• Journal of Biosystems Engineering
• /
• 제40권3호
• /
• pp.296-304
• /
• 2015

Purpose: The balance between miscanthus production and its cost effectiveness depends greatly on its moisture content during post processing. The objective of this research was to measure the moisture content using a non-destructive and non-contact methodology for in situ applications. Methods: The moisture content of comminuted miscanthus was controlled using a closed chamber, a humidifier, a precision weigher, and a real-time monitoring software developed in this research. A CMOS sensor equipped with $50{\times}$ magnifier lens was used to capture magnified images of the conditioned materials with moisture content level from 5 to 30%. The hypothesis is that when light is incident on the comminuted particles in an inclined manner, higher moisture content results in light being reflected with a higher intensity. Results: A linear regression analysis for an initiative hypothesis based on general histogram analysis yielded insufficient correlations with low significance level (<0.31) for the determination coefficient. A significant relationship (94% confidence level) was determined at level 108 in a reverse accumulative histogram proposed based on a revised hypothesis. A linear regression model with the value at level 108 in the reverse accumulative histogram for a magnified image as the independent variable and the moisture content of comminuted miscanthus as the dependent variable was proposed as the estimation model. The calibrated linear regression model with a slope of 92.054 and an offset of 32.752 yielded 0.94 for the determination coefficient (RMSE = 0.2%). The validation test showed a significant relationship at the 74% confidence level with RMSE 6.4% (n = 36). Conclusions: To compensate the inconsistent significance between calibration and validation, an estimation model robust against various systematic interferences is necessary. The economic efficiency of miscanthus, which is a promising energy resource, can be improved by the real-time measurement of its crucial material properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.456-456
• /
• 2009

Boron doping on an n-type Si wafer is requisite process for IBC (Interdigitated Back Contact) solar cells. Fiber laser annealing is one of boron doping methods. For the boron doping, uniformly coated or deposited film is highly required. Plasma enhanced chemical vapor deposition (PECVD) method provides a uniform dopant film or layer which can facilitate doping. Because amorphous silicon layer absorption range for the wavelength of fiber laser does not match well for the direct annealing. In this study, to enhance thermal affection on the existing p-a-Si:H layer, a ${\mu}c$-Si:H intrinsic layer was deposited on the p-a-Si:H layer additionally by PECVD. To improve heat transfer rate to the amorphous silicon layer, and as heating both sides and protecting boron eliminating from the amorphous silicon layer. For p-a-Si:H layer with the ratio of $SiH_4$ : $B_2H_6$ : $H_2$ = 30 : 30 : 120, at $200^{\circ}C$, 50 W, 0.2 Torr for 30 minutes, and for ${\mu}c$-Si:H intrinsic layer, $SiH_4$ : $H_2$ = 10 : 300, at $200^{\circ}C$, 30 W, 0.5 Torr for 60 minutes, 2 cm $\times$ 2 cm size wafers were used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 20 ~ 27 % of power, 150 ~ 160 kHz, 20 ~ 50 mm/s of marking speed, and $10\;{\sim}\;50 {\mu}m$ spacing with continuous wave mode of scanner lens showed the correlation between lifetime and sheet resistance as $100\;{\Omega}/sq$ and $11.8\;{\mu}s$ vs. $17\;{\Omega}/sq$ and $8.2\;{\mu}s$. Comparing to the singly deposited p-a-Si:H layer case, the additional ${\mu}c$-Si:H layer for doping resulted in no trade-offs, but showed slight improvement of both lifetime and sheet resistance, however sheet resistance might be confined by the additional intrinsic layer. This might come from the ineffective crystallization of amorphous silicon layer. For the additional layer case, lifetime and sheet resistance were measured as $84.8\;{\Omega}/sq$ and $11.09\;{\mu}s$ vs. $79.8\;{\Omega}/sq$ and $11.93\;{\mu}s$. The co-existence of $n^+$layeronthesamesurfaceandeliminating the laser damage should be taken into account for an IBC solar cell structure. Heavily doped uniform boron layer by fiber laser brings not only basic and essential conditions for the beginning step of IBC solar cell fabrication processes, but also the controllable doping concentration and depth that can be established according to the deposition conditions of layers.

• 한국안광학회지
• /
• 제9권2호
• /
• pp.333-343
• /
• 2004

Impression cytology는 결막상피의 표층을 떼어내기 위해 안구 표면에 cellulose acetate filter 재질을 같이 이용한다. 이 방법은 비 침습적이고 쉽게 시행할 수 있으며 환자에게 최소한의 불편감을 주며 결막표면에 반복해서 시행하여 변화를 관찰하기 위해 사용될 수 있다. 이 방법으로 결막 표면의 형태학적 연구와 squmaous metaplasia의 정도를 평가할 수 있다. 본 연구는 건성안 환자에서 impression cytology를 이용하여 결막표면을 평가하기 위해 수행되었다. 70명의 콘택트렌즈 비착용 학생을 대상으로 조사하였는데 먼저 조사 대상자들에게 McMonnies dry eye symptom questionnaire을 작성하도록 하였다. 그리고 비침습성 tear thinning time(TTT) 검사를 시행하고 다음에 침습성 검사인 Schirmer tear test(SIT), tear film break-up time(TBUT) tests 그리고 Rose-bengal staining올 시행하여 건성안 의심자를 분류하였다. 하 안구결막으로부터 결막 상피세포는 impression cytology기법으로 수집하여 PAS(Periodic Acid Schift)-haematoxylin 염색을 시행하였다. 배상세포와 결막상피세포는 광학현미경 400배에서 관찰하여 squamous metaplasia의 정도에 근거한 Nelson Grading scale에 따라 분류하였는데 이는 배상세포 밀도, 세포의 크기와 형태, 핵:세포질 비 등을 포함한다. 건성안 의심자는 상피세포의 형태적 변화, 핵의 변화, 배상세포 밀도 감소를 보였다. 세포학적 변화 정도는 건성안 조건의 정도에 관련이 있었다. 상피세포 형태를 Nelson의 분류시스템으로 단계를 나눈 결과 대조군의 91.43%가 grade 0 이었고 8.57%가 약간의 이상형태인 grade 1이었다. 반면에 건성안 의심자에서는 20%가 grade 0, 42.86%가 grade 1, 34.29%가 grade 2 그리고 2.86%가 심한 형태적 변화를 보인 grade 3를 나타냈다. Impression cytology는 부작용이나 거부반응이 없는 안구 표면 상피의 비 침습적 또는 최소 침습적 생검법으로 생각되며 안구표면을 포함하는 광범위한 과정을 위한 유용한 진단 기법으로 안전하고 간단하며 건성안 의심자의 다양한 안구 표면 변화의 이해를 증진시키는데 도움을 줄 수 있을 것으로 사료된다.