• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.83-89
• /
• 1991

The partial discharge properties of interface layer in Mica-Epoxy composite, which has been mainly used for the coil insulating material of high voltage machinery, are different from those of resins due to the abnormal interface layer to be presented between inorganic material and resin. Accordingly, the study on discharge of interface in composite insulting system is strongly requsted for not only an increasing of insulating strength, but also the basical information of diagnosis system for high voltage equipment. As a result, it has been confirmed that the interface is an abnormal resin layer and the contact states at interface is depended upon the density of silane aqueous solution. Pulse frequency at abnormal interface shows a linear increasing with enlargement of discharge quantity. Whereas, in case of normal interface, pulse frequency property represents exponential increasing at the point of saturating. A life model can be diagramed from results of time dependance of skewness, and a survival life time can be quantified from the life model suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.128-131
• /
• 1992

In this paper, the skewness properties of partial discharge at interface layer in mica-epoxy composite material were investigated and studied on interface specimens which has internal electrodes. As a result, it has been confirmed that the interface exists as abnormal resin layer and the contact condition at the interface is depended upon the density of si lane aqueous solution. The Pulse frequency of discharge at abnormal interface has been shown a linear increasing with enlargement of discharge quantity according to rising of the applied voltage. Whereas, in case of normal interface, pulse frequency represented exponential increasing at the saturating point of discharge quantity. The aging model can be represented from the variable characteristics of skewness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.25-28
• /
• 2005

This paper was investigated the changes of surface properties of high-temperature-vulcanized(HTV) semiconductive silicone rubber due to oxygen plasma discharge. The modifications produced on the silicone surface by oxygen plasma were accessed using x-ray photoelectron spectroscopy(XPS), contact angle and Scanning Electron Microscope(SEM). The results of the chemical analysis showed that C-H bonds were broken due to plasma discharge and Silica-like bonds (SiOx. x=3~4) increased. It is thought that the above changes lead to the increase of surface energy of high-temperature-vulcanized(HTV) semiconductive silicone rubber. The micromorphology of surface and hydrophobicity due to plasma discharge based on our results were discussed.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1408_1409
• /
• 2009

It's described the discharge characteristics and ICP-AES analysis of insulators by surface deterioration in this paper. For the assessment of insulators, there are applied the conductivity of dusts, contact angle measurement of the insulator surfaces and the ingredient analysis in each area. Through the analysis of pollutants attached to insulators inside the tunnel, the cleaning cycle is discussed. As the results, it would be expected to the electrical safety.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1515-1518
• /
• 2009

Hydrophobic treatments were conducted for different kinds of substrates, glass substrate, silicon wafer and plastic substrate. Ar-$CH_4$ gas mixture was used as a discharge gas for the hydrophobic treatment. The change of the contact angle before and after treatment was measured and compared. Time evolution of the contact angle change after hydrophobic treatment was investigated.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2141-2143
• /
• 2000

In this paper, high concentration yield multi-discharge type ozonizer (MDO) of new discharge type using superposed silent discharge was designed and manufactured, MDO can be consisted with 3 kind of multi discharge type ozonizer (MDO) in accordance with power supply method that supplying power, which has 180[$^{\circ}$] phase difference, to 3 electrodes and double gap. At the moment, discharge characteristics and ozone generation characteristics of each MDO were investigated in accordance with quantity of supplied gas, the number of MDO, and the shapes of each MDO. In result, ozone generation characteristics of 17185[ppm] and 783[g/kWh] were obtained, and when ozone of 17185 [ppm] was in contact with dyeing water waste, decolorization characteristics was excellent, so it confirmed that MDO could be used as water environment improvement facility.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.1
• /
• pp.50-54
• /
• 1983

Contact resistance variation which may be called sliding noise in carbon film variable resistors whose resistance elements consists of linear resistivity distribution were measured with several kinds of sliders and were analyzed to reduce the contact resistance variation. About the measuring method, the standard method of measuring contact resistance variation specified by the variable Resistance Components Institute was adupted. By analyzing the experimental results, it has been shown that the primary cause of contact resistance variation is due to current constriction and small discharge sparks in the resistance film in the area close to the slide contact. Moreover, it has been found that the sliding noise would be reduced by increasing the number of contact points, sliding speed, and pressure, and by using some kinds of insulation oil on the contacting surface. High contact resistance variation is likely to occur in the area of high resistance variation in a logrithmic resistance taper.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.136-143
• /
• 1995

With the contact angle of phase dropping epoxy resin on the inorganic filler(glass plate) surface treated with air plasma, we have studied about the interfacial wettability between epoxy resin and glass plate as a simple model of glass fiber reinforced composite materials. The contact angle on the inorganic filler surface varied with surface treatment conditions. The contact angle significantly depends on plasma treating time and environment temperature in the oven. From the view point of plasma treatment condition in this work, when discharge conditions were pressure 200mtorr, voltage 800V, magnetic flux density 8OGauss, optimum treatment time were proved as 3,4 and 5 minutes for the environment of >$80^{\circ}C$, >$100^{\circ}C$ and >$120^{\circ}C$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.10-13
• /
• 2010

The plasma processing technologies of thin film deposition and surface treatment technique have been applied to many industrial fields. This study is purposed Large-area uniformity and surface treatment on the stainless substrate. We treat surface of stainless by $CF_4$ plasma. $CF_4$ plasma is generated by using SPM(Scanning plasma method)which is kind a of CVD. Generally, SPM has been used for uniform surface treatment using a crossed electromagnetic field. The optimum discharge condition has been studied for the gas pressure, the magnetic flux density and the distance between substrate and electrodes. In result, contact angle is increased by surface treatment using $CF_4$ Plasma. Therefore we expect that SPM to control contact angle is applied to many industries.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.164-168
• /
• 2014

The sodium-sulfur batteries which operate at $350^{\circ}C$ have been mainly used in the field of energy storage system. This batteries consist of liquid sodium anode, sulfur cathode and ${\beta}^{{\prime}{\prime}}$-alumina solid electrolyte. The conditioning process for stabilization of the batteries is essential since the cells show considerable fluctuation of discharge voltage at the beginning of discharge/charge cycles. It is found that one of the reasons of the fluctuation is the gradual change of contact area between molten sodium and solid electrolyte.