• Steel and Composite Structures
• /
• 제7권3호
• /
• pp.219-240
• /
• 2007

An analytical-numerical procedure has been presented in this paper to take into account the nonlinear effects of concrete cracking and time-dependent effects of creep and shrinkage in the concrete portion of the continuous composite beams under service load. The procedure is analytical at the element level and numerical at the structural level. The cracked span length beam element consisting of uncracked zone in middle and cracked zones near the ends has been proposed to reduce the computational effort. The progressive nature of cracking of concrete has been taken into account by division of the time into a number of time intervals. Closed form expressions for stiffness matrix, load vector, crack lengths and mid-span deflection of the beam element have been presented in order to reduce the computational effort and bookkeeping. The procedure has been validated by comparison with the experimental and analytical results reported elsewhere and with FEM. The procedure can be readily extended for the analysis of composite building frames where saving in computational effort would be very considerable.

• Structural Monitoring and Maintenance
• /
• 제7권1호
• /
• pp.1-12
• /
• 2020

Railway tracks are the direct supporting structures of the trains, which are vulnerable to produce large deformation under the temperature stress or subgrade settlement. The health status of track is critical, and the track should be routinely monitored to improve safety, lower the risk of excess deformation and provide reliable maintenance strategy. In this paper, the distributed optical fiber sensor was proposed to monitor the continuous deformation of the track. In order to validate the feasibility of the monitoring method, two deformation monitoring tests on one steel rail model in laboratory and on one real railway tack in outdoor were conducted respectively. In the model test, the working conditions of simply supported beam and continuous beam in the rail model under several concentrated loads were set to simulate different stress conditions of the real rail, respectively. In order to evaluate the monitoring accuracy, one distributed optical fiber sensor and one fiber Bragg grating (FBG) sensor were installed on the lower surface of the rail model, the strain measured by FBG sensor and the strain calculated from FEA were taken as measurement references. The model test results show that the strain measured by distributed optical fiber sensor has a good agreement with those measured by FBG sensor and FEA. In the outdoor test, the real track suffered from displacement and temperature loads. The distributed optical fiber sensor installed on the rail can monitor the corresponding strain and temperature with a good accuracy.

• Structural Engineering and Mechanics
• /
• 제9권5호
• /
• pp.491-504
• /
• 2000

A convenient method for enhancing the strength and stiffness of existing reinforced concrete beams is to bond adhesively steel plates to their tension faces. However, there is a limit to the applicability of tension face plating as the tension face plates are prone to premature debonding and, furthermore, the addition of the plate reduces the ductility of the beam. An alternative approach to tension face plating is to bond adhesively steel plates to the sides of reinforced concrete beams, as side plates are less prone to debonding and can allow the beam to remain ductile. Debonding at the ends of the side plates due to flexural forces, that is flexural peeling, is studied in this paper. A fundamental mathematical model for flexural peeling is developed, which is calibrated experimentally to produce design rules for preventing premature debonding of the plate-ends due to flexural forces. In the companion paper, the effect of shear forces on flexural peeling is quantified to produce design rules that are applied to the strengthening and stiffening of continuous reinforced concrete beams.

• International Journal of Concrete Structures and Materials
• /
• 제7권1호
• /
• pp.51-59
• /
• 2013

The use of light-gauge steel framing in low-rise commercial and industrial building construction has experienced a significant increase in recent years. In such construction, the wall framing is an assembly of cold-formed steel (CFS) studs held between top and bottom CFS tracks. Current construction methods utilize heavy hot-rolled steel sections, such as steel angles or hollow structural section tubes, to transfer the load from the end seats of the floor joist and/or from the load-bearing wall studs of the stories above to the supporting load-bearing wall below. The use of hot rolled steel elements results in significant increase in construction cost and time. Such heavy steel elements would be unnecessary if the concrete slab thickening on top of the CFS wall can be made to act compositely with the CFS track. Composite action can be achieved by attaching stand-off screws to the track and encapsulating the screw shank in the deck concrete. A series of experimental studies were performed on full-scale test specimens representing concrete/CFS flexural elements under gravity loads. The studies were designed to investigate the structural performance of concrete/CFS simple beams and concrete/CFS continuous headers. The results indicate that concrete/CFS composite flexural elements are feasible and their structural behavior can be modeled with reasonable accuracy.

• 한국강구조학회 논문집
• /
• 제20권2호
• /
• pp.237-246
• /
• 2008

연속경간을 가지는 I형강 교량은 내부 지점근처에서 상대적으로 큰 부모멘트가 발생하게 되는데, 이에 경제적인 단면 활용을 위하여 내부 지점부위의 상부 및 하부플랜지에 플레이트를 보강한 변단면을 사용하고 있다. 본 연구에서는 기존 탄성 횡-비틀림 좌굴식에 관한 연구를 토대로 하여 비탄성 구간에 있는 계단식 I형보의 횡-비틀림 좌굴강도를 범용구조해석프로그램 ABAQUS(2006)를 이용하여 산정하고, 간편한 설계식을 제안하고 있다. 유한요소해석에는 4절점 쉘요소인 S4R이 사용되었고, 국내외에서 많이 사용되는 I형강 단면(${W36{\times}160}$)을 대상으로 하였다. 양단 및 한쪽 끝단에 계단식 단면을 가지는 보에 대해서 고려하였으며, 플랜지 길이방향 비, 너비방향 비, 두께의 비로 계단식 I형보를 나타내었다. 해석에 사용된 매개변수는 각각 27가지 및 36가지 조합이고, 하중조건으로 보의 순수굽힘이 발생하는 균일모멘트를 적용시켰으며, 비탄성 구간범위 내에 있는 비지지 길이에 대하여 구조해석을 수행하였다. 비탄성 횡-비틀림 거동을 보기 위하여 잔류응력 및 초기결함을 고려한 비선형해석을 실시하였는데, Pi(1995)등이 고려한 잔류응력의 형상과 국내 I형강 표준 치수 허용치에 근거하여 부재 길이의 0.1%를 초기제작오차로 고려하였다. 본 연구 결과는 다양한 형식의 I형보가 사용되는 빌딩 및 교량의 경제적이고 합리적인 설계의 근간을 제공해 줄 것이며, 향후 다양한 하중 조건을 가지는 양단 또는 일단 계단식 단면 변화보의 비탄성 횡-비틀림 좌굴강도를 계산할 수 있는 설계식 개발에 적극 활용 될 수 있을 것이다.

• Structural Engineering and Mechanics
• /
• 제55권4호
• /
• pp.765-784
• /
• 2015

Connections are usually designed either as pinned usually associated with simple construction or rigid normally is associated with continuous construction. However, the actual behaviour falls in between these two extreme cases. The use of partial strength or semi-rigid connections has been encouraged by Euro-code 3 and studies on semi-continuous construction have shown substantial savings in steel weight of the overall construction. Composite connections are proposed in this paper as partial or full strength connections. Standardized connection tables are developed based on checking on all possible failure modes as suggested by "component method" for beam-to-column composite connection on major axis. Four experimental tests were carried out to validate the proposed standardised connection table. The test results showed good agreement between experimental and theoretical values with the ratio in the range between 1.06 to 1.50. All tested specimens of the composite connections showed ductile type of failure with the formation of cracks occurred on concrete slab at maximum load. No failure occurred on the Trapezoidal Web Profiled Steel Section as beam and on the British Section as column.

• 한국공작기계학회논문집
• /
• 제12권3호
• /
• pp.58-67
• /
• 2003

Welding characteristics of austienite 304 stainless and SM45C using a continuous wave Nd:YAG laser n experimentally investigated Laser beam welding is increasingly being used in welding of structural steels. The laser welding process is one of the most advanced manufacturing technologies owing to its high speed and deep penetration. The thermal cycles associated with laser welding are generally much Inter than those involved in conventional welding processes, leading to a rather small weld zone. Experiments are performed for 304 stainless steel plates changing several process parameter such as laser power, welding speed, shielding gas flow rate, presence of surface pollution, with fixed or variable gap and misalignment between the similar and dissimilar and plates, etc. The Nd:YAG laser welding process is one of the most advanced manufacturing technologies owing to its high speed and penetration. This paper describes the weld ability of SM45C carbon steel for machine structural use by Nd:YAG laser. The follow conclusions can be drawn that laser power and welding speed have a pronounced effect on size and shape of the fusion zone. Increase in welding speed resulted in an increase in weld depth/aspect ratio and hence a decrease in the fusion zone size. The penetration depth increased with the increase in laser power.

• 한국전산구조공학회논문집
• /
• 제29권3호
• /
• pp.269-275
• /
• 2016

본 논문은 유공형 판 형태로 전단 보강한 넓은 보의 중심에 기둥을 삽입하여 연속한 두 경간으로 설계하여 전단파괴 실험을 통해 넓은 보의 거동을 평가하였다. 유공형 강판으로 전단 보강된 시험체 5개와 유공형 GFRP판으로 보강된 시험체 3개 총 8개의 시험체를 전단파괴 실험을 통해 계측한 전단강도와 ACI-318 규준의 설계식을 통해 얻은 전단강도와 비교 평가하였다. 또한 넓은 보의 지지부 폭, 지지부의 형상과 전단보강재의 재료를 변수로 하여 넓은 보의 전단강도에 미치는 영향을 분석하였다. 이를 통해 지지부 폭이 증가할수록 전단강도가 증가하고 하중의 집중을 방지하는 것을 확인하였다. 또한 전단보강재의 재료인 강재와 GFRP에 상관없이 전단보강량이 동일하다면 넓은 보에서 비슷한 전단보강효과를 보이는 것을 확인하였다.

• Earthquakes and Structures
• /
• 제16권1호
• /
• pp.83-96
• /
• 2019

The seismic behavior of PRC coupling beam-hybrid coupled shear wall system is analyzed by using the finite element software ABAQUS. The stress distribution of steel plate, reinforcing bar in coupling beam, reinforcing bar in slab and concrete is investigated. Meanwhile, the plastic hinges developing law of this hybrid coupled shear wall system is also studied. Further, the effect of coupling ratio, section dimensions of coupling beam, aspect ratio of single shear wall, total height of structure and the role of slab on the seismic behavior of the new structural system. A fitting formula of plate characteristic values for PRC coupling beams based on different displacement requirements is proposed through the experimental date regression analysis of PRC coupling beams at home and abroad. The seismic behavior control method for PRC coupling beam-hybrid coupled shear wall system is proposed based on the continuous connection method and through controlling the coupling ratio, the roof displacement, story drift angle of hybrid coupled shear wall system, displacement ductility of coupling beam.

• Steel and Composite Structures
• /
• 제33권3호
• /
• pp.403-432
• /
• 2019

Axially functionally graded (AFG) beams are a new class of composite structures that have continuous variations in material and/or geometrical parameters along the axial direction. In this study, the exact analytical solutions for the free vibration of AFG and uniform beams with general elastic supports are obtained by using Euler-Bernoulli beam theory. The elastic supports are modeled with linear rotational and lateral translational springs. Moreover, the material and/or geometrical properties of the AFG beams are assumed to vary continuously and together along the length of the beam according to the power-law forms. Accordingly, the accuracy, efficiency and capability of the proposed formulations are demonstrated by comparing the responses of the numerical examples with the available solutions. In the following, the effects of the elastic end restraints and AFG parameters, namely, gradient index and gradient coefficient, on the values of the first three natural frequencies of the AFG and uniform beams are investigated comprehensively. The analytical solutions are presented in tabular and graphical forms and can be used as the benchmark solutions. Furthermore, the results presented herein can be utilized for design of inhomogeneous beams with various supporting conditions.