• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1155-1160
• /
• 1999

The screening methodology modeling, dispersion modeling procedures for continuous and instantaneous releases of the gas phase flow from the storage tank and pressure relief valve were considered. This study was performed to develop the screening methodology for prediction and control of hazardous/toxic gas releases by estimating the 1-hr average maximum ground-level concentration of $Cl_2$ gas vs. downwind distance by incorporating source term model including the general/physical properties of released material and release mode of the $Cl_2$ storage tank of the chemical plant facilities, dispersion model, and meteorological/topographical data into the TSCREEN model. As the results of the study, it was found that dispersion modes of the dense gas were affected by the state of the released material, the released conditions, physical-chemical properties of released material, and the released modes (continuous and instantaneous releases), and especially largely affected by initial (depressurized) density of the released material and release emission rate as well as the wind velocity. Especially, this study was considered to release hazardous material as meteorological data. It was thought that this screening methodology can be useful as a preliminary guideline for application of the refined analysis model by developing the generic sliding scale methodology for various senarios selected.

• Journal of Pharmaceutical Investigation
• /
• v.36 no.6
• /
• pp.355-361
• /
• 2006

Intraarticular corticosteroid injections for therapy of rheumatic arthritis are administered with the aim of optimal local anti-inflammatory effect at the injection site. Since the side effects of corticosteroidal drug, dexamethasone(DEX), administered at hish dose limited the therapeutic efficacy, there was a need to design a new drug delivery system for controlled release of dexamethasone. As a prodrug for continuous therapeutic efficacy, dexamethasone-21-palmitate(DEX-PAL) was prepared via esterification of palmitoyl chloride and dexamethasone. DEX-PAL was identified by NMR and MASS analysis. DEX-PAL or DEX was entrapped in lipid nanosphere which could be prepared by using a self emulsification-solvent evaporation method. Physicochemical characteristics such as mean particle diameter, zeta potential and drug loading efficiency of the lipid nanospheres were investigated with variation of either the kind of lipid or the lipid composition. The lipid nanospheres had a mean diameter $83{\sim}95$ nm and DEX-PAL loading efficiency of up to 95%. The drug loading efficiency increased with the increase of aliphatic chain length attached to the phospholipid. The incorporation of cationic lipid was very efficient for both reducing particle size of lipid nanospheres and enhancing drug loading efficiency. The lipid nanospheres containing DEX-PAL may be a promising novel drug carrier for the controlled release of the poorly water-soluble drugs.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.3
• /
• pp.290-297
• /
• 2011

The phenology of Campylaephora hypnaeoides J. Agardh and optimal conditions for carpospore release, growth and reproduction were examined in the field and in the laboratory from January to December 2007. In the field population of C. hypnaeoides, approximately 50% of the plants were vegetative during the study period. Additionally, the percentages of carposporophytes and tetrasporophytes were maximal in April (37%) and June (57%), respectively. Maximum growth in plant length, dry weight, and hook number coincided with the tetrasporophyte reproductive peak in the field. In culture, carpospore release, sporeling growth and reproduction were affected by environmental factors such as daylength, temperature, and salinity. The liberation of carpospores was maximum under continuous light and at a combination of $15^{\circ}C$ and $10\;{\mu}mol$ photons $m^{-2}\;s^{-1}$. Maximum growth of tetrasporophyte sporelings occurred at a combination of $20\;{\mu}mol$ photons $m^{-2}\;s^{-1}$ of constant light and $25^{\circ}C$. However, the growth of gametophyte sporelings was maximal under $40\;{\mu}mol$ photons $m^{-2}\;s^{-1}$ of constant light and in a combination of $20^{\circ}C$ and 35 psu. The tetrasporophyte sporelings were grew faster than gametophytes, indicating that gametophyte- and tetrasporophyte-sporelings have different physiological responses to irradiance and temperature. Tetrasporangial branches and cystocarps of C. hypnaeoides were produced from carpospores and tetraspores within 1 month, and they were stimulated at high temperature and irradiance levels. In conclusion, C. hypnaeoides should be seeded using carpospores during early winter (November-December) because cystocarps are easily identified by fishermen, and tetrasporophytes grow faster than gametophytes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.411.1-411.1
• /
• 2014

This study evaluates the utility of an antibacterial microneedle composed of green tea extract (GT) and hyaluronic acid (HA), for the efficient delivery of GT. These microneedles have the potential to be a patient-friendly method for the conventional sustained release of drugs. In this study, a fabrication method using a mold-based technique to produce GT/HA microneedles with a maximum area of ${\sim}60mm^2$ with antibacterial properties was used to manufacture transdermal drug delivery systems. Fourier transform infrared (FTIR) spectrometry was carried out to observe the potential modifications in the microneedles, when incorporated with GT. The degradation rate of GT in GT/HA microneedles was controlled simply by adjusting the HA composition. The effects of different ratios of GT in the HA microneedles were determined by measuring the release properties. In HA microneedles loaded with 70% GT (GT70), a continuous higher release rate were sustained for 72 h. The in vitro cytotoxicity assays demonstrated that GT/HA microneedles are not generally cytotoxic to chinese hamster ovary cells (CHO-K1), human embryonic kidney cells (293T), and mouse muscle cells (C2C12), which were treated for 12 and 24 h. Antimicrobial activity of the GT/HA microneedles was demonstrated by ~95% growth reduction of gram negative [Escherichia coli (E. coli), Pseudomonas putida (P. putida) and Salmonella typhimurium (S. typhimurium)] and gram positive bacteria [Staphylococcus aureus (S. Aureus) and Bacillus subtilis (B. subtilis)], with GT70. Furthermore, GT/HA microneedles reduced bacterial growth in the infected skin wound sites and improved skin wound healing process in rat model.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.4
• /
• pp.491-500
• /
• 2010

Three experiments were conducted to investigate the effects of polyurethane coated urea on in vitro ruminal fermentation, ammonia release dynamics and lactating performance of Holstein dairy cows fed a steam-flaked corn-based diet. In Exp. 1, a dual-flow continuous culture was run to investigate the effect of polyurethane coated urea on nutrient digestibility, rumen fermentation parameters and microbial efficiency. Three treatment diets with isonitrogenous contents (13.0% CP) were prepared: i) feedgrade urea (FGU) diet; ii) polyurethane coated urea (PCU) diet; and iii) isolated soy protein (ISP) diet. Each of the diets consisted of 40% steam-flaked corn meal, 58.5% forages and 1.5% different sources of nitrogen. PCU and FGU diets had significantly lower digestibility of NDF and ADF (p<0.01) than the ISP diet. Nitrogen source had no significant effect (p = 0.62) on CP digestibility. The microbial efficiency (expressed as grams of microbial N/kg organic matter truly digested (OMTD)) in vitro of the PCU diet (13.0 g N/kg OMTD) was significantly higher than the FGU diet (11.3 g N/kg OMTD), but comparable with the ISP diet (14.7 g N/kg OMTD). Exp. 2, an in vitro ruminal fermentation experiment, was conducted to determine the ammonia release dynamics during an 8 h ruminal fermentation. Three treatment diets were based on steam-flaked corn diets commonly fed to lactating cows in China, in which FGU, PCU or soybean meal (SBM) was added to provide 10% of total dietary N. In vitro $NH_3-N$ concentrations were lower (p<0.05) for the PCU diet than the FGU diet, but similar to that for the SBM diet at all time points. In Exp. 3, a lactation trial was performed using 24 lactating Holstein cows to compare the lactating performance and blood urea nitrogen (BUN) concentrations when cows were fed PCU, FGU and SBM diets. Cows consuming the PCU diet had approximately 12.8% more (p = 0.02) dietary dry matter intake than those consuming the FGU diet. Cows fed the PCU diet had higher milk protein content (3.16% vs. 2.94%) and lower milk urea nitrogen (MUN) concentration (13.0 mg/dl vs. 14.4 mg/dl) than those fed the FGU diet. Blood urea nitrogen (BUN) concentration was significantly lower for cows fed the PCU (16.7 mg/dl) and SBM (16.4 mg/dl) diets than the FGU (18.7 mg/dl) diet. Cows fed the PCU diet had less surplus ruminal N than those fed the FGU diet and produced a comparable lactation performance to the SBM diet, suggesting that polyurethane coated urea can partially substitute soybean meal in the dairy cow diet without impairing lactation performance.

• Journal of the Korea Concrete Institute
• /
• v.15 no.6
• /
• pp.802-810
• /
• 2003

In this paper, the modified singular fracture process zone (S-FPZ) model is proposed to consider variation of a fracture criterion for continuous crack propagation in concrete. The fracture properties of the proposed fracture model are strain energy release rate at a micro-crack tip and crack closure stress (CCS) versus crack opening displacement (COD) relationship in the FPZ. The proposed model can simulate the estimated fracture energy of experimental results. The analysis results of the experimental data shows that specimen geometry and loading condition did not affect the CCS-COD relation. But the strain energy release rate is a function of not only specimen geometry but also crack extension. Until 25 mm crack extension, the strain energy release rate is a constant minimum value, and then it increased linearly to the maximum value. The maximum fracture criterion occurred at the peak load for an large size specimen. The fracture criterion remains the maximum value after the peak load. The variation of the fracture criterion is caused by micro-cracking and micro-crack localizing. The fracture criterion of strain energy release rate can simply be the size effect of concrete fracture, and it can be used to quantify the micro-tracking and micro-crack localizing behaviors of concrete.

• International Commerce and Information Review
• /
• v.15 no.4
• /
• pp.267-286
• /
• 2013

The WCO Time Release Study (TRS) is a unique tool and method for measuring the actual performance of Customs activities. The ultimate aim of TRS is to improve the performance of the function being measured. To be more specific, TRS is used for identifying bottlenecks in the international supply chain and/or constraints affecting Customs release, assessing newly introduced and modified techniques, procedures, technologies and infrastructure, or administrative changes, establishing baseline trade facilitation performance measurement, identifying opportunities for trade facilitation improvements and estimating the country's approximate comparative position as a benchmark tool. The effective utilization methods of TRS for trade facilitation in Korea Customs Services are as follows ; Firstly, it is necessary to make every efforts to identify bottlenecks in border-related procedures and improve their procedures for continuous and more improved trade facilitation. Secondly, it is necessary to optimize and simplify export-related procedures using the TRS in exportation for efficiency of total international supply chain. Thirdly, it is necessary to make coordinated border management with main trading partners. Lastly, it is necessary to enhance Korea's international status to support underdeveloped countries in the field of trade procedures.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7A
• /
• pp.649-658
• /
• 2006

Recently, Software Development was applied to new-approach methods as a various form : client-server system and web-programing, object-orient concept, distributed development with a network environments. On the other hand, it be concerned about the distributed development technology and increasing of object-oriented methodology. These technology is spread out the software quality and improve of software production, reduction of the software develop working. Futures, we considered about the distributed software development technique with a many workstation. In this paper, we discussed optimal release problem based on a stochastic differential equation model for the distributed Software development environments. In the past, the software reliability applied to quality a rough guess with a software development process and approach by the estimation of reliability for a test progress. But, in this paper, we decided to optimal release times two method: first, SRGM with an error counting model in fault detection phase by NHPP. Second, fault detection is change of continuous random variable by SDE(stochastic differential equation). Here, we decide to optimal release time as a minimum cost form the detected failure data and debugging fault data during the system test phase and operational phase. Especially, we discussed to limitation of reliability considering of total software cost probability distribution.

• The Korean Journal of Urological Oncology
• /
• 제15권3호
• /
• pp.178-186
• /
• 2017

Purpose: Poloxamer 407 (P407) thermo-sensitive hydrogel formulations were developed to enhance the retention time in the urinary bladder after intravesical instillation. Materials and Methods: P407 hydrogels (P407Gels) containing 0.2 w/w% fluorescein isothiocyanate dextran (FD, MW 4 kDa) as a fluorescent probe were prepared by the cold method with different concentrations of the polymer (20, 25, and 30 w/w%). The gel-forming capacities were characterized in terms of gelation temperature (G-Temp), gelation time (G-Time), and gel duration (G-Dur). Homogenous dispersion of the probe throughout the hydrogel was observed by using fluorescence microscopy. The in vitro bladder simulation model was established to evaluate the retention and drug release properties. P407Gels in the solution state were administered to nude mice via urinary instillation, and the in vivo retention behavior of P407Gels was visualized by using an in vivo imaging system (IVIS). Results: P407Gels showed a thermo-reversible phase transition at $4^{\circ}C$ (refrigerated; sol) and $37^{\circ}C$ (body temperature; gel). The G-Temp, G-Time, and G-Dur of FD-free P407Gels were approximately $10^{\circ}C-20^{\circ}C$, 12-30 seconds, and 12-35 hours, respectively, and were not altered by the addition of FD. Fluorescence imaging showed that FD was spread homogenously in the gelled P407 solution. In a bladder simulation model, even after repeated periodic filling-emptying cycles, the hydrogel formulation displayed excellent retention with continuous release of the probe over 8 hours. The FD release from P407Gels and the erosion of the gel, both of which followed zero-order kinetics, had a linear relationship ($r^2=0.988$). IVIS demonstrated that the intravesical retention time of P407Gels was over 4 hours, which was longer than that of the FD solution (<1 hour), even though periodic urination occurred in the mice. Conclusions: FD release from P407Gels was erosion-controlled. P407Gels represent a promising system to enhance intravesical retention with extended drug delivery.

• Journal of Plant Biotechnology
• /
• v.49 no.3
• /
• pp.163-170
• /
• 2022

There is a continuous rise in the commercialization of living modified (LM) organisms worldwide. While LM plants have not yet been cultivated in South Korea, research, development, import of products, and registration of related research facilities are progressing. LM plants should be tested in greenhouses and fields during development. Furthermore, environmental risk assessment and safety management should be performed before their release into the environment. Research on LM plant development is conducted in laboratories as well as confined greenhouses and fields. Safety management regulations are provided as combination standards for the LMO Act in each research district. The accidental release of the LM petunia in Japan was a significant incident related to LM plant research. It implies that normal plants within the distance of crossing should be regarded as LM plants. In the United States, LM creeping bentgrass was released into the environment, thus necessitating the establishment of stringent measures to prevent the scattering of LM plant seeds by wind or other mediums. In South Korea, LM Zoysia and LM cotton were released through rainwater. Therefore, safety measures that prevent LM seed mixing and plant vegetative propagules escaping into the environment via rainwater must be established. Preventing the dispersal of unapproved LM plants requires significant time, expenditure, and effort. Researchers should first identify the impact of LM plants on the ecosystem, and steps to avert their environmental release must be implemented.