• 한국군사과학기술학회지
• /
• 제27권1호
• /
• pp.15-23
• /
• 2024

In order to avoid the high observability due to the cavity resonance or electromagnetic wave leakages from the bridge of a battleship or the cockpit of an aircraft, this paper presents a transparent conductive oxide coated structure to prevent the incoming/outgoing electromagnetic waves. Currently, most of the RCS reduction technologies were focused on radar absorbing material such as paints based on conductive or magnetic materials in the fuselage, and there is not much research on countermeasures for achieving the low observability of materials that required optical transparency in actual weapon systems. In this study, the transmission/reflection and absorption performance of the ITO coated structure according to the change of the surface resistance of the transparent conductor were analyzed. Finally, the relationship between the electromagnetic and optical characteristics was established through fabrication and measurement.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2004년도 춘계총회 및 연구발표회 초록집
• /
• pp.39.4-39.4
• /
• 2004

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.13-16
• /
• 2002

Ru thin films were deposited on bi-axially textured Ni tape using rf-magnetron sputtering for a conductive buffer layer of high Tc superconductor applications. (002) textured Ni films were fabricated as the deposition temperature was over $600^{\circ}C$. Rocking curves of the films showed similar alignment to those the Ni tapes. The resistivity of the tapes fabricated below $600^{\circ}C$ was around 20$\mu\Omega$-cm which is good for the conductive layer for tape superconductor applications.

• Carbon letters
• /
• 제2권3_4호
• /
• pp.165-169
• /
• 2001

Modification of C/C composite bipolar plate for improving electrical conductivity was carried out by addition of electroconductive carbon black (EC-CB). Carbon black was carefully mixed to methanol-containing phenolic resin, impregnated into 2D-carbon fabrics, hot pressed and then carbonized to obtain composite plate. Inclusion of electro-conductive carbon black enhanced the electrical conductivity of the C/C composites by increasing the conduction path. Addition of 10 vol% carbon black increased the electrical conductivity from 5.5/${\Omega}cm$ to 32/${\Omega}cm$ and reduced the crack formation by filling effect, resulting in the increase of flexural properties of composite plate. However, at carbon black content over 10 vol%, flexural properties decreased by delaminating role of excess carbon black at the interface in C/C composites.

• 한국재료학회지
• /
• 제25권7호
• /
• pp.341-346
• /
• 2015

The feasibility of obtaining graphitic carbon films on targeted substrates without a catalyst and transfer step was explored through the pyrolysis of the botanical derivative camphor. In a horizontal quartz tube, camphor was subjected to a sequential process of evaporation and thermal decomposition; then, the decomposed product was deposited on a glass substrate. Analysis of the Raman spectra suggest that the deposited film is related to unintentionally doped graphitic carbon containing some $sp-sp^2$ linear carbon chains. The films were transparent in the visible range and electrically conductive, with a sheet resistance comparable to that of graphene. It was also demonstrated that graphitic films with similar properties can be reproduciblyobtained, while property control was readily achieved by varying the process temperature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.724-726
• /
• 2007

We have developed the synthesis method to reduce the surface oxide layer in Cu nanoparticle, which is based on controlling the molecular weight of capping polymer. In addition, we demonstrated how the variation of oxide layer thickness influences the resistivity of conductive Cu film.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.75-76
• /
• 2006

New PM route via bulk mechanical alloying is developed to fabricate the solid solution semi-conductive materials with $Mg_2Si_{1-x}Ge_x$ and $Mg_2Si_{1-y}Sn_y$ for 0 < x, y < 1 and to investigate their thermoelectric materials. Since $Mg_2Si$ is n-type and both $Mg_2Ge$ and $Mg_2Sn$ are p-type, pn-transition takes place at the specified range of germanium content, x, and tin content, y. Through optimization of chemical composition, solid-solution type thermoelectric semi-conductive materials are designed both for n-and p-type materials.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2004년도 춘계학술대회
• /
• pp.96-99
• /
• 2004

A new proton conductive inorganic-organic hybrid membrane doped with $H_3PO_4$ was fabricated via sol-gel process wit 3- glycidoxypropyltrimethoxysilane(GPTMS), 3-aminopropyltriethoxysilane(APTES) and tetraethoxysilane(TEOS) asprecursors. Theproto conductivity of about 3.0$\times10^{-3}S/cm$ was obtained at $120^{\circ}C$ under $50\%$ relative humidity (R.H). DTA curves showed that the thermal stability of the membrane is significantly enhanced by the presence of $SiO_2$ framework up to $250^{\circ}C$. SEM and XRD revealed that the gel is microporou and amorphous. The addition of APTES improved the conductivity of the membranes and the effect of the APTES on the conductivity was also discussed in this paper.

• 센서학회지
• /
• 제30권2호
• /
• pp.67-70
• /
• 2021

A new button-shaped electrical device was developed for a smart fabric. This electric button can be sewn anywhere on the garment, similar to a traditional button fastener. t not only performs a decorative function but also makes the fabric suitable for use in Internet of Things (IoT) applications. It has metallic through-holes such that it can be fastened onto a fabric by conductive sewing threads. When threaded through metallic holes, the button can communicate with the external device by transmitting and receiving data. In addition, it adds specific functions by stacking a detachable application layer on the base layer. It is robust to frequent washing, and thus has excellent repeatability for use as an IoT device. The feasibility of the electric button was successfully demonstrated by its ability to identify the physical activities of walking and running, monitoring ambient temperature, and turning on LED lights.

• 한국재료학회지
• /
• 제24권9호
• /
• pp.502-507
• /
• 2014

Recently, improvement in the conversion efficiency of silicon-based solar cells has been achieved by decreasing emitter doping concentration, because the lightly doped emitter can effectively prevent the recombination of electrons and holes generated by solar light irradiation. This type of emitter is very thin due to the low doping concentration, thus conductive materials (i.e., silver) used for front electrodes can easily penetrate the emitter during a firing process because of their large diffusivity in silicon. This results in junction leakage currents which might reduce cell efficiencies. In this study, $Al_2O_3$-coated Ag powders were synthesized by an ultrasonic spray pyrolysis method and applied to the conductive materials of the front electrode to control the junction leakage current. The $Al_2O_3$ shell obstructs the Ag diffusion into the emitter during the firing process. The powder is spherical with a core-shell structure and the thickness of the $Al_2O_3$ shell is tens of nanometers. Solar cells were fabricated using pure Ag powders or the $Al_2O_3$-coated Ag powder as front electrode materials, and the conversion efficiency and junction leakage current were compared to investigate the role of the $Al_2O_3$ shell during the firing processes.