• 한국화재소방학회논문지
• /
• 제20권4호
• /
• pp.65-71
• /
• 2006

최근에 화재연구가 활발해짐에 따라 화재특성을 평가하기 위해 중요한 물리량인 발열량 등을 측정하여 모델의 검증과 화재현상의 이해를 도모하고 있다. 이전의 화재연구에서는 실험공간이나 재정적 여건 때문에 축소모형 실험을 주로 수행하였지만, 다양한 화재의 특성을 축소모형에서 모두 도출할 수 없으므로 실제 규모의 화재에서 특성을 조사하는 것이 필요하다. 그러므로 보통 5MW 이상의 열량을 측정할 수 있는 대형 콘 칼로리미터를 20년 전부터 외국에서는 개발하였으며, 새로운 관련기술과 화재에 관한 지식을 바탕으로 개선되고 발전되어 왔다. 본 연구에서는 대형 콘 칼로리미터를 설계할 때 고려하여야 할 방법들을 각 요소별로 설명하고, 이를 통해 향후 개선을 위해 요구되는 지식이나 기술들을 제안하였다.

• Nuclear Engineering and Technology
• /
• 제54권5호
• /
• pp.1769-1780
• /
• 2022

A new method of dose calculation algorithm, called GPU-accelerated Monte Carlo and collapsed cone Convolution (GMCC) was developed to improve the calculation speed of BNCT treatment planning system. The GPU-accelerated Monte Carlo routine in GMCC is used to simulate the neutron transport over whole energy range and the Collapsed Cone Convolution method is to calculate the gamma dose. Other dose components due to alpha particles and protons, are calculated using the calculated neutron flux and reaction data. The mathematical principle and the algorithm architecture are introduced. The accuracy and performance of the GMCC were verified by comparing with the FLUKA results. A water phantom and a head CT voxel model were simulated. The neutron flux and the absorbed dose obtained by the GMCC were consistent well with the FLUKA results. In the case of head CT voxel model, the mean absolute percentage error for the neutron flux and the absorbed dose were 3.98% and 3.91%, respectively. The calculation speed of the absorbed dose by the GMCC was 56 times faster than the FLUKA code. It was verified that the GMCC could be a good candidate tool instead of the Monte Carlo method in the BNCT dose calculations.

• 대한치과교정학회지
• /
• 제44권5호
• /
• pp.229-235
• /
• 2014

Objective: The aim of this study was to assess artifacts induced by metallic restorations in three-dimensional (3D) dental surface models derived by cone-beam computed tomography (CBCT). Methods: Fifteen specimens, each with four extracted human premolars and molars embedded in a plaster block, were scanned by CBCT before and after the cavitated second premolars were restored with dental amalgam. Five consecutive surface models of each specimen were created according to increasing restoration size: no restoration (control) and small occlusal, large occlusal, disto-occlusal, and mesio-occluso-distal restorations. After registering each restored model with the control model, maximum linear discrepancy, area, and intensity of the artifacts were measured and compared. Results: Artifacts developed mostly on the buccal and lingual surfaces. They occurred not only on the second premolar but also on the first premolar and first molar. The parametric values increased significantly with increasing restoration size. Conclusions: Metallic restorations induce considerable artifacts in 3D dental surface models. Artifact reduction should be taken into consideration for a proper diagnosis and treatment planning when using 3D surface model derived by CBCT in dentofacial deformity patients.

• Computational Structural Engineering : An International Journal
• /
• 제2권1호
• /
• pp.33-42
• /
• 2002

A computationally efficient stiffness design method for building structures is proposed in which dynamic soil-structure interaction based on the wave-propagation theory is taken into account. A sway-rocking shear building model with appropriate ground impedances derived from the cone models due to Meek and Wolf (1994) is used as a simplified design model. Two representative models, i.e. a structure on a homogeneous half-space ground and a structure on a soil layer on rigid rock, are considered. Super-structure stiffness satisfying a desired stiffness performance condition are determined via an inverse problem formulation for a prescribed ground-surface response spectrum. It is shown through a simple yet reasonably accurate model that the ground conditions, e.g. homogeneous half-space or soil layer on rigid rock (frequency-dependence of impedance functions), ground properties (shear wave velocity), depth of surface ground, have extensive influence on the super-structure design.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2971-2976
• /
• 2007

The mode change from Taylor cone-jet to dripping in electrospraying has been analytically investigated. The change has been predicted by the dynamic behavior of a liquid drop at the tip of the cone-jet. Conservation laws are applied to determine the upward motion of the drop, and an instability model of electrified jets is used to determine the jet breakup. Finally, for the first time, the analysis enables prediction of the transition in terms of the Weber number and electric Bond number. The predictions are in good agreement with experimental data.

• 한국산학기술학회논문지
• /
• 제3권4호
• /
• pp.285-289
• /
• 2002

본 논문에서는 아이스크림용 아이스 콘에서 콘 부분을 만들기 위한 금형의 제작시 필요한 구조적 안정성을 평가 할 수 있는 유동해석을 수행하였다. 유동해석을 수행하기 위하여 상용 유한요소해석 코드인 ANSYS를 활용하였으며 내압조건, 경계조건, 구속조건 등을 고려하여 아이스 콘 금형 내부의 유동 흐름을 압력조건의 변화에 따라 구하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.877-888
• /
• 2021

The water entry behaviors of projectiles with different cone-headed angles were studied numerically, experimentally and theoretically, mainly focusing on the hydrodynamic impact in the initial stage. Based on MMALE algorithm, it was proposed a formula of impact deceleration, which relied on the initial entry velocity and cone-headed angle. Meanwhile, in order to verify the validity of the simulation model, experiments using accelerometer and high-speed camera were carried out, and their results were in a good agreement with simulation results. Also, theoretical calculation results of cavity diameter were compared with experiments and simulation results. It was observed that the simulation method had a good reliability, which would make forecast on impact deceleration in an engineering project.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3467-3472
• /
• 2007

The effects of the wall geometry on the spray-wall impingement process of a hollow-cone fuel spray emerging from a high-pressure swirl injector of the Gasoline Direct Injection (GDI) engine were investigated by means of a numerical method. The ized Instability Sheet Atomization (LISA) & Aerodynamically Progressed Taylor Analogy Breakup (APTAB) model for spray atomization process and the Gosman model were applied to model the atomization and wall impingement process of the spray. The calculation results of spray characteristics, such as a spray development process and a radial distance after wall impingement, compared with the experimental ones by the Laser Induced Exciplex Fluorescence (LIEF) technique. It was found that the radial distance of the cavity angle of 90$^{circ]$ after wall impingement was the shortest and the ring shaped vortex was generated near the wall after spray-wall impingement process.

• 한국분무공학회지
• /
• 제12권2호
• /
• pp.101-107
• /
• 2007

The purpose of this study is to analyze spray and evaporation characteristics of DME fuel at the high pressure and temperature. For the numerical analysis of dimethyl ether(DME) fuel spray characteristics, hybrid breakup model was applied to the DME spray and its breakup process. In order to obtain experimental results for comparison with the predicted ones, the visualization of the spray evolution process was executed by using a Nd:YAG laser. Also, the numerical investigation was conducted by the two hybrid models for primary and secondary breakup of the DME spray. The primary breakup model was used the Kelvin-Helmholtz(KH) breakup model. In the secondary breakup process, Rayleigh-Taylor(RT) and Drop Deformation Breakup(DDB) model was applied. The results of this study provide the macroscopic characteristics of the spray such as spray tip penetration and cone angle, and prediction accuracy of the two hybrid model.

• 대한치과교정학회지
• /
• 제42권4호
• /
• pp.169-181
• /
• 2012

Objective: The purpose of this study was to develop superimposition method on the lower arch using 3-dimensional (3D) cone beam computed tomography (CBCT) images and orthodontic 3D digital modeling. Methods: Integrated 3D CBCT images were acquired by substituting the dental portion of 3D CBCT images with precise dental images of an orthodontic 3D digital model. Images were acquired before and after treatment. For the superimposition, 2 superimposition methods were designed. Surface superimposition was based on the basal bone structure of the mandible by surface-to-surface matching (best-fit method). Plane superimposition was based on anatomical structures (mental and lingual foramen). For the evaluation, 10 landmarks including teeth and anatomic structures were assigned, and 30 times of superimpositions and measurements were performed to determine the more reproducible and reliable method. Results: All landmarks demonstrated that the surface superimposition method produced relatively more consistent coordinate values. The mean distances of measured landmarks values from the means were statistically significantly lower with the surface superimpositions method. Conclusions: Between the 2 superimposition methods designed for the evaluation of 3D changes in the lower arch, surface superimposition was the simpler, more reproducible, reliable method.