• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.970-970
• /
• 2012

최근 치수의 기능을 수행하면서 원래 자연하천의 모습을 보전 혹은 복원하는 "생태하천 복원 공법"의 필요성이 대두되고 있으나 구체적인 공법에 대한 연구는 미미한 실정이다. 본 연구에서는 하천 내 시설물의 조성 시 유황에 따른 자연 하안 유도와 습지형태의 생물 서식공간 조성 유무를 평가하기 위하여 평창강 일원에 목재 유도틀을 설치하고 이에 따른 지형변화, 저서무척추동물을 포함한 수생생물들의 서식특성을 분석하였다. 평창강 금당계곡 일원을 대상으로 RMA-2 모형의 범용프로그램인 SMS 모형을 통해 수리 특성분석을 실시하였고 안산에 있는 수리모형 실험장에서 기본 수리특성 실험 후 수리적 안정성이 확보된 지점에 목재 유도틀을 2009년 9월에 설치하여 유도틀 설치 전과 설치 후 2010년 10월까지의 지형변화를 분석하였다. 지형의 측량은 광파측정기(니콘 DTM-520)로 하였으며 측량된 자료를 이용하여 Contour Map을 작성하여 지형변화를 분석하였고, 유도틀 설치지역을 중심으로 2010년에 3차에 걸쳐 지형 및 생물상 변화에 대한 정량 및 정성조사를 실시하여 비교분석 하였다. 유도틀 설치 후 2010년 하절기에 집중호우에 의한 유도틀의 파손 및 형태변형 등 문제가 없어 수리적으로 안정한 것으로 판단되었다. 지형 변화의 측면에서는 유도틀 조성 전 사질로 되어있던 단순한 선형의 하안이 유도틀 설치 후 다양한 하상재질 및 형태가 변화했으며 유도틀의 배치에 따라서 굼치 및 둠벙형 습지가 형성되었다. 유도틀 설치지역의 3개지점(상부, 중간배후습지, 하부)에서 저서무척추동물에 대하여 모니터링한 결과, 설치된 유도틀의 중간지점에서 가장 높게 종의 서식이 확인되었으며 상부지점과 하부지점은 상대적으로 낮게 나왔으나 상부지점 보다는 하부지점이 양호하게 나타났다. 조사시기별 개체수의 변화에서는 종수변화와 패턴이 유사하게 나타났으며 깔다구와 꼬마줄날도래등 특정종의 증식이 많았다. 또한, 굼치 및 둠벙형 습지 내에 어류의 치어 및 유어, 양서류, 파충류등 다양한 생물의 서식이 확인되었다. 이는 유도틀에 의해 생성 및 유도된 지형변화가 하천을 기반으로 생활하는 생물들에게 다양한 피난처 및 은신처 역할을 잘 제공하고 있음을 보여준다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.6
• /
• pp.62-73
• /
• 2022

This research proposes a method to control combustion instability in a gas turbine combustor having an annular combustor form and compares the effect of flow symmetric braking through nozzle arrangement and the corresponding change in equivalent ratio. To this end, the symmetry breaking effect was confirmed through mode analysis of FFT, Time signal, and phase trajectory. In addition, the unstable area and the stable area were identified through mode analysis, and this was shown on the contour map. The present research shows that instability occurs when the equivalent ratio and the arrangement of the nozzles are symmetry or when the nozzles are continuously arranged, but if the arrangement and equivalent ratio are not symmetry, the combustion instability decreases dramatically even if the difference in the equivalent ratio is small.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.2
• /
• pp.240-248
• /
• 2024

The purpose of this study is to investigate the freezing phenomena in printed circuit heat exchanger (PCHE) for cryogenic liquid hydrogen vaporizer. Local freezing phenomena in hot channels should be avoided in designing PCHE for cryogenic liquid hydrogen vaporizer. Hence, the flow and thermal characteristics of PCHE is experimentally investigated to figure out the conditions under when freezing occurs. To conduct lab-scale PCHE experiment, liquid nitrogen is used as a working fluid in cold channels instead of using liquid hydrogen. Glycol water is used as a working fluid in hot channels. Based on the experimental data, ratio between mass flow rates of cold channels and that of hot channels is proposed as contour map to avoid the freezing phenomena in PCHE.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.1 no.1
• /
• pp.69-77
• /
• 1997

An intensity survey on the 13 December 1996 Yeogweol earthquake has mode for 262 locations throughout southern part of Korean peninsula, then we investigated attenuation properties in the south Korean region as well as intensities distribution. In this study, intensities are estimated to be from II to possibly VIII. The iso-seismal intensity map we obtained shows general pattern of intensity distribution in the south korean region quite clearly despite the inherent uncertainties included in the process of intensity estimation. In case of intensity larger than VI, considerable damages such as fracturing walls are frequently reported. One of the significant feature of this intensity map is, considering its magnitude 4.5 reported by KMA, the felt area is unusually large covering most of the Korean Peninsular except Cheju island. This result indicates either the magnitude is under estimated or the focal depth is much deeper than expected. Assuming indicates either the magnitude is under estimated or the focal depth is much deeper than expected. Assuming shallow earthquake whose focal depth is by iso-seismal contour lines for intensity IV to VII, respectively. To resolve this ambiguity, more reliable estimation of focal depth and magnitude by using telesesmic instrumental records should be made in the future.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.22 no.1
• /
• pp.21-27
• /
• 2004

It will be a real good news fer the people who were lost their hometown by the construction of a large dam to be restored to the farmer state. Focused on Cheung-pyung around where most part were submerged by the Chungju large Dam founded in eurly 1980s, It used remote sensing image restoration Technique in this study in order to restore topographical features before the flood with stereo effects. We gathered comparatively good satellite photos and remotely sensed digital images, then its made a new fusion image from these various satellite images and the topographical map which had been made before the water filled by the DAM. This task was putting together two kinds of different timed images. And then, we generated DEM including the outskirts of that area as matching current contour lines with the map. That could be a perfect 3D image of test areas around before when it had been water filled by making perspective images from all directions included north, south, east and west, fer showing there in 3 dimensions. Also, for close range visiting made of flying simulation can bring to experience their real space at that time. As a result of this experimental task, it made of new fusion images and 3-D perspective images and simulation live images by remotely sensed photos and images, old paper maps about vanished submerged Dam areas and gained of possibility 3-D terrain image restoration about submerged area by large Dam construction.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.6
• /
• pp.51-59
• /
• 2014

Shallow landslides and debris flows are a common form of soil slope instability in South Korea. These events may be generally initiated as a result of intense rainfall or lengthening rainfall duration because of the effects of climate change. This paper presents the evaluation of rainfall-induced natural soil slope stability and reinforced soil slope instability under vertical load (railway or highway load) throughout South Korea based on quantitative analysis obtained from 58 sites rainfall observatories for 38 years. The slope stability was performed for infinite and geogrid-reinforced soil slopes by taking an average of maximum rainfall every ten years from 1973 to 2010. Seepage analysis is carried out on unsaturated soil slope using the maximum rainfall at each site, and then the factor of safety was calculated by coupled analysis using saturated and unsaturated strength parameters. The contour map of South Korea shows four stages in 10-year-time for the degree of landslide hazard. The safety factor map based on long term observational data will help prevent rainfall-induced soil slope instability for appropriate design of geotechnical structures regarding disaster protection.

• Journal of Korean Society of Forest Science
• /
• v.81 no.1
• /
• pp.40-52
• /
• 1992

The use of meteorological information is essential in the industrial society. More specialized weather services are required to perform better industrial activities including forestry. A topoclimatological technique, in this study, which makes use of empirical relationships between the topography and the weather in Cheju Island was applied to produce reasonable estimates of monthly air temperatures over remote land area where routine observations are rare. Altitude values of the 250m grid points were first read from a 1 : 25000 topographic map. The mean altitude and other valuable topographical variables were then determined for each $1km^2$ land area. Daily minimum, maximum and mean air temperature data were collected from 19 points in Cheju Island from June 1987 to September 1988. The data were analyzed and grouped into 36 sets by type of air temperature and by month. Each of data set was regressed to the topographical variables to delineate empirical relationships between the local air temperature and the site topography. The total of 36 regression equations were finally selected and the equations were used to calculate the monthly air temperature for each $1km^2$ land area. The outputs were presented in a fine-mesh grid map with a 6-level contour capability.

• Food Science and Preservation
• /
• v.12 no.6
• /
• pp.617-623
• /
• 2005

Response surface methodology (RSM) was applied to microwave-assisted process (MAP) extraction for effective components from Mosla dianthera M. Microwave power (2,450 MHz, 0-160 W) and extraction time (1-5 min) were used as independent variables ($X_i$) for central composite design to yield 10 different extraction conditions. Optimum conditions were predicted for dependent variables of $75\%$ ethanol extracts, such as total yield($Y_1$), total phenolics($Y_2$), total flavonoids($Y_3$), and electron donation ability($Y_4$, EDA). Determination coefficients ($R^2$) of regression equations for dependent variables ranged from 0.8397 to 0.9801, and microwave power was observed to be more influential than extraction time in MAP. The maximal values of each dependent variable predicted at different extraction conditions of microwave power (W) and extraction time (min) were as follows; $6.76\%$ of total yield at 142.00 W and 4.36 min, 78.68 mg/g of total phenolics at 136.78 W and 4.40 min, 6.75 mg/g of total flavonoids at 159,69 W and 3.17 min, and $49.81\%$ of EDA at 133.87 W and 4.47 min, respectively. The superimposed contour maps for maximizing dependent variables illustrated the MAP conditions of 79 to 113 W in power and of 2.73 to 3.84 min in extraction time.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.4
• /
• pp.557-566
• /
• 2005

In preparation of steamed foam-cakes, effects of whipping time, amount of wheat flour, and amounts of emulsifier on physical properties of the steamed foam cakes were investigated using RSM (response surface methodology). The three independent variables selected for the RSM experiment were whipping time $(X_1)$, amount of wheat flour $(X_2)$, and amounts of wheat flour $(X_2)$, and concentration of emulsifier $(X_3)$ were set for single-stage mixing, respectively. A rotatable central composite design was used for treatment arrangement. The responses from the product for loaf volume, color values and textural properties were analysed. In the analysis of variance for the foam cakes prepared by single-stage method, significant interactions were observed between independent variables (experimental factors) and physical property like loaf volume (p<0.05); textural properties like hardness, gumminess, and chewiness (p<0.05). Among independent variables, concentration of emulsifier had the most effects on physical properties while whipping time. The ordinary points in surface response showed maximal points with physical property like colorimetric b value while other properties revealed saddle points. The 3-dimensional response surface graphs of the predicted regression models displayed decreasing loaf volumes with increasing whipping times and emulsifier concentrations beyond optimum levels. The optimum conditions for best loaf volume and textural property (hardness, gummimess and chewiness) of the products selected by extracting intersectional areas of the contour maps that commonly overlapped all characteristics were; $11\~13$ min whipping time, $470\~486\;g$ amount of wheat flour, and $19\~20\;g$ emulsifier concentration, in case of single-stage method. The median values extracted from the RSM experimental results for optimum manufacturing conditions for single-stage method, i.e., 12 min whipping time, 478 g amount of wheat flour, and 20 g emulsifier concentration were empirically proven to fit the predicted levels of physical properties from the final foam cakes.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.6_2
• /
• pp.645-651
• /
• 2007

In general, contours in digital vector maps, which represent terrain characteristics and shape, are created by 3D digitizing the same height points using aerial photographs on the analytical or digital plotters with stereoscopic viewing. Hence, it requires lots of task, and subjective decision and experience of the operators. DTMs are generated indirectly by using contours since the national digital maps do not include digital terrain model (DTM) data. In this study, model key points which depict the important information about terrain characteristics were extracted from the contours. Further, determination of the efficient and flexible grid sizes were proposed to generate optimal DTM in terms of both quantitative and qualitative aspects. For this purpose, a progressive sampling technique was implemented, i.e., the smaller grid sizes are assigned for the mountainous areas where have large relief while the larger grid sizes are assigned for the relatively flat areas. In consequence, DTMs with multi-grid for difference areas could be generated instead of DTMs with a fixed grid size. The multi-grid DTMs reduce computations for data processing and provide fast display.