• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.57-63
• /
• 2003

An eigenvalue design sensitivity formulation of a general nonsymmetric-matrix rotor-bearing system is devised. using the DDM (direct differential method). Then, investigations on the design sensitivities of critical speeds are carried out for an APU turbogenerator with a spline shaft connection. Results show that the dependence of the rate of change of the critical speed on the stiffness changes of bearing models of spline shaft connection points is negligible, and thereby their modeling uncertainty does not present any problem. And the passing critical speeds up to the 4th critical speed are not sensitive to the design stiffness coefficients of four main bearings. Further, the dependence of the rate of change of the critical speed on the shaft-element length changes shows quantitatively that the spline shaft has some limited influence on the 4th critical speed but no influence on the 1st to 3rd critical speeds. With no adverse effect from the spline shaft, the APU system achieves a critical speed separation margin of more than 40% at a rated speed of 60,000 rpm.

• 대한전자공학회논문지TC
• /
• 제40권11호
• /
• pp.27-33
• /
• 2003

데이터 감시(AUDIT) 기능이란 분산 실장 되어 있는 데이터들을 대상으로 데이터 이상을 진단하고 불일치 데이터를 검출하여 이를 일치시키는 일련의 작업을 말하는 것으로 데이터 불일치로 인해 유발되는 시스템 문제를 최소화시키는데 목적을 둔다. 본 논문에서는 ATM 교환기의 연결 데이터의 대부분을 차지하고 있는 PVC(Permanent Virtual Circuit) 데이터에 대한 감사 기능 지원 방안을 제안하였다. 즉 고속/저속 가입자 링크에 대해 일정 시간마다 감사 기능의 주기적 수행과 운용자 명령어에 의한 즉각적인 감사 기능을 제안하여 PVC 정보의 불일치로 인한 데이터의 손실 및 시스템 장애를 최소화 할 수 있게 하였다. 또한 감사 기능으로 인해 연결 제어 프로세서와 DC(Device Controller) 사이에 송수신하는 많은 IPC(Inter Processor Communication) 메시지가 연결 제어 프로세서의 부하에 어떠한 영향을 미치는지 분석하였는데, 시스템 부하와 거의 무관하게 연결 제어 프로세서의 부하가 일정함을 확인하였다.

• Steel and Composite Structures
• /
• 제18권5호
• /
• pp.1103-1117
• /
• 2015

It is known that material properties, connection quality and manufacturing methods are among the important factors directly affecting the behavior of steel connections and hence steel structures. The possible performance differences between a fabricated connection and its computer model may cause critical design problems for steel structures. Achieving a reliable design depends, however, on how accurately the material properties and relevant constitutive models are considered to characterize the behavior of structures. Conventionally, the stress and strain fields in structural steel connections are calculated using the finite elements method with assumed material properties and constitutive models. Because the conventional strain gages allow the measurement of deformation only at one point and direction for specific time duration, it is not possible to determine the general characteristics of stress-strain distributions in connections after the laboratory performance tests. In this study, a new method is introduced to measure displacement distribution of simple steel welded connections under tension tests. The method is based on analyzing digital images of connection specimens taken periodically during the laboratory tension test. By using this method, displacement distribution of steel connections can be calculated with an acceptable precision for the tested connections. Calculated displacements based on the digital image correlation method are compared with those calculated using the finite elements method.

• Steel and Composite Structures
• /
• 제52권1호
• /
• pp.31-43
• /
• 2024

A very widely used analytical method (mathematical model), mentioned in Eurocode 3, to examine the connections' bending behavior is the component-based method that has certain weak points shown in the plastic behavior part of the moment-rotation curves. In the component method available in Eurocode 3, for simplicity, the effect of strain hardening is omitted, and the bending behavior of the connection is modeled with the help of a two-line diagram. To make the component method more efficient and reliable, this research proposed its advanced version, wherein the plastic part of the diagram was developed beyond the guidelines of the mentioned Regulation, implemented to connect the end plate, and verified with the moment-rotation curves found from the laboratory model and the finite element method in ABAQUS. The findings indicated that the advanced component method (the method developed in this research) could predict the plastic part of the moment-rotation curve as well as the conventional component-based method in Eurocode 3. The comparison between the laboratory model and the outputs of the conventional and advanced component methods, as well as the outputs of the finite elements approach using ABAQUS, revealed a different percentage in the ultimate moment for bolt-extended end-plate connections. Specifically, the difference percentages were -31.56%, 2.46%, and 9.84%, respectively. Another aim of this research was to determine the optimal dimensions of the end plate joint to reduce costs without letting the mechanical constraints related to the bending moment and the resulting initial stiffness, are not compromised as well as the safety and integrity of the connection. In this research, the thickness and dimensions of the end plate and the location and diameter of the bolts were the design variables, which were optimized using Particle Swarm Optimization (PSO), Snake Optimization (SO), and Teaching Learning-Based Optimization (TLBO) to minimization the connection cost of the end plate connection. According to the results, the TLBO method yielded better solutions than others, reducing the connection costs from 43.97 to 17.45€ (60.3%), which shows the method's proper efficiency.

• 대한건축학회논문집:구조계
• /
• 제34권3호
• /
• pp.19-28
• /
• 2018

Key factors that ensure competitiveness of modular unit include consistent high quality and connection condition that ensures high structural performance while minimizing the overall scale of the on-site process. However, it is difficult to evaluate the structural performance of the connection of modular unit, and its structural analysis and design method can be different depending on the connection to its development, which affects the seismic performance of its final design. In particular, securing the seismic performance is the key to designing modular systems of mid-to-high-rise structure. In this paper, therefore, the seismic performance of the modular system with bracket-typed fully restrained moment connections according to stiffness and the shapes of various connection members was evaluated through experimental and analytical methods. To verify the seismic performance, a cyclic loading test of the connection joint of the proposed modular system was conducted. As a result of this study, theoretical values and experimental results were compared with the initial stiffness, hysteresis behavior and maximum bending moment of the modular system. Also, the connection joint was modeled, using the commercial program ANSYS, which was then followed by finite element analysis of the system. According to the results of the experiment, the maximum resisting force of the proposed connection exceeded the theoretical parameters, which indicated that a rigid joint structural performance could be secured. These results almost satisfied the criteria for connection bending strength of special moment frame listed on KBC2016.

• 한국지진공학회논문집
• /
• 제22권1호
• /
• pp.23-32
• /
• 2018

In this study, we conducted a shake table test to verify the seismic performance of the paneling system with steel truss composed of bolt connections. The control group was set to the traditional paneling system with steel truss connected by spot welding method. Test results showed that the bolted connection type paneling system has excellent deformation capacity without cracking or brittle fracture of the steel truss connection parts compared to the welding type paneling system. Furthermore, in the bolted connection type, slight damage occurred at the time of occurrence of the same story drift angle as compared with the existing method, it is considered that it has excellent seismic performance. In compliance with the performance-based design recommended for the current code (ASCE 41-13) on non-structural components, it is judged that in the case of the bolted connection type paneling system, it can be applied to all risk category structures without restriction. However, in the case of traditional paneling system with spot welding method, it is considered that it can be applied limitedly.

• Steel and Composite Structures
• /
• 제45권2호
• /
• pp.231-248
• /
• 2022

Hybrid Steel-Trussed Concrete Beam (HSTCB) is structural typology suitable for light industrialization. HSTCBs usually cover long span with small depths, which lead to significant amount of longitudinal rebars. The latter make beam-column joints more prone to damage due to earthquake-induced cyclic actions. This phenomenon can be avoided using friction-based BCCs. Friction devices at Beam-to-Column Connections (BCCs) have become promising solutions to reduce the damage experienced by structural members during severe earthquakes. Few solutions have been developed for cast-in-place Reinforced Concrete (RC) and steel-concrete composite Moment Resisting Frames (MRFs), because of the difficulty of designing cost-effective damage-proof connections. This paper proposes a friction-based BCC for RC MRFs made with HSTCBs. Firstly, the proposed connection is described, and its innovative characteristics are emphasized. Secondly, the design method of the connection is outlined. A detailed 3D FE model representative of a beam-column joint fitted with the proposed connection is developed. Several monotonic and cyclic analyses are performed, investigating different design moment values. Lastly, the numerical results are discussed, which demonstrate the efficiency of the proposed solution in preventing damage to RC members, and in ensuring satisfactory dissipative capacity.

• 한국시뮬레이션학회논문지
• /
• 제29권2호
• /
• pp.95-103
• /
• 2020

본 논문에서는 경량구조 적용을 위한 구조 접합부 설계를 제시하였다. 압력에 대한 구조 안정성 연구를 위하여 용접부 접합부와 볼트 접합부에 대한 모델을 설계하였다. 확립된 모델의 신뢰성 검증을 위하여, 비선형 해석을 수행하였고, 실험결과와 비교하였을 때 유사한 결과를 확인하였다. 또한 비교연구를 통하여 구조설계 재료와 적합한 용접방법을 선택하였으며, 볼트의 개수와 위치에 따른 파단하중 시뮬레이션을 진행하여 응력에 따른 안정성을 분석하였다. 마지막으로, 접합부 모델을 기반으로 경량 구조를 모델링하고 구조 해석을 수행하였다. 그 결과, 용접부와 볼트체결을 적용하여 설계된 구조가 접합부를 적용하지 않은 구조에 비해 최대응력이 31.4% 감소함을 확인하였다. 이 결과를 토대로, 경량구조의 안정성 해석 시 접합부 모델링의 필요성을 확인하였다.

• 대한전자공학회논문지SD
• /
• 제43권10호
• /
• pp.68-73
• /
• 2006

본 논문에서는 SoC(System On a Chip)의 효율적인 설계와 빠른 검증을 위해서 Active-HDL과 Matlab의 Simulink를 연동하여 HDL, SystemC 및 알고리즘 레벨의 추상화를 동시에 통합하여 시뮬레이션 할 수 있는 방법론을 제시하고, 이를 이용한 다채널 스피커의 직렬연결 기법을 설계 및 구현하였다. 구현은 ARM 프로세서와 Xilinx Virtex4 FPGA를 기반으로 하고 AMBA 버스를 사용하여 연동하는 SoC Master 보드 상에서 이루어졌다. 이러한 방법은 하드웨어 부분의 RTL 코드를 IP화하여 소프트웨어 부분과 동시에 검증 할 수 있는 장점을 가지고 있으며 직렬 연결 스피커 시스템과 같이 많은 신호처리를 하는 부분에서 쉽고 빠르게 설계를 진행할 수 있음을 보였다.

• 복합신소재구조학회 논문집
• /
• 제5권1호
• /
• pp.22-27
• /
• 2014

The flat plate slab system have many good features, which are design flexibilities, saving of story-height and economy of construction etc. But the study of flat plate slab system for H-steel column have been rare both at home and abroad. Recently high-rise residential and commercial buildings have been constructed in urban areas in Korea. The suggested dowel connection system is more likely to adoptable because it remarkably contribute to save inter story height and also to have many advantages compared with conventional steel works such as H-Steel frame + Deck plate slab system. This study aims at developing design method and program for connection between H-Steel column and flat plate slab system, which contribute to save significantly inter-story height.