVE system. Subjects put in and pull out virtual objects by using the Arm-Master. Twelve subjects, six males and six females, participated in the six experimental conditions : three types of refrigerator door grips and two reaction forces. After each trial, subjects evaluated a door grip of the virtual refrigerator in terms of easiness of operation, similarity in force, presence etc. The results show the mean values of vortical-type door grips are greater than the horizontal pocket-type door grip. Also the subjects preferred 5N in the reaction force of the Arm-Master rather than 15 N when they open and close virtual door. Unexpectedly, female subjects significantly marked low scores in the evaluation terms compared ruth mali subjects. It explains the Arm-Master should be modified much more if it works effectively in design evaluation.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.3
• /
• pp.324-333
• /
• 2012

The conventional medium and large caliber gun, in general, utilize the hydro-pneumatic recoil mechanism to control the firing impulse and to return to the battery position. However, this kind of mechanism may cause the problems like the leakages and the property changes in oil and gas due to the temperature variations between low and high temperatures. Accordingly, the friction spring mechanism has recently been researched as an alternative system. The friction spring mechanism consists of a set of closed inner and outer rings with the concentric tapered contact surfaces assembled in the columnar form, and can only be used under the compression load. When the spring column is axially loaded, the tapered surfaces become overlapped, causing the outer rings to expand while the inner rings are being contracted in diameter allowing an axial displacement. Because of friction between tapered contact surfaces, much higher spring stiffness is obtained on the stroke at the increase in load than the stroke at the decrease. In this paper, the dynamic equations regarding the friction spring system and the design approach have been investigated. It is also tried for a dynamic model representing the recoil motion and the friction spring forces. And the model has been proved from firing test using a gun system with friction springs. All the results show that the recoil mechanism using friction springs can substitute for the classic hydro-pneumatic recoil system.